Advertisement
Quick Links
Advertisement
Related Manuals for Legacy Goliath XD
Summary of Contents for Legacy Goliath XD
- Page 1 Goliath XD...
- Page 2 Speaker Connections Wave Launch Processor 2 20...
- Page 3 Goliath X...
- Page 4 Goliath X...
- Page 5 • • • • • • • • •...
- Page 9 If you are utilizing Goliath XD as the dedicated LFE channel for a surround system, connect the LFE output from your surround processor to the XLR input 3 of your Xilica processor. Connect an XLR cable from the Xilica processor output 1 to the XLR input on the rear of the Goliath XD subwoofer.
- Page 10 Connect an XLR cable from output 4 of the Xilica processor to the back of the Goliath XD subwoofer. If you are using a second Goliath XD subwoofer, connect an XLR cable from output 8 of the Xilica processor to the back of the right Goliath XD subwoofer for stereo subwoofer performance.
- Page 11 Goliath XD Push the switch upward to turn the unit on. Power up the Xilica processor before the Goliath XD subwoofer to avoid sending unnecessary transients through the subwoofer.
- Page 12 Wave Launch Processor The high definition Digital Wavelaunch Processor hosts a LEGACY custom algorithm which automatically loads when the proc- essor is powered on. Factory settings are ‘plug and play’, and do not require a computer to utilize. Connections between the preamp, power amplifier, and speakers should be as shown on previous pages.
- Page 13 Wave Launch Processor Downloading and Installing the XConsole software DownloadingFromLegacy Audio Visit www.LegacyAudio.com, and navigate to the Goliath XD Subwoofer product page. Click on the details tab, and click "How to Control Legacy Speakers" Installing - Double click on the install file and follow the on– screen instructions to install the...
-
Page 14: Continued On Next Page
Wave Launch Processor The XP processor will allow you to make adjustments to your system from a laptop computer from your listener position. Connecting Your Computer with the XP-4080 Processor - Connecting will require a long USB Device cable. These can be found at most electronic or big box stores. It is the same cable that a USB printer would use. - Page 15 Wave Launch Processor - Go back to the XConsole software. At the top of the screen click “Setup” then “Port Connections” This bring up a new dialog box. Select the COM port number you obtained from the device manger and click “OK.” The software will warn you that you must restart the software for your changes to take effect.
- Page 16 Wave Launch Processor Making Adjustments with Wavelaunch Processor After installing the included software, connect the processor to the computer via a USB cable. Launch the XConsole software. When asked if you want to connect to the device, click yes. In the Device List, click on the device that is connected. This will launch the program that is currently on the processor.
- Page 17 Adjustments to the processor can be made to “Out 1 Sub L" and "Out 5 Sub R" when using a second subwoofer . The preset shown on the right is for 2 Goliath XD within a Whisper XD system. Adjustments to the processor can be made to “Out 4:...
- Page 18 Wave Launch Processor Making a boost with the parametric EQ In this example, we have selected Parametric EQ 2 (PEQ2) by clicking in its box, which will turn red to indicate your selection. Once highlighted, locate the blue boxes with up and down arrows, at the bottom of the interface. These arrows are used to in- crease or decrease the gain, frequency and Q of the selected parametric EQ.
- Page 19 Wave Launch Processor Making a cut with the graphic EQ In this example, we have selected Graphic EQ 8 by clicking in its box which will turn red to indicate your selection. Once high- lighted, locate the blue boxes with up and down arrows, at the bottom of the interface. These arrows are used to increase or de- crease the gain of the selected graphic EQ.
- Page 20 Wave Launch Processor Adjusting using the EQ plot Adjustments made to both the parametric and graphic EQ are reflected in the graph occupying the upper portion of the screen. You can select them by clicking on their number, and dragging up to boost, and down to cut. Dragging to the left decreases the frequency, while dragging to the right increases the frequency.
- Page 21 Adjusting Goliath X D Gain: . Be sure to adjust the Gain in the row corresponding to your subwoofer. Filter: Clicking this button allows you to access the EQ capabilities of the subwoofer. The crossover point and slope can also be adjusted on the right via the X-Hi/LPF section. Follow the instructions on the previous pages for making adjustments Polarity While seated at your listening position, click the Polarity button on your subwoofer output.
- Page 22 •Goliath X Goliath X Two separate s (1,000 watts total) Goliath X multiple subwoofe TheXilica processor allows for precise control over , allowing Goliath XD to...
- Page 23 Mutually coupled, dynamically stabalized Subwoofer : Silver/Graphite/Rohacell composite diaphragm Radiato r : mass loaded, bottom & rear firing (2) 5 ultra efficient CE®Power modules 2-150 +/- 2 dB, Includes 24 bit processor Phase Adjustment: tinuous time adjustment Blend EQ: 16 parametric bands Linkwitz-Riley 6/12/24/48 Inputs: 1 .125...