1. Manuals
  2. Brands
  3. Campbell Manuals
  4. Switch
  5. HUB-SDM8
  6. Instruction manual

Campbell HUB-SDM8 Instruction Manual

Hide thumbs

Advertisement

Table of Contents

HUB-SDM8
1/08
C o p y r i g h t
©
2 0 0 4 - 2 0 0 8
C a m p b e l l
S c i e n t i f i c ,
I n c .

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HUB-SDM8 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Campbell HUB-SDM8

Summary of Contents for Campbell HUB-SDM8

  • Page 1 HUB-SDM8 1/08 C o p y r i g h t © 2 0 0 4 - 2 0 0 8 C a m p b e l l S c i e n t i f i c ,...

  • Page 2: Warranty And Assistance

    Warranty and Assistance The HUB-SDM8 is warranted by CAMPBELL SCIENTIFIC, INC. to be free from defects in materials and workmanship under normal use and service for twelve (12) months from date of shipment unless specified otherwise. Batteries have no warranty. CAMPBELL SCIENTIFIC, INC.'s obligation under this warranty is limited to repairing or replacing (at CAMPBELL SCIENTIFIC, INC.'s option) defective products.
  • Page 3 4. Installation and Wiring ..........2 4.1 Wiring SDM Devices and Power Wires for Daisy-Chain ......2 5. HUB-SDM5..............3 6. Generic Junction Box..........3 7. Maintenance ..............4 Figures 1. HUB-SDM8 in a Daisy-Chain Network.............2 2. HUB-SDM8 in a Daisy-Chain Network — Bottom View ......3...
  • Page 4 This is a blank page.
  • Page 5 The HUB-SDM8 is comprised of an environmental enclosure with eight compression fittings (two larger for 16 AWG power wires) and eight terminal strips. The HUB-SDM8 can also be used as a generic junction box, or as a HUB-SDM5. 2. HUB-SDM8 Specifications Terminal Strips: Three spring-loaded “guillotine”...

  • Page 6: Installation And Wiring

    HUB-SDM8 4. Installation and Wiring A U-bolt is used to mount the HUB-SDM8 to a 1.25 inch NPT pipe. The spring-loaded guillotines are opened with a small flat blade (2.5 x 50 mm) screwdriver (p/n 8125). Orient the screwdriver blade so that the blade edge is perpendicular to the orange separators.

  • Page 7: Generic Junction Box

    FIGURE 2. HUB-SDM8 in a Daisy-Chain Network — Bottom View 5. HUB-SDM5 The HUB-SDM8 can provide the same function as the HUB-SDM5, which is a 5-channel hub for SDM peripherals. Use the supplied plugs to seal the unused bulkhead fittings to use the HUB-SDM8 to connect multiple SDM devices to a single Campbell Scientific, Inc.

  • Page 8: Maintenance

    HUB-SDM8 7. Maintenance There are no user-serviceable parts in the HUB-SDM8. Make sure that all unused bulkhead fittings are sealed with a plug and that the lid is tightly fastened.
  • Page 9 This is a blank page.
  • Page 10 Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com info@campbellsci.com Campbell Scientific Africa Pty. Ltd. (CSAf) PO Box 2450 Somerset West 7129 SOUTH AFRICA www.csafrica.co.za cleroux@csafrica.co.za Campbell Scientific Australia Pty. Ltd. (CSA)

Table of Contents