Download Print this page

Graco 447-4-02 User Manual

Adjustable infant restraint base

Advertisement

Available languages

Available languages

Quick Links

Storing LATCH
1. For ease of storing, extend LATCH
to its maximum length.
2. Locate the storage bars on bottom of
.
infant restraint base
3. Fasten end of LATCH (without
adjustment belt) onto storage bar.
4. Repeat Step 3 for LATCH with
adjustment belt. After fastening onto
storage bar, pull on adjustment belt to
make sure LATCH is securely fastened.
5. LATCH storage should look like this
.
when complete
Storage bars
Underside of Base
4
Adjustable Infant Restraint Base
Base with LATCH
See infant restraint owner's manual for
complete installation instructions.
Your new infant restraint base is equipped with Graco's recline adjustment foot, which helps to properly recline the infant
restraint/base on the vehicle seat. Use it AFTER you have carefully followed all of the steps in your infant restraint owner's
manual.
ecline the infant restraint/base on the vehicle seat. Use it AFTER you have carefully followed all of teps in
your infant restraint owner's
The adjustable base is used along with the level indicator on the side of your infant restraint. To check the proper angle of
the infant restraint, first make sure the vehicle is on level ground and that the infant restraint/base is not tilted sideways on
the vehicle seat. Then check the level indicator. You must look straight on at the indicator.
If the indicator shows ONLY blue, the infant restraint is properly leveled.
If any orange is showing in the level indicator, the infant restraint is
either too upright or too reclined.
To lower the foot: pull down on the bottom of the foot to the desired
setting to adjust the recline
.
To raise the foot: set the base on a flat surface, push in on the fingers
on the base and push down on the base to adjust the recline
If there is still orange in the level indicator when the foot is completely
extended then place a rolled towel under the foot until ONLY blue shows.
Tighten belt through base, then reinstall infant restraint. Level indicator
should now show ONLY blue—if you still see orange, re-adjust recline
© 2002 Graco 447-4-02
! You must read and understand both the owner's
manual from the infant restraint and these
instructions before using the infant restraint and
base. Keep this sheet with the instruction booklet
in the pocket of your infant restraint for reference.
®
! This base can only be used with a Graco
Infant Restraint.
! If you do not have instructions for your infant
restraint or if you have any questions about
your product, call Graco at 1-888-224-6549 or
visit our website at www.gracobaby.com.
.
.
1

Advertisement

loading

Summary of Contents for Graco 447-4-02

  • Page 1 Underside of Base Your new infant restraint base is equipped with Graco’s recline adjustment foot, which helps to properly recline the infant restraint/base on the vehicle seat. Use it AFTER you have carefully followed all of the steps in your infant restraint owner’s manual.
  • Page 2 1. Place the base in a rear-facing position in a forward-facing vehicle seat 2. Thread the vehicle seat belt through the openings in the base . Buckle the seat belt. The seat belt should not be twisted. 3. Tighten the vehicle seat belt. Refer to your vehicle owners manual and the instructions in your infant restraint owner’s manual on tightening your vehicle belt 4.
  • Page 3 Parte inferior de la base La base de su nuevo sistema de seguridad para niños está equipada con el pie Graco de ajuste inclinable que ayuda a reclinar debidamente la base/sistema de seguridad sobre el asiento del vehículo. Úselo DESPUÉS de haber seguido detenidamente todos los pasos en el manual del propietario de su sistema de seguridad para niños.
  • Page 4 1. Coloque la base orientada hacia atrás en un asiento del vehículo orientado hacia adelante 2. Pase el cinturón del asiento del vehículo por las aperturas de la base . Trabe el cinturón del asiento. El cinturón del asiento no debe estar retorcido. 3.