Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ryobi LCS-180
Summary of Contents for Ryobi LCS-180
- Page 1 LCS-180 CORDLESS CIRCULAR SAW OWNER’S OPERATING MANUAL...
- Page 2 DESCRIPTION 1. Lock-off Button 11.Outer Blade Washer 21.Workpiece (Not included) 2. Switch Trigger 12.Inner Blade Washer 22.C-Clamp (Not Included) 3. Dust Pipe Joint 13.To Loosen 23.Bevel Scale 4. Depth Adjustment Knob 14.To Tighten 24.Motor Housing 5. Width of Cut Scale 15.Battery Pack(Not Included) 25.Lower Blade Guard Handle 6.
- Page 3 Fig.7 Fig.8 Fig.9 Fig.10 Fig.11 Fig. 12 Fig.13 Fig. 14...
- Page 4 Fig. 15 Fig. 16 Fig.17 Fig.18 Fig.19 Fig.20 Fig.21 Fig.22...
- Page 5 Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications.
-
Page 6: General Power Tool Safety Warnings
English GENERAL POWER TOOL SAFETY WARNINGS 3. PERSONAL SAFETY a. Stay alert, watch what you are doing and use common sense when operating a power tool. WARNING Do not use a power tool while you are tired or Read all safety warnings and all instructions. under the influence of drugs, alcohol or medi- Failure to follow the warnings and instructions may result cation. -
Page 7: Specific Safety Rules
English Do not reach underneath the workpiece. The hands of untrained users. e. Maintain power tools. Check for misalignment guard cannot protect you from the blade below the or binding of moving parts, breakage of parts workpiece. and any other condition that may affect the ... -
Page 8: Additional Safety Rules
English When blade is binding, or when interrupting a Always observe that the lower guard is covering cut for any reason, release the trigger and hold the blade before placing saw down on bench or the saw motionless in the material until the floor. -
Page 9: Specifications
BATTERY PROTECTION FEATURES flats on the spindle. Larger blades will come in Ryobi 18 V lithium-ion batteries are designed with contact with the blade guard, while thicker blades features that protect the lithium-ion cells and maximize... -
Page 10: Operation
Kickback could cause you to lose control of the saw. Loss of control can lead to serious This product will accept Ryobi One+ 18 V lithium-ion injury. battery packs and Ryobi One+ 18 V nickel-cadmium battery packs. - Page 11 English Cutting warped or wet lumber. does not cover blade on the underside of work. Since blade is exposed on underside of work, Operating the tool incorrectly or misusing the tool. keep hands and fingers away from cutting area. Any part of your body coming in contact with To lessen the chance of kickback, follow these safety moving blade will result in serious injury.
- Page 12 English located on the upper blade guard. NOTE: The distance from the line of cut to the guideline is the amount you should offset the guide. Loosen the depth adjustment knob. Determine the desired depth of cut. RIP CUTTING ...
-
Page 13: Maintenance
English Release the trigger and allow the blade to come to a 0° BEVEL STOP complete stop. See Figure 22. Lift the saw from the workpiece. The saw has a 0° bevel stop that has been factory adjusted to assure 0° angle of the saw blade plate when POCKET CUTTING making 90°... - Page 14 All other parts should be replaced at an Authorized Service Center. BATTERIES This product will accept Ryobi One + 18 V lithium-ion batteries or 18 V nickel-cadmium batteries. Length of service from each charging will depend on the type of work you are doing.
- Page 15 TECHTRONIC INDUSTRIES (AUSTRALIA) PTY. LTD. Level 1. 666 Doncaster Road, Doncaster, Victoria 3108 Australia. Tel: 61 3 9840 3226 Fax No.: 613 9840 6133 www.ryobi.com.au...