1. Manuals
  2. Brands
  3. Firenzi Manuals
  4. Hob
  5. FGH 610
  6. Instruction booklet

Firenzi FGH 610 Instruction Booklet

Hide thumbs
Table of Contents

Advertisement

Quick Links

GAS HOB
FGH 610
INSTRUCTION BOOKLET
GB
35685-3401

Advertisement

Table of Contents
loading

Related Manuals for Firenzi FGH 610

Summary of Contents for Firenzi FGH 610

  • Page 1 GAS HOB FGH 610 INSTRUCTION BOOKLET 35685-3401...

  • Page 3: Important Safety Information

    Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 950950 Installation Service This hob should only be repaired or serviced by an This hob must be installed by qualified personnel, authorised Service Engineer and only genuine according to the manufacturer’s instructions and to approved spare parts should be used.

  • Page 4: Table Of Contents

    Contents For the Installer For the User Engineers technical data Important Safety Information Installation Description of the Hob Operation Building In Maintenance and Cleaning Electrical connections Wiring Diagram Something Not Working? Fault Finding Service and Spare Parts Commissioning Guarantee Conditions Conversion from Natural Gas to LPG Description of the Hob 1.

  • Page 5: Operation

    Operation HOB BURNERS If you use a saucepan which is smaller than the To light a burner, turn the relevant control knob recommended size, the flame will spread beyond anticlockwise to maximum position. At the same time the bottom of the vessel, causing the handle to push the electric ignition pushbutton which is marked by overheat.

  • Page 6: Something Not Working

    Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.

  • Page 7: Guarantee Conditions

    We, EHP, undertake that if, within 12 months of the date your guarantee moves with you to your new home of the purchase, this Firenzi appliance or any part thereof subject to the following qualifications: is proved to be defective by any reason only of faulty...

  • Page 8: Engineers Technical Data

    Instructions for the Installer Engineers technical data OVERALL DIMENSIONS SUPPLY CONNECTIONS Gas: Width: 580 mm. RC 1/2 inch (1/2 inch male) Rear right hand corner Depth: 500 mm. Height: 8 mm. Electric: 230-240V 50Hz supply, 3 core flexible cable. CUT OUT DIMENSIONS Width: 550 mm.

  • Page 9: Installation

    Important safety requirements This hob must be installed in accordance with the Gas FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S.

  • Page 10: Building In

    Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to R 1/ FO 0814 2" (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and A) End of shaft with nut installation.

  • Page 11: Electrical Connections

    Fitting the Hob into the worktop Carry out the building in of the hob as follows: • put the seals supplied with the hob on the edges of the cut out, taking care that the seals meet without overlapping; • place the hob in the cut out, taking care that it is centred;...

  • Page 12: Wiring Diagram

    Wiring Diagram 220/240 A. IGNITOR SWITCH B. IGNITOR UNIT Fault Finding Preliminary Electrical Systems SOCKET PLUG (with cover (face view) removed) Check Earth Wire Green/Yellow Blue Brown Green START Yellow Isolate appliance and carry out: A: Earth Continuity Neutral Wire Blue check.
  • Page 13 Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse Light burner manually and replace if necessary Check polarity and Check by pass simmer earth continuity of adjusted supply point Check position of the Check earth continuity electrode of appliance...

  • Page 14: Commissioning

    Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. Turn the gas tap to the MAX position and ignite. Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.

  • Page 15: Conversion From Natural Gas To Lpg

    Conversion from Natural Gas to It is important to note that this model is designed for use TO ADJUST THE GAS RATE with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. With the aid of a thin bladed screwdriver completely The gas rate is adjusted to suit.
  • Page 16 09/03...

Table of Contents