Speck Swimming pool and SPA Pump Owner's Manual

Advertisement

OWNER'S MANUAL
Swimming Pool and Spa Pump
READ THIS MANUAL CAREFULLY
Important Notice:
use of this product. This information should be given to the owner and/or operator of this equipment.
WARNING: This product must be installed and serviced by a qualified pool professional, and must conform to all
national, state, and local codes.
WARNING: Before installing this product, read and follow all warning notices and instructions which are included.
Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Call
1-800-223-8538 or visit www.usa.speck-pumps.com for additional copies of these instructions.

IMPORTANT SAFETY INSTRUCTIONS

When installing and using this electrical equipment,
basic safety precautions should always be followed,
including the following:
READ AND FOLLOW
1.
ALL INSTRUCTIONS.
2. (For all units) WARNING - To reduce the risk of
injury, do not permit children to use this product unless
they are closely supervised at all times.
3. (For all permanently-installed units intended for
use on 15 or 20 ampere, 125 through 240 volt, single
phase branch circuits) WARNING - Risk of Electrical
Shock. Connect only to a branch circuit protected by
a ground-fault circuit interrupter (GFCI). Contact a
qualified electrician if you cannot verify that a circuit is
protected by a GFCI.
4. WARNING - To reduce the risk of electric shock,
replace any damaged cord immediately.
5. (For hot tub and spa pumps) Do not install within an
outer enclosure or beneath the skirt of a hot tub or spa.
6. (For permanently-installed pool or hot tub/spa
pumps) CAUTION - This pump is for use with
permanently-installed pools and may also be used
with hot tubs and spas if so marked. Do not use
with storable pools. A permanently-installed pool is
constructed in or on the ground or in a building such
that it cannot be readily disassembled for storage. A
storable pool is constructed so that it is capable of being
readily disassembled for storage and reassembled to
its original integrity.
BEFORE USING THE SPECK PUMP
This manual contains important information about the installation, operation and safe
7. (For all permanently-installed units intended for use
on 15 or 20 ampere, 12 through 240 volt, single phase
branch circuits) The unit must be connected only to a
supply circuit that is protected by a ground-fault circuit-
interrupter (GFCI). Such a GFCI should be provided by
the installer and should be tested on a routine basis. To
test the GFCI, push the test button. The GFCI should
interrupt power. Push the reset button. Power should
be restored. If the GFCI fails to operate in this manner,
the GFCI is defective. If the GFCI interrupts power
to the pump without the test button being pushed, a
ground current is flowing, indicating the possibility of an
electric shock. Do not use this pump. Disconnect the
pump and have the problem corrected by a qualified
service representative before using.
8. TO REDUCE RISK OF ELECTRICAL SHOCK,
A copper bonding connector (8 AWG) is provided for
bonding the motor to all metal parts of the swimming
pool, spa, or hot tub structure and to all electrical
equipment, metal conduit, and metal piping within 5
feet of the inside walls of a swimming pool, spa, or
hot tub, when the motor is installed within 5 feet of the
inside walls of the swimming pool, spa, or hot tub.
NOTE: To installer and/or operator of the Speck
Swimming Pool Pump; the manufacturer's warranty
will be voided if the pump is improperly installed and/
or operated.
SAVE THESE
9.
INSTRUCTIONS!

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Swimming pool and SPA Pump and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Speck Swimming pool and SPA Pump

  • Page 1: Important Safety Instructions

    WARNING: Before installing this product, read and follow all warning notices and instructions which are included. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Call 1-800-223-8538 or visit www.usa.speck-pumps.com for additional copies of these instructions. IMPORTANT SAFETY INSTRUCTIONS 7.
  • Page 2 SECTION 1 EQUIPMENT OPERATION AND MAINTENANCE 1/1 LOCATION 5. Before starting the pump for the first time, remove the see-through lid. (Turn lid ring counterclockwise to remove.) 1. Locate the pump as close to the pool as practical. Fill strainer tank with water until it is level with the suction Consult local codes for minimum distance between pool Replace lid with locking ring.
  • Page 3: Section 1 Equipment Operation And Maintenance

    SECTION 1 EQUIPMENT OPERATION AND MAINTENANCE 1/4 WINTERIZING - continued 1/3 MAINTENANCE - continued WARNING: Before servicing the pump, switch off the CAUTION: Allowing the pump to freeze will cause circuit breakers at the power source. Severe personal injury or death may occur if the pump starts while your severe damage and void the warranty.
  • Page 4: Section 3 Servicing Information

    Replacement parts may be available from your installer. When calling the manufacturer regarding a question or Call, fax, or write: Speck Pumps at 8125 Bayberry Road, problem with your pump, please have the serial number available. The serial number is located on the pump either Jacksonville, Florida 32256 Phone (904) 739-2626 Fax on the flange or motor labels.
  • Page 5: Section 4 Limited Warranty

    2. To the fullest extent permitted by law, the Limited Warranty will be void and of no force or effect and Speck Pumps - Pool Products, Inc.
  • Page 6 SECTION 4 LIMITED WARRANTY - continued 5. TO THE FULLEST EXTENT PERMITTED BY LAW, IN NO EVENT SHALL SPECK PUMPS - POOL PRODUCTS, INC. OR ITS OFFICERS, DIRECTORS, EMPLOYEES, SHAREHOLDERS, AGENTS, OR REPRESENTATIVES BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES OR LOSS, INCLUDING...

Table of Contents