Related Manuals for JBL AEC65
Summary of Contents for JBL AEC65
-
Page 1: User Guide
Speakers Cat. Nos. AEC65 AEC80 AEI65 AEI80 AEM65 USER GUIDE AEC65 AEI65 AEM65 AEC80 AEI80 Dual Tweeter Ceiling Speaker In-Wall Speaker Stereo Ceiling Speaker PK-93410-10-00-2A... -
Page 2: Parts Included
Cat. Nos. AEI65 and AEI80 One pair of speakers with grilles. Template/Paint Shield. Remove paint shield (inner rectangle) at perforation. Cat. Nos. AEC65 and AEC80 One pair of speakers with grilles. Template/Paint Shield. Remove paint shield (inner rectangle) at perforation. -
Page 3: Speaker Placement
SPEAKER PLACEMENT Front Speaker Mounting WALL –60 Rear Speaker Mounting 5-6 ft. WALL WALL WALL WALL Ceiling Speaker Mounting Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible. These recommendations are for the optimum placement of the loudspeakers. Use these placement recommendations as a guide. -
Page 4: Speaker Connections
Hide the excess wire behind the wall. Speakers and electronics terminals have corresponding (+) and (–) terminals. Most manufacturers of speakers and electronics, including Leviton Architectural Edition powered by JBL, use Red to † † LEFT RIGHT denote the (+) terminal and Black for the (–) terminal. -
Page 5: Installation
TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS. NOTE: LEVITON/JBL IN-WALL AND CEILING SPEAKERS WERE DESIGNED TO BE EASILY INSTALLED. HOWEVER, IF YOU ARE UNSURE OF YOUR ABILITY TO PROPERLY INSTALL THESE LOUDSPEAKERS, PLEASE CONTACT YOUR DEALER OR A QUALIFIED INSTALLER. - Page 6 The tweeter will not swivel more than 15 degrees in any direction; do not attempt to force it to move further. You may also rotate the tweeter to orient the JBL logo as desired.
- Page 7 CEILING SPEAKER INSTALLATION – EXISTING CONSTRUCTION: Level ≥1/2" ≥1/2" ≥1/2" Template Step 3: Step 1: Step 2: Always allow at least one- Remove the grille from the Determine the correct half inch between a wall stud speaker frame by pulling on speaker location.
- Page 8 PAINTING THE SPEAKER FRAME AND GRILLE Leviton Architectural Edition powered by JBL loudspeakers can be painted to match any decor. If you wish to change their color, the satin finish on the grille and frame will function as a primer coat. Before painting, install the paint shield (inner section of template in the assembly kit) securely into the recess in the baffle.
-
Page 9: Troubleshooting
TROUBLESHOOTING IF THERE IS NO SOUND FROM ANY OF THE SPEAKERS: • Check that receiver/amplifier is on and a source is playing. • Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other. -
Page 10: Specifications
We do not recommend sustained operation at these maximum power levels. • * Trademark of Dolby Laboratories. DTS is a registered trademark of Digital Theater Systems, Inc. AEM65 AEC65 Frequency Frequency Response Response 40Hz–20kHz (+10dB) - Page 11 SPECIFICATIONS AEC80 AEI65 Frequency Frequency Response Response 32Hz–20kHz (+10dB) 38Hz–20kHz (+10dB) Recommended Maximum Recommended Maximum Amplifier Power † Amplifier Power † 100 watts 80 watts Impedance Impedance 8 ohms nominal 8 ohms nominal Sensitivity Sensitivity 89dB (2.83V/1m) 88dB (2.83V/1m) Crossover Frequency Crossover Frequency 3,000Hz 3,000Hz...
-
Page 12: Frequency Response
SPECIFICATIONS AEI80 Frequency Tweeter Response 1" Titanium-laminate 30Hz–20kHz (+10dB) dome, w/Elliptical Oblate Spheroidal waveguide Recommended Maximum and swivel mount Amplifier Power † 100 watts Plate Size (W x H) 10-1/8" x 13-1/8" (257mm x 333mm) Impedance 8 ohms nominal Mounting Cutout Size (W x H) 8-7/8"...