Generac Power Systems QT 5.4L Owner's Manual page 51

1 0D9913 16
2 0E9747
3 0F3514
4 0F3903C
0F3903C
5 0F2776A
6 0D5417
7 0F3844
8 * 029333A
9 022131
10 055596
11 057772
12 057823
13 057765
14 0F3534
15 069860E
16 049821
17 022129
18 039253
19 0D2244M
20 044118 REF
21 055934M
22 047411
23 071623
24 0D6742
25 022097
26 0F1820
27 0F1818
28 022473
29 048031J
30 0F2929
31 077996
32 046526
33 070008
34 070006 24
35 0D2608
36 0F5114
37 0F5454
41 047290
42 059057
* NOTE: I/N 8 IS FOR HOLDING SENSOR TO I/N 5.
SCREW SHC M8-1.25 X 35 SS
1 STARTER 12 VOLT
1 SPACER FLEXPLATE 5.4L/6.8L (1800 RPM ONLY)
1 FLEX PLATE 2 POLE 5.4L & 6.8L (1800 RPM UNITS ONLY)
2 FLEX PLATE 2 POLE 5.4L & 6.8L (3600 RPM UNITS ONLY)
1 BRACKET, SIGNAL CONDITIONER
8 SCREW HHC M10-1.0 X 25 G10.9
8 WASHER FLAT .43 X 1.00
1 TIE WRAP UL 7.4" X .19" BLK (NOT SHOWN)
1 WASHER FLAT 3/8-M10 ZINC
1 BARBED STR 3/8 NPT X 3/8
1 WASHER NYLON .565
2 CLAMP HOSE #10 .56 - 1.06
1 ADAPTER M14-1.50 X 3/8 NPT
2 HEAT SHLD EXHAUST MANIFOLD
1 HOSE DRAIN ASSY 28"
2 SCREW SHC M8-1.25 X 30 G12.9
4 WASHER LOCK M8-5/16
1 SCREW HHC M8-1.25 X 20 G8.8
1 ASSY MAGPICKUP(3/8-24 MALE)
BARBED STR 1/2 NPT X 5/8
1 CLAMP VINYL .75 X .343 Z
1 SCREW HHC M6-1.0 X 16 G8.8
4 SCREW SHC M10-1.5 X 55 G12.9
1 VALVE PCV (FORD 6.8L)
1 WASHER LOCK M6-1/4
2 MACHINED MANIFOLD EXHAUST 5.4L
2 GASKET EXHAUST MANIFOLD
1 WASHER FLAT 1/4-M6 ZINC
1 HOSE CLAMP BAND 5/8"
1 ENGINE ADAPTER 5.4L/6.8L
2 CAP HOSE
6 WASHER LOCK M10
8 WASHER FLAT M8 SS
WASHER LOCK M8 SSTL
8 SCREW HHC 5/16-18 X 1/2 SSTL
1 DECAL REFER TO OWNERS MANUAL
1 PLATE MAG PICK-UP ADAPTOR
1 HOSE 3/8 ID SINGLE BRAID (15" LG)
1 HOSE 3/4 ID SAE-30R2