Package Contents - Triton AX Pro Manual

CONFIGURING AUDIO CONTROLLER
(Advanced)

 Optical Input
 AC Input
 Select Volume/Prologic OR Time Delay/DRC
 Time Delay Zone Selector
 Power Button
 Pro Logic / DRC button
 Volume - / TD+ button
 Volume- / TD+ button
 Dual Headphone Out
 Analog 5.1 output
 USB voice communications port
 Power LED - Indicates unit has power
 Digital - Unit is receiving a 5.1 Dolby Digital signal (Best)
 PL - Unit is receiving a Pro Logic signal
 DRC - Dynamic Range Control is turned on
The default settings of the audio controller are pre-optimized but can
be modifi ed for user customization.
VOL/PL
Move the selector to the VOL/PL position
Button  will select Pro Logic on/off
Button  and  will adjust volume up and down
(Pro Logic) When Dolby Pro Logic is "on" with an audio source
that is 2 channel, the audio will then be converted to 5.1 channel
sound. When Dolby Pro Logic is "off" with an audio source that is 2
channel, the audio will remain 2 channel stereo.
(Volume up/down) Pressing the volume up/down one time will adjust
the volume 1dB in either direction. Press and hold the volume up
to increase the volume to the maximum level. Press and hold the
volume down to decrease the volume to the minimum level (mute).
TD/DRC (Time Delay, Dynamic Range Control)
Move the selector to the TD/DRC position
Button  now becomes DRC (Dynamic Range
Compression) on/off
TD/DRC (Continued)
Button  and  will now increase or decrease
the Time-Delay
- Toggle  to change the time delay between the front channel and
the center channel, or the front channel and rear channels
Time Delay – Some users add time delay to the surround channels
to make the 3d effect more dramatic. To do this, set the switches as
shown.
Then press the + key  about 10 times, this will set the time delay to
max for the "Surround" channels. You can also adjust the time delay to
the center channel, simply switch the left switch to the left, however
for gaming, this typically is less commonly used.
You can also use the time delay settings if you plug auxiliary speakers
into the side outputs, and use our device to output 5.1 to them.















Package Contents

A - AX Pro Headset with in-line audio control module
B - Removable Earcap Covers
C - Replaceable Ear and Headband Pads
D - Removable Microphone
E - AX Pro Dolby Digital & Pro Logic Audio Controller
F - Double Power adaptors
G - Xbox Live communication recoil cable
H - Digital Fiber Optic Cable (Remove protective caps before installing.)
I - Communication USB Cable
J - G9 Adaptor
Images not to scale.





v1: Volume Adjustment Switch
v2: Master Mute
v3: Mic Mute
v4: Chat Voice Volume Knob
v5: Individual Sound Field Switches
v6: Xbox Live Connection
Volume Control
To adjust the Master Volume, move the "Volume Adjustment Switch"(v1)
one way or the other. To mute the master volume, press inward on the
toggle switch (v2)
To adjust the volume of each channel individually, fi rst press one of
the "Individual Sound Field Switches"(v5) and then adjust the Volume
Adjustment Switch(v1). The color will change based upon the volume
level. See back of controller for key.
Repeat this for all sound fi elds you wish to adjust.
To adjust master volume after this, you must wait 3 seconds for all the
channels to illuminate.
To reset the volume of all channels to the same level, simply adjust the
master volume level, all the way to the
lowest level, then turn it back up again.
Voice Communication Settings
To adjust the volume of the voices of
other players, use the "Chat Voice Volume Knob" (v4).
To Mute your voice so others cannot
hear you, toggle the "Mic Mute"(v3) switch.
Removing Headrail Pad
To remove top head rail pad, hold headset
upside down, with microphone side of headset
close to your chest. Slide the pad away from
your body, and towards the "R" emblem on the
head rail. Once it pulls up a little, pull the pad
off. Installation is reverse of removal.




Remove
protective
caps before
installing.

v2
v1
v5
v6
v4
v3
Slide
Pad