Hills series User Manual
Icon code pad
Hide thumbs
Also See for HILLS series:
- User manual (28 pages) ,
- User manual (24 pages) ,
- Owner's manual (16 pages)
Table of Contents
Related Manuals for Hills HILLS series
Summary of Contents for Hills HILLS series
- Page 1 HILLS Series Icon Code Pad ® User Manual...
-
Page 2: Introduction
INTRODUCTION This manual is provided to help you understand your security system and become proficient in its operation. All users of your security system should read and follow the instructions in this booklet and, if possible, practice on the keypad control while your professional installer is on site. -
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION........................2 WARNING NOTES ........................2 TABLE OF CONTENTS......................3 GLOSSARY OF TERMS......................4 ICON KEYPAD DISPLAY......................5 EMERGENCY ACTIVATION KEYS ..................5 UNDERSTANDING THE ICONS & LIGHTS ................6 KEYPAD FUNCTIONS ......................7 ADDING AND CHANGING USER CODES ................10 ASSIGNING USER CODE AUTHORITY LEVELS..............11 OTHER KEYPAD FUNCTIONS....................12 SERVICE MENU ........................14 KEYPAD CONTROL TONES (BEEPS)...................15... -
Page 4: Glossary Of Terms
GLOSSARY OF TERMS An option that allows a delay in reporting to the central Abort Delay station. The level of access an individual has when using an Authority Level alarm panel. The location where alarm data is sent during an alarm Central Station report. -
Page 5: Icon Keypad Display
ICON KEYPAD DISPLAY Listen-in Power Armed Ready ALARM Service Instant Enter Code Trouble FIRE Silenced Tamper 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 EMERGENCY ACTIVATION KEYS NOTES: You must hold these keys for 2 seconds to activate these functions. -
Page 6: Understanding The Icons & Lights
UNDERSTANDING THE ICONS & LIGHTS ARMED ICON The armed icon is “on” when the system is armed. The armed icon is “off” when it is disarmed. The armed icon will flash when there has been an alarm during the previous arm cycle. -
Page 7: Keypad Functions
PARTIAL LIGHT The partial light is “on” when all interior (motion detector) zones are bypassed. TAMPER/TROUBLE ICONS The tamper or trouble icon is on when a zone(s) is tampered or in trouble. Press [r]–[2] and refer to the Service Menu section on page 14 of this manual for further instructions. ZONE ICON The zone icons are “off”... - Page 8 ARMING YOUR SYSTEM IN THE “PARTIAL” MODE PARTIAL is used when the user is inside the premise and wants protection around the perimeter. Step 1 Close all protected doors and windows. • Ready icon must be on or flashing when all protected zones and sensors are secure.
- Page 9 CHANGING MODES WHILE SYSTEM IS ARMED • Pressing the [PARTIAL] key will turn on/off (toggle) a delay on entry/exit doors and turn on/off (toggle) the instant icon. • (Optional) Press the [BYPASS] key at this time to turn on/off (toggle) all designated interior zones.
-
Page 10: Adding And Changing User Codes
BYPASSING ZONES If you wish to bypass one or more zones, this must be done while the system is in the disarmed state. The following steps are used for bypassing zones: Step 1 Press the [BYPASS] key. Step 2 Enter user code, if required (optional). The bypass light flashes. Step 3 Enter 1 or 2 digits indicating the zone you wish to bypass, i.e. -
Page 11: Assigning User Code Authority Levels
ASSIGNING USER CODE AUTHORITY LEVELS Assign authority levels to users by following the steps below. Assign user codes before assigning authority levels. Step 1 Press [r]-[6]-[“Master Arm/Disarm Code”]. Note: someone changing the authority of another person can only add or remove partition authorization for partitions to which they have access. -
Page 12: Other Keypad Functions
OTHER KEYPAD FUNCTIONS SETTING THE KEYPAD TONE Step 1 Press [r]-[0]. Keypad is now in the “Adjust Tone” mode. Step 2 Pressing the [•] key will make the keypad sounder go to higher tones, pressing the [–] key will make the keypad sounder go to lower tones. Step 3 When the desired tone is reached, press the [#] key to set this tone and exit from the “Adjust Tone”... - Page 13 SET SYSTEM DATE Step 1 Press [r]-[9]-[6]. Enter Code icon will display. Step 2 Enter a [“Master Code”]. The service icon will appear flashing. Step 3 Enter the “Day of Week “ 1=Sunday 3=Tuesday 5=Thursday 7=Saturday 2=Monday 4=Wednesday 6=Friday Step 4 Enter the “Month Code”.
-
Page 14: Service Menu
SERVICE MENU The service icon will be “on” if the security system requires service. If the service icon is “on”, press [r]-[2] to determine the service condition. If a zone(s) is tampered, the tamper icon will flash and the zone icon(s) will be on. If a zone(s) is troubled, the trouble icon will flash and the zone icon(s) will be on. -
Page 15: Keypad Control Tones (Beeps)
KEYPAD CONTROL TONES (BEEPS) A sounder is built into the keypad. If programmed, your system keypad may sound for any of the following reasons: • Beeps for all key presses. • Sounds a continuous tone during the Entry delay time. •... -
Page 16: Emergency Evacuation Plans
EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition. For example, the following steps are recommended by the National Fire Protection Association and can be used as a guide in establishing an evacuation plan for your building. Draw up a floor plan of your home. - Page 17 (24) months from the date of purchase. If any defect appears during the warranty period return it to place of purchase. Hills Industries assumes no liability for consequential or indirect damage and accepts no responsibility for repairing damage to the product caused by misuse, careless handling, or where repairs have been made by others.
-
Page 18: Security System Notes
SECURITY SYSTEM NOTES Installing/Service Company _________________________________ For Service Call __________________________________________ Central Station ___________________________________________ Duress Code ____________________ This system is not partitioned. EMERGENCY ACTIVATION KEYS (check if enabled) Fire Auxiliary Emergency Police PROGRAMMED FUNCTIONS Abort Delay Cancel Alarm Forced Arming Auto Bypass Change Partitions Group Bypass Auto Instant... -
Page 19: Zone Descriptions
ZONE DESCRIPTIONS Icon Keypad Page 19... - Page 20 Hills Icon Code Pad User Manual 2007-01-09...