Table of Contents
Advertisement
Operation
Basic Operation
Once you have completed the setup and configu-
ration of the AVR 4550, it is simple to operate
and enjoy. The following instructions should be
followed for you to maximize your enjoyment of
your new receiver:
Turning the AVR 4550 On or Off
• When using the AVR 4550 for the first time, you
must press the Main Power Switch
front panel to turn the unit on. This places the unit
in a Standby mode, as indicated by the amber color
of the Power Indicator
. Once the unit is in
Standby, you may begin a listening session by
pressing the System Power Control
Source button
on the front panel or the AVR
Selector
. Note that the Power
Indicator
will turn green. This will turn the
unit on and return it to the input source that was
last used. The unit may also be turned on from
Standby by pressing any of the Source Selector
buttons on the remote
or the Source button
on the front
panel.
NOTE: After pressing one of the Input Selector
buttons
(except VID4) to turn the unit on,
press the AVR Selector
to have the
remote control the AVR functions.
To turn the unit off at the end of a listening ses-
sion, simply press the System Power Control
on the front panel or the Power Off Button
on the remote. Power will be shut off to
any equipment plugged into the rear panel
Switched AC Outlets
and the Power
Indicator
will turn orange.
When the remote is used to turn the unit "off" it
is actually placing the system in a Standby mode,
as indicated by the orange color of the Power
Indicator
.
When you will be away from home for an
extended period of time it is always a good idea
to completely turn the unit off with the front
panel Main Power Switch
.
NOTE: All preset memories may be lost if the
unit is left turned off with the Main Power
Switch
for more than two weeks.
Using the Sleep Timer
• To program the AVR 4550 for automatic turn-
off, press the Sleep Button
on the remote.
Each press of the button will increase the time
before shut down in the following sequence:
90
80
70
60
50
min
min
min
min
min
40
30
20
10
OFF
min
min
min
min
The sleep time will be displayed in the Lower
Display Line
and it will count down until
the time has elapsed.
30 OPERATION
When the programmed sleep time has elapsed,
the unit will automatically turn off (to Standby
mode). Note that the front panel display will dim
to one half brightness when the Sleep function is
programmed. To cancel the Sleep function, press
and hold the Sleep Button
mation display returns to normal brightness and
the Sleep indicator numbers disappear and the
words
Information Display
on the
Source Selection
• To select a source, press any of the Source
Selector buttons on the remote
or the
.
NOTE: After pressing one of the Input Selector
buttons
to turn the unit on, press the
AVR Selector
control the AVR functions.
• The input source may also be changed by
pressing the front-panel Input Source Selector
button
. Each press of the button will move
the input selection through the list of available
inputs.
• As the input is changed, the AVR 4550 will
automatically switch to the digital input (if
selected), surround mode and speaker configura-
tion that were entered during the configuration
process for that source.
• The front-panel Video 4 Inputs
Digital 3 Input
or the Coaxial Digital 3
Input
may be used to connect a device such
as a video game or camcorder to your home
entertainment system on a temporary basis.
• As the input source is changed, the new input
name will appear momentarily as an on-screen
display in the lower third of the video display.
The input name will also appear in the Main
Information Display
light next to the selected input's name in the
front-panel Input Indicators
• When a pure audio input (CD, Tuner, Tape,
6/8 Channel Input) is selected, the last video
input used remains routed to the Video Out-
puts
(except from its own Video 1/2
source) and Video Monitor Output
permits simultaneous viewing and listening to
different sources.
• When a Video source is selected, its audio
signal will be fed to the speakers and the video
signal for that input will be routed to the appro-
priate Monitor Output Jack
able on a TV monitor connected to the AVR 4550.
If a component video source is connected to the
DVD
or Video 2
will be routed to the Component Video
Outputs
. Make certain that your TV is set to
the proper input to view the appropriate video
signal (composite, S-Video or component video,
see Notes for S-Video on page 16).
6-Channel/8-Channel Direct Input
• There are two input choices available for use
until the infor-
with sources such as a DVD-Audio or SACD play-
er that are connected to the 8-Channel Direct
Inputs
appear in the Main
ing to the way your system and source equip-
.
ment is configured:
• The
when the SBR and SBL inputs are NOT in use and
the input source device has its own internal bass
management system. This input passes the input
from the source directly through to the volume
control without any analog to digital conversion
and it mutes the unused input jacks to prevent
to have the remote
unwanted noise from interfering with system per-
formance.
• The
used when an input is connected to all eight
8-Channel Direct Inputs
input source device has its own internal bass
management system. This input passes the input
from the source directly through to the volume
control without any analog to digital conversion
and it mutes the unused input jacks to prevent
unwanted noise from interfering with system
performance.
Note that when the 6-Channel or 8-Channel
, Optical
Direct Input is in use, you may not select a sur-
round mode, as the external decoder determines
the processing in use. In addition, there is no
signal at the record outputs or bass management
when the 6-Channel or 8-Channel Direct Input is
in use and the tone or balance controls will not
function.
and a green LED will
.
. This
and will be view-
Component Inputs, it
. Select the appropriate input accord-
input should be used
should be
and when the
Hide quick links:
Advertisement
Table of Contents
