Page of 10

Grizzly T10809 Instructions Manual

Wood lathe chuck set.
Hide thumbs
   
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Introduction
The T10809 3
" Wood Lathe Chuck Set includes
3
4
a scroll chuck with four self-centering bottom jaws
and five top jaw sets to provide a variety of grip-
ping needs for your wood turning projects.
Chuck Body Diameter ...................................3
Chuck Bore ...........................................1" x 8 TPI
Outside Grip Range:
— #1 Step Jaws ............................
— #2 Round Jaws ......................... 1
— #3 Round Jaws ............................ 3"–4
— Pin Jaws ......................................
Inside Grip Range:
— #1 Step Jaws (Upper Step) .............
— #1 Step Jaws (Lower Step) ....... 1
— #2 Round Jaws ......................... 1
— #3 Round Jaws .........................3
— Pin Jaws ....................................... 1"–2
Flat Jaws Maximum Outside Diameter .........5
Flat Jaws Minimum Inside Diameter .............2
Woodworm Required Hole ..................
To prevent personal injury, always under-
stand and follow all safety instructions in
your wood lathe owner's manual.
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
3
32
1
4
3
8
1
2
3
4
1
2
" x 1
5
16
COPYRIGHT © DECEMBER, 2013 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
#TS16160 PRINTED IN CHINA
WOOD LATHE CHUCK SET
Inventory
Description:
A. T-Handle Hex Wrench 4mm ....................... 1
B. Lathe Chuck Key 8mm Chrome ................. 1
C. Woodworm Screw ...................................... 1
D. Chuck Body ................................................ 1
E. #2 Round Jaws ........................................... 4
F.
Pin Jaws ..................................................... 4
"
3
G. Grip Studs 18mm, M6-1 x 6 ....................... 8
4
H. Flat Jaws .................................................... 4
I.
#1 Step Jaws .............................................. 4
"– 1
"
3
J.
Grip Studs 13mm, M6-1 x 6 ....................... 8
8
"–2
"
1
K. Flat Head Cap Screws M5-.8 x 8 ............... 8
2
"
1
L. #3 Round Jaws ........................................... 4
4
"–1
"
3
M. Hex Wrench 4mm ....................................... 1
4
"–2"
3
4
"–2
"
7
8
"–3
"
1
8
"–4
"
7
8
A
"
3
8
"
1
8
"
7
8
"
1
4
M
MODEL T10809
INSTRUCTIONS
B
C
G
H
L
K
Qty
D
E
F
I
J

Advertising

   Related Manuals for Grizzly T10809

   Summary of Contents for Grizzly T10809

  • Page 1: Specifications

    MODEL T10809 WOOD LATHE CHUCK SET INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Introduction Inventory The T10809 3 ⁄ " Wood Lathe Chuck Set includes Description: a scroll chuck with four self-centering bottom jaws A.

  • Page 2

    SAFE CLEARANCES. Before starting spindle, SANDING/POLISHING. To reduce entanglement verify workpiece has adequate clearance by hand- risk, remove tool rest before sanding. Never com- rotating it through its entire range of motion. pletely wrap sandpaper around workpiece. Model T10809 Wood Lathe Chuck Set...

  • Page 3

    Always make sure this set screw is properly the maximum chuck clamping diameter is not installed and tightened when using the chuck. exceeded. Model T10809 Wood Lathe Chuck Set...

  • Page 4

    Fully tighten cap screws—do not overtighten. Check jaw alignment. They should be evenly up against one another with no gaps and even in height. — If this is not the case, repeat this procedure until they are. Model T10809 Wood Lathe Chuck Set...

  • Page 5

    #3 Round Jaws When mounting workpiece on jaws, do not contact workpiece with the lower flat of jaws. This provides better gripping power and avoids any inconsistencies between surfaces that would interfere with true rota- tion. Model T10809 Wood Lathe Chuck Set...

  • Page 6

    Tenon Grip Recess Grip marring the workpiece. Outside Grip Range ....... ⁄ "–1 ⁄ " Inside Grip Range ........1"–2 ⁄ " Pin Jaws (2 jaws removed for clarity) Inside Recess Grip Small Diameter Workpiece Model T10809 Wood Lathe Chuck Set...

  • Page 7

    — Lower Step ........ 1 ⁄ "–2 ⁄ " Step Jaws (2 jaws removed for clarity) (Top View) Grip Inside Stud Recess Grip Outside Grip (Side View, Outside Grip) Grip Stud (Side View, Inside Grip) Model T10809 Wood Lathe Chuck Set...

  • Page 8

    Thread the workpiece onto the screw until it is center of chuck. seated firmly against the chuck. Remove jaws one by one as they disengage from the scroll gear. Model T10809 Wood Lathe Chuck Set...

  • Page 9

    Replace the back plate before using chuck in operations. Model T10809 Wood Lathe Chuck Set...

  • Page 10

    Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.

Comments to this Manuals

Symbols: 0
Latest comments: