Page 1
GA - 586MS PCI - ISA SOLUTION ¬ Support Win95 Soft-Power off. ¬ Support Modem Ring On by Com2. If ATX-Power is using. If Cyrix CPU is Using, make sure CPU Date-Code After 6620. PENTIUM PCI - ISA BUS MAINBOARD REV.1.0 Second Edition...
Page 16
GA-586MS Quick Installation Guide of Jumper setting: GN: Green Function Switch Close One Time: For system entering Green mode. Open: Normal operation. GD: Green Function LED Pin No. Function LED anode (+) LED cathode (-)
Page 17
Table of Contents RST: Reset Switch Close: For hardware reset system. Open: Normal operation. SPK: Speaker Connector Pin No. Function Date...
Page 19
Table of Contents POWER: Power Connector Pin No. Function Power Good signal. 2,10,11,12 VCC (+5V) +12V -12V 5,6,7,8 HD: IDE Hard Disk Active LED Pin No. Function LED anode (+) LED cathode (-) LED cathode (-) LED anode (+)
Page 20
GA-586MS TB: Turbo Switch Function Reserved TD: Turbo LED Connector Pin No. Function LED anode (+) LED cathode (-)
Page 21
Table of Contents JP2: CPU Cooling Fan Power Connector Pin No. Function +12V...
Page 22
GA-586MS SOFT-PWR: Close One Time : Switch power from on to off or from off to on. Pin No. Function CTRL- Signal RED LINE IDE1: For Primary IDE port...
Page 23
Table of Contents RED LINE IDE2: For Secondary IDE port J6: For Floppy port RED LINE J4: PS/2 Mouse PS/2 Mouse Pin No. Function Key Data VCC (+5V) Key Clock.
Page 24
GA-586MS J5: Keyboard Connector PS/2 Keyboard Pin No. Function Key Data VCC (+5V) Key Clock.
Page 25
Table of Contents J3: ATX Power Connector Pin No. Function 1,2,11 3,5,7,13,15,16,17 4,6,19,20 Power good 5VSB +12V -12V PSON J2: COMA Port COM A...
Page 26
GA-586MS J16:COMB PORT RED LINE J7:LPT PORT...
Page 28
GA-586MS The author assumes no responsibility for any errors or omissions which may appear in this document nor does it make a commitment to update the information contained herein. IBM PC/AT, PC/XT are trademarks of International Business Machine Corporation. PENTIUM is a trademark of Intel Corporation.
Table of Contents TABLE OF CONTENTS 1. INTRODUCTION ..................1-1 1.1. PREFACE..................... 1-1 1.2. KEY FEATURES................... 1-1 1.3. PERFORMANCE LIST ................1-2 1.4. BLOCK DIAGRAM ................1-3 1.5. INTRODUCE THE PCI - BUS ..............1-4 1.6. FEATURES................... 1-4 2. SPECIFICATION ..................2-1 2.1.
Page 30
GA-586MS 4.3.1. Main Menu .................. 4-3 4.3.2. Status Page Setup Menu / Option Page Setup Menu ....4-3 4.4. THE MAIN MENU.................. 4-3 4.5. STANDARD CMOS SETUP MENU............4-5 4.6. BIOS FEATURES SETUP ..............4-9 4.7. CHIPSET FEATURES SETUP............... 4-12 4.8.
Introduction INTRODUCTION 1.1. PREFACE Welcome to use the GA - 586MS motherboard. The motherboard is a Pipeline 256/512 KB CACHE PENTIUM Processor based PC / AT compatible system with ISA bus and PCI Local Bus, and has been designed to be the fastest PC / AT system.
GA-586MS 1.3. PERFORMANCE LIST The following performance data list is the testing results of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users. (The different Hardware & Software configuration will result in different benchmark testing results.)
Introduction 1.4. BLOCK DIAGRAM SRAM Pentium CPU Host Address Bus Host Data Bus MA[11:0] DRAM F244 SiS 5596 MD[63:0] Monitor Address/Data PCI Bus DMA PnP Port (optional) SiS 5513 IRQ PnP Port XD BUS IDE Bus LS245 SD[15:8] LA[23:17] SA[19:0] SD[7:0] 74F04 Power,RESET...
GA-586MS 1.5. INTRODUCE THE PCI - BUS Connecting devices to a CPU local bus can dramatically increase the speed of I/O-bound peripherals with only a slight increase in cost over traditional systems. This price / performance point has created a vast market potential for local bus products.
Hardware Installation HARDWARE INSTALLATION 3.1. UNPACKING The mainboard package should contain the following: The GA - 586MS mainboard. USER'S MANUAL. Diskettes for BUS Master IDE Driver & VGA Driver. The mainboard contains sensitive electric components which can be easily damaged by static electricity, so the mainboard should be left in its original packing until it is installed.
GA-586MS SOFTPW JP11 JP37 JP14 FLOPPY IDE2 IDE1 BIOS SRAM 5596 5513 SRAM SIMM4 SIMM3 SIMM2 SIMM1 PCI2 PCI3 SLOT1 SLOT2 SLOT3 SLOT4 PCI1 +12V JP35 COMB W83877 PS/2 MOUSE KEYBOARD 8042 COMA ×Figure 3.1Ø 3.3. QUICK REFERENCE FOR JUMPERS & CONNECTORS JP2: CPU Cooling Fan Power Connector Pin No.
Page 39
Hardware Installation LED anode (+). LED cathode (-). LED cathode (-). LED anode (+). JP37: Green Function Switch Pin No. Function Close For system entering Green mode ( Suspend mode). Open Normal operation. J1: Power Connector Pin No. Function Power Good signal 2,10,11,12 VCC (+5V) +12V...
Hardware Installation J4,J5 For PS/2 Mouse port & PS/2 Keyboard Port. J2,J16 For COM A (Serial port1) & COM B (Serial port2) 3.4. DRAM INSTALLATION ( EDO & F.P. ) The mainboard can be installed with 4 / 8 / 16 / 32 MB 72 pins SIMM module DRAM, and the DRAM speed must be 60 or 70 ns.
Hardware Installation Before the CPU is installed, the mainboard must be placed on a flat plane in order to avoid being broken by the pressure of CPU installation. 3.7. COMS RTC & ISA CFG CMOS SRAM Built-in Rel Time Clock (RTC) With 256B CMOS SRAM in 5513. 3.8.
GA-586MS 3.13. GREEN FUNCTION INSTALLATION For the purpose of power saving, there are two jumpers, GN and GD, to make sure that the power saving function is working. The GD is an indicator (green LED) for green function. If the green LED is ON, the system is operating in green mode.
BIOS Configuration BIOS CONFIGURATION Award's BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS SRAM so that it retains the Setup information when the power is turned off. 4.1.
GA-586MS 4.2. CONTROL KEYS Up arrow Move to previous item Down arrow Move to next item Left arrow Move to the item in the left hand Right arrow Move to the item in the right hand Esc key Main Menu - Quit and not save changes into CMOS...
BIOS Configuration 4.3. GETTING HELP 4.3.1. Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. 4.3.2. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item.
GA-586MS This setup page includes all the items in a standard compatible BIOS. BIOS features setup This setup page includes all the items of Award special enhanced features. Chipset features setup This setup page includes all the items of chipset special features.
Page 49
BIOS Configuration select the value you want in each item. ROM PCI / ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE, INC. Date (mm:dd:yy) : Fr i, Mar 1 1996 Time (hh:mm:ss) : 16 : 49 : 18 HARD DISKS TYPE SIZE CYLS HEAD...
Page 50
GA-586MS Primary HDDs / Secondary HDDs The category identify the types of hard disk drive that has been installed in the computer. There are 45 pre-defined types and a user definable type. Type 1 to Type 45 are pre-defined. Type User is user-definable and type Auto will automatically detect HDD's type..
Page 51
BIOS Configuration capacity. 1.2M, 5.25 in. 5-1/4 inch AT-type high-density drive; 1.2 megabyte capacity (3-1/2 inch when 3 Mode is Enabled). 720K, 3.5 in. 3-1/2 inch double-sided drive; 720 kilobyte capacity 1.44M, 3.5 in. 3-1/2 inch double-sided drive; 1.44 megabyte capacity.
Page 52
GA-586MS system will be stopped and you will be prompted All,But Keyboard The system boot will not stop for a keyboard error; it will stop for all other errors All, But Diskette The system boot will not stop for a disk error; it will...
BIOS Configuration Expanded Memory. Other Memory This refers to the memory located in the 640K to 1024 K address space. This is memory that can be used for different applications. DOS uses this area to load device drivers to keep as much base memory free for application programs.
Page 54
GA-586MS access the boot sector or hard disk partition table CPU Internal Cache / External Cache These two categories speed up memory access. However, it depends on CPU / chipset design. The default value is Enabled. Enabled Enable cache function.
Page 55
BIOS Configuration Boot Up NumLock Status The default value is On. Keypad is number keys Keypad is arrow keys Security Option This category allows you to limit access to the system and Setup, or just to Setup. The default value is Setup. System The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt...
GA-586MS 4.7. CHIPSET FEATURES SETUP ROM PCI / ISA BIOS INTEGRATED PERIPHERALS AWARD SOFTWARE, INC. ISA Bus Clock : PCI CLK/4 System BIOS Cacheable : Enabled Video BIOS Cacheable : Enabled VGA Shared Memory Size : 1MB VGA Memory Clock (MHz)
Page 57
BIOS Configuration Enabled Enable video BIOS cacheable. Disabled Disable video BIOS cacheable. VGA Shared Memory Size: The default value is 1MB. 0.5MB Set VGA Shared Memory Size to 0.5MB 1 MB Set VGA Shared Memory Size to 1 MB 1.5MB Set VGA Shared Memory Size to 1.5MB 2 MB Set VGA Shared Memory Size to...
GA-586MS 4.8. POWER MANAGEMENT SETUP ROM PCI / ISA BIOS POWER MANAGEMENT SETUP AWARD SOFTWARE, INC. Power Management : Enabled VGA Activity : Disabled PM Control by APM : Yes IRQ3 (COM 2) : Enabled Video Off Method : DPMS Supported...
Page 59
BIOS Configuration Video off Method The default value is DPMS Supported V/H SYNC+Blank BIOS will turn off V/H-SYNC when gets into Green mode for Green monitor power saving. Blank Screen BIOS will only black monitor when gets into Green mode. DPMS Supported BIOS will use DPMS Standard to control VGA card.
Page 60
GA-586MS The default value is Enable. Enable Enable PCI/ISA Master Activity. Disable Disable PCI/ISA Master Activity. IRQ1-15 Activity: The default value is Enable. Enable Enable IRQ1-15 Activity. Disable Disable IRQ1-15 Activity. VGA Activity: The default value is Disable. Enable Enable VGA Activity.
BIOS Configuration 4.9. PNP/PCI CONFIGURATION ROM PCI / ISA BIOS PNP/PCI CONFGURATION AWARD SOFTWARE, INC. Resources Controlled By : Manual PCI IRQ Actived By : Level Reset Configuration Data : Disabled IRQ-3 assigned to : Legacy ISA IRQ-4 assigned to : Legacy ISA IRQ-5 assigned to : PCI/ISA PnP...
GA-586MS 4.10. LOAD BIOS DEFAULTS ROM PCI / ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP/PCI CONFIGURATION...
BIOS Configuration 4.11. LOAD SETUP DEFAULTS ROM PCI / ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP/PCI CONFIGURATION HDD LEVEL FORMAT Load SETUP Defaults (Y/N)? N LOAD BIOS DEFAULTS...
GA-586MS 4.12. INTEGRATED PERIPHERALS ROM PCI / ISA BIOS PNP/PCI CONFGURATION AWARD SOFTWARE, INC. Internal PCI/IDE : Both IDE Primary Master PIO : Auto IDE Primary Slave PIO : Auto IDE Secondary Master PIO : Auto IDE Secondary Slave PIO...
Page 65
BIOS Configuration The default value is Auto. Auto BIOS will automatically defect the IDE HDD Accessing mode. Mode0~4 Manually set the IDE Accessing mode. IDE Secondary Master PIO (for onboard IDE 2nd channel). The default value is Auto. Auto BIOS will automatically defect the IDE HDD Accessing mode.
GA-586MS 3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8H. 2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8H. 3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8H. 2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8H.
BIOS Configuration ENTER PASSWORD ROM PCI / ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP/PCI CONFIGURATION HDD LOW LEVEL FORMAT LOAD BIOS DEFAULTS Enter Password: SAVE &...
Page 68
GA-586MS ROM PCI / ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP/PCI CONFIGURATION HDD LOW LEVEL FORMAT LOAD BIOS DEFAULTS SAVE &...
BIOS Configuration 4.15. HDD LOW LEVEL FORMAT ROM PCI / ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP/PCI CONFIGURATION HDD LOW LEVEL FORMAT LOAD BIOS DEFAULTS...
GA-586MS 4.16. SAVE & EXIT SETUP ROM PCI / ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP/PCI CONFIGURATION...
BIOS Configuration 4.17. EXIT WITHOUT SAVING ROM PCI / ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP/PCI CONFIGURATION HDD LEVEL FORMAT Quit Without Saving (Y/N)? N LOAD BIOS DEFAULTS...
GA-586MS 5.2. I/O & MEMORY MAP MEMORY MAP: [0000000-009FFFF] System memory used by DOS and application program. [00A0000-00BFFFF] Display buffer memory for VGA/ EGA/CGA/MONOCHROME adapter. [00C0000-00DFFFF] Reserved for I/O device BIOS ROM or RAM buffer. [00E0000-00EFFFF] Reserved for PCI device ROM.
Page 76
AT Technical Information NMI: Parity check error IRQ (H/W): 0 System TIMER interrupt from TIMER-0 1 KEYBOARD output buffer full 2 Cascade for IRQ 8-15 3 SERIAL port 2 4 SERIAL port 1 5 PARALLEL port 2 6 FLOPPY DISK adapter 7 PARALLEL port 1 8 RTC clock 9 Available...
GA-586MS 5.5. RTC & CMOS RAM MAP RTC & CMOS: Seconds Second alarm Minutes Minutes alarm Hours Hours alarm Day of week Day of month Month Year Status register A Status register B Status register C Status register D Diagnostic status byte...
GA-586MS APPENDIX A: POST MESSAGE When the BIOS encounters an error that requires the user to correct something, either a beep code will sound or a message will be displayed in a box in the middle of the screen and the message PRESS F1 TO CONTINUE, CTRL-ALT-ESC OR DEL TO ENTER SETUP will be shown in the information box at the bottom.
Page 82
Appendix A: Post Message Display switch on the motherboard can be set to either monochrome or color. This indicates the switch is set to a different setting than indicated in Setup. Determine which setting is correct, and then either turn off the system and change the jumper, or enter Setup and change the VIDEO selection.
Page 83
GA-586MS Ö Invalid EISA Configuration PLEASE RUN EISA CONFIGURATION UTILITY The non-volatile memory containing EISA configuration information was programmed incorrectly or has become corrupted. Re-run EISA configuration utility to correctly program the memory. When this error appears, the system will boot in ISA mode, which allows you to run the EISA Configuration Utility.
Page 84
Appendix A: Post Message This message is used in conjunction with the I/O CHANNEL CHECK and RAM PARITY ERROR messages when the segment that has caused the problem has been isolated. Ö PRESS A KEY TO REBOOT This will be displayed at the bottom screen when an error occurs that requires you to reboot.
Page 85
GA-586MS Indicates the present boot attempt has been aborted and the system must be rebooted. Press and hold down the CTRL and ALT keys and press DEL. Ö Wrong Board In Slot PLEASE RUN EISA CONFIGURATION UTILITY The board ID does not match the ID stored in the EISA non-volatile memory.
Appendix B: Post Codes APPENDIX B: POST CODES EISA POST codes are typically output to port address 300h. ISA POST codes are typically output to port address 80h. POST Name Description Turn Off Chipset OEM Specific-Cache control. Cache Processor Test 1 Processor Status (1 FLAGS) Verification.
Page 88
GA-586MS Memory presence test. OEM chip set routines. Clear low 64 K of memory. Test first 64 K memory. Early Cache Cyrix CPU initialization. Initialization Cache initialization. Setup Interrupt Initialize first 120 interrupt vectors with Vector Table SPURIOUS_INT-HDLR and initialize INT 00h-1Fh according to INT_TBL.
Page 89
Appendix B: Post Codes Display CPU clock. 1B-1E Reserved Set EISA Mode If EISA non-volatile memory checksum is good, execute EISA initialization. If not, execute ISA tests an clear EISA mode flag. Test EISA Configuration Memory Integrity (checksum & communication interface). Enable Slot 0 Initialize slot 0 (System Board).
Page 90
GA-586MS Reserved 48-4D Reserved Manufacturing Reboot if Manufacturing POST Loop pin is set. POST Loop or Otherwise display any messages (i.e., any non-fatal Display Messages errors that were detected during POST) and enter Setup. Security Check Ask password security (optional).
Appendix D: Problem Sheet APPENDIX D: PROBLEM SHEET 1. Customer Data Tel. No. Name Fax. No. Address Purchase Date 2. Mainboard Date Rev. No. Model NO. Serial No. 3. System Configuration CPU Type: CPU Brand: CPU Speed: q 16 q 32 MB DRAM Type: q 80 q 70...