Advertisement
Rear spacers
In the bag with the documentation, there are two
spacers which must be fitted in the two top
corners.
Fit the spacers into the holes, taking care to ensure
that the arrow (A) is positioned as shown in figur.
Then turn them through 45¡ (arrow (A) vertical) until
they lock into place.
Door reversibility
Unplug the appliance from the power supply before
carrying out the below-mentioned operations.
1. Unscrew the bottom hinge (A) and feets (B).
2. Remove the freezer door by releasing it from the
middle hinge (H).
3. Unscrew the middle hinge.
4. Remove the fridge door by releasing it from the
top hinge pin (G).
5. Remove the pin (G) from the top hinge, then
mount these on the opposite side, after having
removed the plugs which must be refitted on the
other side.
6. Refit the fridge door.
7. Replace the middle hinge to the left hand side.
8. Replace the freezer door.
9. Refit the bottom hinge and feets on the opposite
side.
10 Unscrew the handles. Refit them on the opposite
side after having pierced the plugs with a punch.
Cover the holes left open with the plugs
contained in the documentation pack.
To line up the doors, it is possible to adjust the
middle hinge (H) horizontally by means of a tool,
after slackening the two screws (see figure).
Warning:
After having reversed the opening direction of
the doors check that all the screws are properly
tightened and that the magnetic seal adheres to
the cabinet. If the ambient temperature is cold (i.e.
in Winter), the gasket may not fit perfectly to the
cabinet. In that case, wait for the natural fitting of the
gasket or accelerate this process by heating up the
part involved with a normal hairdrier.
20
A
45°
PR60
G
H
B
A
B
PR220
off frost or ice. Frost may be removed by using a
plastic scraper. Under no circumstances should
solid ice be forced off the liner. Solid ice should
be allowed to thaw when defrosting the
appliance. See defrost instructions.
¥
Do not place carbonated or fizzy drinks in the
freezer as it creates pressure on the container,
which may cause it to explode, resulting in
damage to the appliance. Do not use a
mechanical device or any artificial means to
speed up the thawing process other than those
recommended by the manufacturer. Never use
metal objects for cleaning your appliance as it
may get damaged.
Installation
¥
During normal operation, the condenser and
compressor at the back of the appliance heat up
considerably. For safety reasons, minimum
ventilation must be as shown in the relevant
Figure.
Attention: keep ventilation openings clear of
obstruction.
¥
There are working parts in this product which
heat up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
CONTENTS
Warnings .................................................................................................................................................12
Use - Cleaning the interior - Operation - Temperature regulation - Ambient switch - Fresh food ...............
refrigeration- Freezing fresh food - Storage of frozen food - Ice-cube production - Thawing.........................14
Use - Movable shelves - Positioning the door shelves - Bottle holder - Freezing calender .........................15
Hints - Hints for refrigeration - Hints for freezing - Hints for storage of frozen food.....................................16
Maintenance - Periodic cleaning - Periods of no operation - Interior light - Defrosting ............................17
Customer service and spare parts -Technical information ................................................................18
Installation - Location - Electrical connection...........................................................................................19
Installation - Rear spacers - Door reversibility .........................................................................................20
installation instructions.
¥
Parts which heat up should not be exposed.
Wherever possible the back of the product
should be against a wall.
¥
If the appliance has been transported
horizontally, it is possible that the oil contained in
the compressor flows in the refrigerant circuit. It
is advisable to wait at least two hours before
connecting the appliance to allow the oil to flow
back in the compressor.
Environment Protection
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid damaging
the cooling unit, especially at the rear near the
heat exchanger. Information on your local
disposal sites may be obtained from municipal
authorities. The materials used on this appliance
marked by the symbol
are recicable.
13
Advertisement
