Advertisement
Quick Links
pressUre bleed
accessory kIt
Model MVp6000
User's ManUal
Have a technical question?
americas:
If you have questions, or require technical service, please
contact our trained service technicians at:
1-314-679-4200 ext. 4782
Monday – Friday 7:30 am to 4:15 pm CST
Visit our web site at www.mityvac.com for new products,
catalogs, and instructions for product use.
Need service parts?
To order replacement or service parts, visit us online at
www.mityvacparts.com or call toll free 1-800-992-9898.
Specifications:
Reservoir Capacity (w/ pump): 1 quart/1 liter
Maximum Pressure:
20 psi/1.4 bar/140 kPa
It is the responsibility of the user of this equipment to read this user's manual entirely,
and understand the safe and proper use and application of this equipment.
MV103-1
marcH 2011
Form 824889
Section -
Advertisement
Summary of Contents for Matco Tools MVP6000
- Page 1 Model MVp6000 User’s ManUal Have a technical question? americas: If you have questions, or require technical service, please contact our trained service technicians at: 1-314-679-4200 ext. 4782 Monday – Friday 7:30 am to 4:15 pm CST Visit our web site at www.mityvac.com for new products,...
- Page 2 table oF contents Service Parts & Accessories ......3 Pressure Bleed Adapter Chart ......4 Principal of Operation .
-
Page 3: Service Parts & Accessories
serVIce parts & accessorIes MVA6850 – Pressure Bleed Adapter Kit MVA6839 – Pressure Bleed Reservoir serVIce/replaceMent parts and kIts part/kIt nUMbers ref. description 824820 824821 824822 824823 824824 MVA570 MVA7210 824461 Cap with Chain 1 pc Cap Seal 1 pc 1 pc 8’... -
Page 4: Pressure Bleed Adapter Chart
pressUre bleed adapter cHart pressure cap system adapter # type application(s) MVA800* Locking collar Toyota, Lexus MVA801* 3-Tab camlock Chrysler, Dodge, Jeep, Plymouth 3-Tab camlock Chrysler, Dodge, Jeep, Plymouth MVA802* MVA803* 3-Tab camlock Most late model GM cars (Buick, Cadillac, Chevrolet, GMC, Hummer, Oldsmobile, Pontiac) Some Mazda MVA804* 45 mm thread... -
Page 5: Principal Of Operation
prIncIpal oF operatIon This equipment is designed and intended for expelled. When operating this equipment, use use as an accessory to dispense or evacuate common sense, and always stop to think before fluids using a Matco hand pressure/vacuum disconnecting a hose or other component. pump MVP5000 (sold separately). -
Page 6: Instructions For Use
InstrUctIons For Use Fluid dispensing 8. Once the proper amount of fluid has been dispensed, close the shutoff valve and 1. Unscrew the cap from the fluid transfer release the pressure in the system by acti- bottle, and fill to desired level with clean vating the pressure relief lever on the hand fluid. - Page 7 6. Insert the fluid wand into the reservoir from 3. Open fluid reservoir or brake lines carefully. which you intend to draw fluid, and open the Top off reservoir fluid and reconnect battery ball valve to allow the flow of fluid. cable when finished.
- Page 8 1. Ensure the vehicle is properly positioned d. Ensure the shutoff valve on the fluid hose for safe, convenient access to the master assembly is open, and operate the manual cylinder and the brake bleed screw located pump to pressurize the system to the rec- on each wheel brake cylinder.
- Page 9 mended pressure. Do not exceed 1.4 bar during bleeding. Make sure all the bleeding (20 psi) pressure. fittings are clean prior to beginning of the bleeding procedure. 11. Connect a bleed reservoir to the bleed note: Consult the vehicle manufacturer’s screw of the first cylinder to be bled.
- Page 10 8. Keep the bleed screw open and continue to Connect the ATF refill adapter to the trans- operate the vacuum pump as required until mission fill port; then connect the fluid hose new fluid is visibly flowing through the bleed extending from the bottom of the fluid trans- tube.