Gianni Industries DG-600H Specifications

Features
Allow up to 600 proximity cards and PIN codes
RF Frequency: EM-400x 125 KHz
Tamper switch and alarm buzzer included
Fully Programmable via keypad and master code
Access mode selectable: card only card or PIN card+PIN
Support Wiegand 26/44-bit format auxiliary reader
Logical memory to prevent duplication
Invalid PIN Lock-out
Beeper sound
Non-Volatile Memory
Removable memory chip replacement
Statement
DG-600H stand-alone Proximity Reader is ideal for
single-door access control. It may connects to another reader
and serve as a controller. DG-600H enables the beeper to go
off whenever the keypad is pressed. A tamper switch is used to
protect the reader from external damage by linking the relay to
the alarming system. This model communicates in Wiegand
protocol and has a set of 600 proximity cards set to 26~37-bit
or 26-bit. (For DG-600E, proximity cards are set to either 26 or
44 bit.) It takes the reader 0.5 seconds at most to read a
proximity card or 5-digit PIN code. The built-in non-volatile
memory preserves the PINs for as long as 10 years. Even
when the power fails, the stored PIN codes will not be washed
away.
Warranty
The product is warranted against defects in material and
workmanship while used in normal service for a period of 1
year from the date of sale to the original customer. The GEM
policy is one of continual development and improvement;
therefore GEM reserves the right to change specifications
without notice.
Copyright © Gianni Industries, Inc. All rights reserved.
DM-CA-DG-600H Ver. E Published on 2010.12.20
DG-600H
Stand-alone Proximity Reader
7 0
1
2
3
4
5
6
7
8
9
*
0
#

Specifications

Operating Voltage: 9VDC to 16VDC
Current Draw: Average 50mA, Peak 100mA/12VDC
Transmitting Frequency: 125 KHz,
Memory Volume: 600 Proximity cards/tokens and PIN codes
Read Range: Up to 10 cm (Depending on local installation
conditions)
Keyboard: 12 digits keypad (0~9, *, #)
Input: Request-to-exit, door reed switch, auxiliary reader
Relay rating: 2A MAX/30VDC, 0.4A/120VAC
Invalid PIN Lock-out: The system will shut down for 60
seconds After the attempt to read the master or PIN cards
has faiiled for over 8 times. (No beeper signal when pressing
on the keypad)
Relocking timer:
Strike Time: 1~99 seconds (adjustable)
Strike mode: Access Timer or Latch
Alarm Function:
Door Held Open Alarm: 10~99
Door Forced Alarm
Panel Temper Alarm
Auxiliary Reader Format: Wiegand 44 or 26-bit only format
(adjustable), hexadecimal (Em 64-bit standard R/O or
compatible)
Case Material: ABS (UL94V0)
Color: Dark gray/ Beige White
Operating Temperature: -20~+70°C
A m b i e n t H u m i d i t y : 5 ~ 9 5 % r e l a t i v e h u m i d i t y ( n o n -
condensing)
Visual Signals:3 LED display with audible Indication
(Red/Yellow/Green)
EMC: Meet CE requirement
EMC: Meet CE requirement
GIANNI INDUSTRIES, INC.
No. 13, Zhongxing Rd., Tucheng Dist., New Taipei
City 236,Taiwan (R.O.C.)
Tel: 886-2 2267 7986 / Fax: 886-2 2267 9876
E-Mail: inquiry@gianni.com.tw
Website: gianni.tw
5
7 .
1 2
Unit: mm