Advertisement
MEMORY TUNING
You can store up to 10 stations each in the AM, FM1, and FM2 band
memories.
1. Repeatedly press
RADIO ON/OFF/BAND/MODE
band appears (AM, FM1, or FM2).
FH;I;J
FH;I;J
FH;I;J
FH;I;J
If
appears, hold down
about 2 seconds until it disappears.
2. Press
or
to reach the desired station.
UP
DOWN
3. Hold down
RADIO ON/OFF/BAND/MODE
FH;I;J
FH;I;J
FH;I;J
FH;I;J
until
appears.
4. Hold down one of the preset buttons (
The selected preset number appears and the radio stores the
station.
Note: To store stations in preset numbers 6–10, press
hold down the appropriate preset button for about 2 seconds.
For example, to store a station in preset number 6, press
then hold down
.
1
5. Repeat Steps 1–4 to store more stations.
To replace a station you stored, simply store a new station in that
preset number.
SELECTING STORED STATIONS
1. Repeatedly press
RADIO ON/OFF/BAND/MODE
desired band.
2. Continue to hold down
RADIO ON/OFF/BAND/MODE
FH;I;J
FH;I;J
FH;I;J
FH;I;J
seconds until
appears.
3. Press a preset button (
–
) to select a stored station. To select pre-
1
5
set numbers 6–10, press
+5
Note: If you hold down the preset buttons for more than about a sec-
ond, the currently tuned station will be preset to that button.
USING HOLD
locks the cassette player's radio function buttons and
HOLD
so you cannot accidentally change them. To lock the buttons, slide
in the direction of the arrow.
HOLD
To unlock the buttons, slide
HOLD
LOADING A CASSETTE TAPE
Use only Type I (normal bias) tapes.
1. Take up any slack in the tape by turning the cassette's hub with
a pencil. Do not touch the exposed tape.
2. Open the compartment door by pulling it toward you.
3. Insert a cassette into the door's tape guides with the cassette's
open edge facing up and the desired side facing the compart-
J J J J /PLAY
ment door. The arrow on
4. Close the cassette compartment door.
PLAYING A TAPE
1. If the radio is on, turn it off by repeatedly pressing
until the display turns off.
OFF/BAND/MODE
J J J J /PLAY
2. Press
. The battery indicator and
tape begins to play.
until the desired
RADIO ON/OFF/BAND/MODE
for about 2 seconds
–
) for about 2 seconds.
1
5
, then
+5
to select the
for about 2
then the appropriate preset button.
S-BASS
>EB:
>EB:
>EB:
>EB:
flashes for several seconds.
in the opposite direction.
indicates the playback direction.
RADIO ON/
J7F;
J7F;
J7F;
J7F;
appear and the
3. Adjust
to a comfortable listening level.
VOL
4. To emphasize bass sounds, repeatedly press
87II
87II
87II
87II
appears. Press
5. To stop the tape, press ' ' ' '
6. While the tape is stopped, press
,
and
(fast-forward) to fast-forward it. To stop the tape before it
for
reaches the end, press ' ' ' '
Notes:
,
are not released at the end of the tape. Press ' ' ' '
# # # #
•
and
to release them.
STOP
• To prevent tape damage, press ' ' ' '
TAPE TIPS
We do not recommend long-play cassette tapes such as C-120s be-
cause they are thin and can easily tangle.
,
+5
Restoring Tape Tension and Sound Quality
After you play a cassette tape several times, the tape might become
tightly wound on the reels. This can cause playback sound quality to
deteriorate.
To restore the sound quality, fast-forward the tape from the begin-
ning to the end of one side, then completely rewind it. Then loosen
the tape reels by gently tapping each edge of the cassette on a flat
surface.
Caution: Be careful not to damage the cassette when tapping it. Do
not touch the exposed tape or allow any sharp objects near the cas-
sette.
CARE
Keep the cassette player dry; if it gets wet, wipe it dry immediately.
Use and store the cassette player only in normal temperature envi-
ronments. Handle the cassette player carefully; do not drop it. Keep
the cassette player away from dust and dirt, and wipe it with a damp
cloth occasionally to keep it looking new.
Modifying or tampering with the cassette player's internal compo-
nents can cause a malfunction and might invalidate its warranty and
void your FCC authorization to operate it. If your cassette player is
not performing as it should, take it to your local RadioShack store for
assistance.
CLEANING THE
TAPE-HANDLING PARTS
Dirt, dust or particles of the tape's coating can accumulate on the
tape heads and other parts that the tape touches. This can greatly
reduce the performance of the cassette player. After every 20 hours
of tape player operation, follow these steps to clean the tape-han-
dling parts or use a RadioShack cassette deck cleaning kit.
1. Remove the batteries.
2. Open the cassette compartment door and press J J J J
expose the tape-handling parts.
3. Use a cotton swab dipped in denatured alcohol or tape head
cleaning solution to clean the tape head, tape guide, pinch
roller, and capstan.
3
S-BASS
again to turn it off.
S-BASS
.
/STOP
# # # #
(rewind) to rewind the tape
.
/STOP
before playing the radio.
/STOP
I# I# I# I#
until
/
to
/PLAY
Advertisement
