en Table of contents Intensive zone Safety instructions Extra drying Delivery Energy Save Installation In daily use Washing the dishes Children in the household Programme data Door lock Aqua sensor Damage Zeolith drying Disposal Switching on the appliance Remaining running time display Getting to know your appliance Display window Control panel...
ã= Safety instructions Warning Knives and other utensils with sharp points must be placed in the cutlery basket with the points downwards or horizontally on the knife shelf *. Delivery * depending on model Check the packaging and dishwasher immediately for damage caused in transit.
Damage Getting to know your appliance The appliance may be repaired and opened up by a technician only. To do this, disconnect the Diagrams of the control panel and the interior of the appliance from the power supply. Pull out the appliance can be found in the envelope at the front.
Overview of menu To change the language: Open the door. The settings can be found in the individual chapters. Switch on ON/OFF switch (. Water Hardness Hold down programme button # and press Intensive drying START button )" until the digital display 8 Rinse aid : ...
Water hardness table Water softening system :DWHU +DUGQHVV PPROO 6HW YDOXH KDUGQHVV UDQJH RQ WKH To ensure good washing results, the dishwasher YDOXH PDFKLQH &ODUNH requires soft water, i.e. containing low amounts of ¯¯ VRIW lime, otherwise white limescale will be deposited on ¯³...
Switching off salt refill indicator/ Special salt $ water softening system If the salt refill indicator H is impaired (e.g. when using combined detergents containing salt Using special salt component), it can be switched off. Always refill with special salt immediately before Proceed as described under “Adjusting the water switching on the appliance.
Setting amount of rinse aid Rinse aid % The amount of rinse aid can be set from . Please set rinse aid on to obtain very As soon as the rinse-aid refill indicator P is lit on good drying results ( : is already set in factory).
Unloading the dishwasher Utensils To prevent water from dripping off the upper basket onto the utensils in the lower basket, it is recommended to empty the appliance from the bottom Not suitable Hot utensils are sensitive to shock! Therefore, when Cutlery and utensils made of wood.
Small accessories holder * Heavily soiled utensils (pans) should be placed in the * depending on model bottom basket. The more powerful spray jet provides a better dishwashing result. Light-weight plastic accessories, e.g. cups, lids, etc. can be held securely in the small accessories holder. Other examples, such as the best way of loading your dishwasher, can be found on our homepage as a free download.
Adjusting the height of the basket Removing the upper basket The height of the upper utensils basket 1* can be Pull out the top basket 1* all the way. adjusted in 3 stages to create more space either in the Lift the basket at the front and pull it over the upper or lower basket.
Adding detergent Detergent If the detergent dispenser 9: is still closed, press the lock 9B to open the detergent You can use tablets as well as powder or liquid dispenser. detergents for dishwashers, but never use washing Pour detergent into the dry detergent up liquid.
Combination detergent Notes You will obtain optimum rinsing and drying results Apart from conventional detergents (Solo), a number by using solo detergents and applying salt and of products are offered with additional functions. rinse aid separately. These products contain not only the detergent but also rinse-aid and salt replacement substances (3in1) If programmes are short, tablets may not have full and, depending on the combination (4in1, 5in1, etc.),...
Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia. Type of utensils Type of soiling Programme Possible addi- Programme sequence tional options pots and pans, non-sensitive very adhesive ¹...
Additional options Washing the dishes * depending on model Programme data Additional options can be set with the buttons h. The programme data (consumption values) can be found in the summary of instructions. They refer to ¥ normal conditions and the water hardness set value Turbo * .
Switching on the appliance Timer programming Turn on the tap fully. You can delay the start of the programme in 1 hour steps up to 24 hours. Open the door. Open the door. Switch on ON/OFF switch (. Switch on ON/OFF switch (. The display of the last selected programme flashes.
Automatic switch off after end of Switching off the appliance programme or interior light* Short time after the end of the programme: * depending on model Open the door. To save energy, the dishwasher can be automatically Switch off ON/OFF switch (. switched off 1 min or 120 min after the programme Turn off the tap (not applicable if Aqua-Stop ends.
Changing the programme Maintenance and care When the START button )" has been pressed, the programme cannot be changed. A regular inspection and maintenance of your machine will help to prevent faults. This saves time and The only way a programme can be changed is by Cancel programme (Reset).
Filters Spray arms The filters 1j keep large foreign objects in the Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine Check outlet nozzles on the spray arms for filter and a microfilter.
Waste water pump Troubleshooting Large food remnants in the rinsing water not retained by the filters may block the waste water pump. The The majority of faults which could occur in daily rinsing water is then not pumped out and covers the operation can be rectified by the user.
... changing settings Water is left in the appliance at the end of the programme. A setting cannot be changed, a programme starts. ) Waste water hose Wrong programme button pressed. Terminate the is blocked or kinked. programme (see chapter entitled “Terminating the programme (Reset)”) and start all over again.
... on the utensils Streaks on glasses and cutlery, glasses have metallic appearance. Food residue on the utensils. Too much rinse aid. Utensils placed too closely together, utensils Plastic parts discoloured. basket overfilled. Too little/unsuitable detergent. Too little detergent. Too weak programme selected. Rinse programme too weak.
Customer service Installation If the advice given does not resolve your problem, The dishwasher must be connected correctly, please contact your customer service. Contact details otherwise it will not function properly. The can be found on the back cover of this instruction specifications for the inlet and outlet as well as the manual or in the enclosed customer service list.
Installation ã= Warning The required installation dimensions can be found in If the appliance is not in a cavity and a side panel is the installation instructions. Level the appliance with accessible, the door hinge area must be covered at the aid of the height-adjustable feet.
Warm water connection * Electrical connection * depending on model Connect the appliance to an alternating current only, ranging from 220 V to 240 V and 50 Hz or The dishwasher can be connected to cold or hot water 60 Hz via a correctly installed socket with up to max.
Transportation Waste disposal Empty the dishwasher and secure loose parts. Drain the appliance according to the following Both the packaging of new appliances and the old appliances themselves contain valuable raw materials steps: and recyclable materials. Turn on the tap. Please dispose of the individual parts separated Open the door.