Electrolux group. operating and installation instructions cooker hood 8160 d, 8190 d 8260, d 8290, d 8360, d 8390, d 8361, d 8391 d (20 pages)
Summary of Contents for AEG 1400 D
1400 D Dunstabzugshaube Afzuigkap Hotte aspirante Cooker Hood Montage- und Gebrauchsanweisung Installatie- en gebruksaanwijzing Manuel de montage et d’utilisation Operating and Installation Instructions...
Printed on recycled paper AEG - putting words into action...
Contents Safety warnings for user for kitchen unit installer Introduction Extractor version Filter version Hood operation Maintenance and care Metal grease filter Carbon filter Changing the light bulb Cleaning Special accessories Technical assistance service Guarantee conditions Service Technic Details Installation Electrical connection Wall unit mounting Wall mounting...
Safety warnings for user Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. Also, when frying, keep the deep frying pan on the cooker top/ cooker under careful control.
The national decree on fuel-burning systems specifies a maximum depression of 0.04 bar in such rooms. The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circum- stances be connected to ventilation ducts for rooms in which fuel-burning appliances are installed.
(special accessory). l You will need original AEG activated carbon filter for this function (see Special Accessories). l The unit features two outlet holes, one of which A is located on the top of the unit while the other B is located on the rear.
Hood Operation Best results are obtained by using a low speed for normal conditions and high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking then you will get an underpressure in the kitchen. It should be left on after cooking for about 15 minutes or until all odours have disappeared.
Maintenance and care The hood must always be disconnected from the mains power supply before beginning any maintenance work. Metal grease filter The purpose of the grease filters is to aspirate grease particles which form during cooking and it must always be used, either in the external evacuation or internal recycling function.
Carbon filter The activated carbon filter should only be used if you want to use the hood in its filtering function. To do this you will need an original AEG activated carbon filter (see special accessories). l Cleaning/replacing the carbon filter Unlike other carbon filters, the LONGLIFE carbon filter can be cleaned and reactivated.
Warning Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations.
Cleaning Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor’s protective grid. Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents.
Guarantee conditions Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation.The guarantee does not...
Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home.They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Senlis +33 (0) 44 62 29 29...
Electrical connection Safety warnings for the electrician Before connecting the appliance to the power supply, check that the voltage indicated on the rating plate corresponds to the mains power supply available. Appliances fitted with a plug can be connected to any standard power socket within easy access.
Wall unit mounting - Fig. 6 l Make the holes on the bottom of the cupboard (2), using the drilling template (1). Provide an hole also for exhausting pipe (4) ONLY if is decided to use the hood in Exhausting version (3). l From inside the cupboard, insert the 4 supplied screws (5) and tighten them in the appropriate holes on the appliance.
Wall mounting - Fig. 7 Sign a centerline onto the wall (1). Fit the template onto the wall (2). Fix the drilling template to the wall. Make 3 Ø 8mm holes in the wall (3), 2 at upper points, 1 as desired at lower points.