Advertisement
Quick Links
Using the wireless bicycle computer, you can measure your speed and distance travelled with a great degree of
accuracy.
Product Checklist
The following items are included:
- 1 x Digital Readout Computer
- 1 x CR2032 Battery
- 1 x Magnet
- 1 x Gauge Stand
- 1 x Sensor Ziplock Bands
GETTING STARTED
1.
Remove the battery cover from the back of the digital readout computer and insert a CR2032 battery
(not supplied) into the case, in accordance with the correct polarity. Remove the battery cover from the
wireless sensor and put a 23A 12V battery (not supplied) into the battery compartment, in accordance with the
correct polarity.
2.
Install the sensor onto the front tyre fork of your bicycle by threading the ziplocks through the gaps
at the back of the sensor. Ensure it is placed so that the sensor is pointing outwards. The sensor can also be
underlaid with the adhesive backup plate to position it correctly.
3.
Unscrew the end of the magnet and wrap it around a spoke on your tyre. Position it to ensure it will pass by the
sensor. The magnet must face the sensor, and the two objects should pass each other, with a distance of
approximately 1mm between them. Adjust the relative locations of the sensor and magnet if necessary.
4.
The gauge stand can be fastened to the handbars via the ziplock straps being threaded through the
back of the stand (between the gauge and the handlebar barrier). Ensure that when you attach it, the
small plastic hook is at the bottom, as the Digital Readout Computer slots in above this.
5.
Slot the computer into the top of the gauge stand and press down until it clicks into place. To
remove, simply apply slight pressure to the small plastic hook at the bottom of the computer and
slide it upwards.
6.
Turn the front wheel until the magnet passes the sensor. Check the screen to confirm that you have
a signal. If there is no signal or the computer has not reacted, please check the relative locations of
the sensor and magnet, plus confirm that both units have functioning batteries inserted correctly.
You now have your speedometer installed and are ready to configure and use it!
Wireless Bicycle Computer
Quick Start Guide
KHBICSPDMTR
Advertisement
Related Manuals for Kogan uick Start GuideKHBICSPDMTR
Summary of Contents for Kogan uick Start GuideKHBICSPDMTR
- Page 1 Wireless Bicycle Computer Quick Start Guide KHBICSPDMTR Using the wireless bicycle computer, you can measure your speed and distance travelled with a great degree of accuracy. Product Checklist The following items are included: - 1 x Digital Readout Computer - 1 x CR2032 Battery - 1 x Magnet - 1 x Gauge Stand - 1 x Sensor Ziplock Bands...
-
Page 2: Setting The Wheel Cycle
SETTING THE WHEEL CYCLE Once the battery has been installed, the screen will display '2060', with one of the numbers flashing. Select the exact cycle of your bike according to the following list. Push the right key to change the number, then press left key to confirm your selection. -
Page 3: Setting The Clock
SETTING THE CLOCK In Clock mode, press the “Left key” for 3 seconds to enter the 12/24 hr time settings. Press the left key to alternate between 12/24hr time, press the right key to confirm a selection. When the hour value begins to flash, press the left key to change it, then press the right key to confirm your selection. -
Page 4: Current Speed
(SCAN ） In this mode, the screen will display DST、MXS、AVS、TM in sequence. AUTO OFF – ENERGY SAVING After 300 seconds no signal input, the computer/the screen will revert to its 'OFF' state with only the clock visible on the display. You may return the device to normal operation by pressing any key. -
Page 5: Troubleshooting
- Do not disassemble the product. - Any misuse of the product will void warranty. In the event of product misuse, Kogan will not be responsible for damage or injury if applicable. - If you believe the computer has malfunctioned or requires repair, please refrain from attempting to repair it yourself.