American Standard Cadet 2776.XXXW Series Installation Instructions

CADET™ 5 x 32
INTEGRAL APRON WITH
REMOVABLE ACCESS PANEL
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
12
(305mm)
7-3/4
(197mm)
3/4
(19mm)
FINISHED
WALL
SEE FITTING
SPECS FOR
DIMENSIONS
(229 mm)
32
(813mm)
CUTOUT IN FLOOR
FOR DRAIN
C/L OF
2-3/8
SUPPLIES
(60mm)
C/L OF DRAIN
OPTIONAL TO
FINISHED FLOOR
7/8 WATER
USUALLY BETWEEN
RETENTION
65 & 78
FLANGE
(1651 & 1981mm)
(3 SIDES)
C/L OF
OVERFLOW
2-3/4
(70mm)
TOP OF
DECK
20
(508mm)
ROUGH
FLOOR
BATH
SUPPORT
MATERIAL
1-1/2 O.D.TAILPIECE
GENERAL SPECIFICATIONS FOR 2776 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
3
CUBE (FT )
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP
GENERAL INSTALLATION INFORMATION
BATH MAY ONLY BE INSTALLED IN A RECESS TYPE INSTALLATION.
LOCATE STUDS AS REQUIRED. INSURE ROUGH DIMENSIONS ARE PROPER, PLUMB AND SQUARE. FOR WHIRLPOOLS, ACCESS TO
PUMP/MOTOR MAY BE MADE THROUGH ACCESS OPENING IN APRON PANEL. THE FOLLOWING PROCEDURE MUST BE USED FOR
ALL INSTALLATIONS: LEVELING SUPPORT STRINGER SHOULD BE AS INDICATED.
SUPPORTED ALONG IT'S ENTIRE BOTTOM. SUPPORT WITH MORTAR OR GROUT.
POSITION BATHTUB/WHIRLPOOL WITHIN THE RECESS, CHECK LEVEL, FRONT TO BACK, SIDE TO SIDE, AND SHIM AS NECESSARY.
TO SECURE THE TUB TO WOOD STUDS USE DRYWALL SCREWS W/WASHERS OR ROOFING NAILS IMMEDIATELY ABOVE THE FLANGE OF
THE TUB. TO SECURE THE TUB TO STEEL STUDS USE 4" DRYWALL SCREWS AND FLATWASHERS.
SEE PAGE 2 FOR COMPLETE INSTALLATION INFORMATION.
CAUTION: TAKE EXTRA CARE WHEN DRIVING NAILS OR SCREWS TO AVOID DAMAGING THE TUB.
THE TILE OR SIMILAR FINISHED FLOOR WILL BE BUTTED AGAINST THE BOTTOM OF THE TUB APRON, ALSO HOLDING THE TUB IN PLACE.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
752561-100 Rev. D
2776.XXXW SERIES
WHIRLPOOL/BATHING POOL

INSTALLATION INSTRUCTIONS

59-7/8
(1521mm)
WATER
RETENTION
FLANGE
(3 SIDES)
9
PUMP
ACCESS TO PUMP/MOTOR
(2) AIR VALVES
THROUGH REMOVABLE
(8) JETS
FRONT ACCESS PANEL
C/L OF
SHOWER ARM
FINISHED
WALL
C/L OF
VALVES
C/L OF
12
SPOUT
(305mm) OPT.
4
LEVELING STRINGER
(102 mm)
NOT FOR SUPPORT
19-3/4
(502mm)
1-1/2 N.P.T.M.
THREADS 2-3/4
(70mm)
4-5/8
(117mm)
59-7/8 x 32 x 20 (1521 x 813 x 508mm)
115 Lbs. (52 Kg.)
574 Lbs. (258 Kg.)
55 Gal. (208 L.)
45 Gal. (171 L.)
20 x 40 (508 x 1016mm)
26 x 53-1/2 (660 x 1359mm)
14-1/2 (368mm)
43 Lbs./Sq.Ft. (208 Kgs./Sq.m)
20.8
35.3
1.1 HP, 9.9 AMPS,120V.
THANK YOU...
for selecting an American Standard bath. Your new bath is
shipped to you after careful inspection. The whirlpool version
is completely assembled with pump, motor, and system
piping. All you need to finish the installation are your selected
fittings and electrical connections for a whirlpool.
14-3/4
To insure maximum performance and pleasure from this
(375mm)
product, please follow the instructions and cautions.
ON/OFF
SWITCH
List of Required Components (not included):
• Drain 1583.470*
* see your American Standard Distributor
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
UNDERSIDE
OF DECK
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping
damage. If such damage is found, report it to your vendor
immediately.
After inspection and during installation, protect the bath from
construction damage. Before installation, and before
enclosing with wallboard, tile, etc., water test the unit
and check for leaks.
If a whirlpool, do not make modifications to the whirlpool
system or remove pump from factory mounting. This could
adversely affect the safety and performance of the whirlpool
and void the warranty. Do not handle or move the whirlpool by
the pump, motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the
bath and must be ordered separately. Framing and enclosing
materials are provided by others.
IMPORTANT:
Water test unit before installation and enclosure!
THIS BATH IS NOT SELF-SUPPORTING AND MUST BE
• Bath Filler*
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 amp GFI
Outlet
• Cement, Plaster,
Grout
© American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.