Quick Start Guide - Gemini MPX-3 Operation Manual

VOLTAGE SELECTOR: To set the proper voltage, adjust the VOLTAGE SELECTOR (1) switch to 115 or 230 volts.
1
POWER JACK (AC IN): Connect the power plug into the POWER JACK (2) for power.
2
REMOTE CONTROL: Use the included CABLE & REMOTE CONTROL (3) to connect the REMOTE CONTROL to the
3
MAIN UNIT.
LINE OUTPUT JACKS: LINE OUTPUT JACKS (4) provide stereo sound via RCA cables to your MIXER or RECEIVER.
4
NOTE: MAKE SURE CABLES ARE PLUGGED IN TIGHT FOR OPTIMAL SOUND.
DIGITAL OUTPUT (BNC): Use the BNC (5) jack to connect to any type of device that accepts DIGITAL SIGNALS.
5
POWER: Press the POWER (6) button to turn on the CD player.
6
NOTE: MAKE SURE VOLTAGE SELECTOR SWITCH (1) IS SET BEFORE USE.
DISC TRAY: Put a CD in the DISC TRAY (7) after pressing OPEN/CLOSE (8); trays hold both 12 cm and 8 cm CDs.
7
OPEN/CLOSE: Tap OPEN/CLOSE (8) once to open the tray and again to close it.
8
DISPLAY: The DISPLAY (9) shows the various functions for the CD Player. See FUNCTION DESCRIPTIONS for details.
9
PLAYBACK DISPLAY BAR: The PLAYBACK DISPLAY BAR (10) shows the TIME ELAPSED and TIME REMAINING.
10
PLAY/PAUSE: Press PLAY/PAUSE (11) button to activate PLAY or PAUSE mode. See CUE or ROBO START
11
INSTRUCTIONS for details.
CUE/PREVIEW: Tap CUE/PREVIEW (12) to come back to a set CUE or press and hold to PREVIEW from a CUE,
12
refer to CUE INSTRUCTIONS.
SEARCH (FOLDER/FILE): Use the SEARCH (13) buttons to scan forward and reverse directions on a TRACK.
13
In MP3 mode use the FOLDER button to view which folder is being read and use the FILE button to view the file.
TRACK SEARCH: Press the TRACK SEARCH (14) buttons to select which TRACK to play.
14
TIME: Tap the TIME (15) button to switch the TIME preference in three modes: ELAPSED, REMAIN, TOTAL REMAIN.
15
STOP: Press STOP (16) once to stop the CD.
16
SINGLE: Tap SINGLE (17) for: SINGLE AUTO CUE, CONTINUOUS, and NORMAL modes.
17
FLY CUE: FLY CUE (18) sets a CUE POINT on the fly.
18
B/EXIT: Press B/EXIT (19) in PLAY mode, after a CUE POINT is memorized to start a LOOP, press again to exit LOOP.
19
B-EDIT: Press B-EDIT (20) and use the JOG WHEEL (22) to edit an existing LOOP, press again to exit EDIT mode.
20
RETURN: To play from a saved CUE POINT or a LOOP, press RETURN (21) to play the LOOP or the CUE again.
21
JOG WHEEL: The JOG WHEEL (22) has various functions: PITCH BEND, CUEING, and TRACK SEARCHING.
22
JOG MODE: Press to change the JOG MODE (23) of the JOG WHEEL (22) from MUSIC to TRACK mode.
23
JOG MODE LED: The
24
PITCH: The PITCH (25) button activates the PITCH CONTROL SLIDE (27)
25
PITCH BEND: Buttons for PITCH BEND (26), lower or raise the pitch percentage (- or +) 4% when pressed.
26
PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE (27) up or down will lower or raise the pitch
27
percentage (- or +) 4%, 8%, & 16%.
VPS (VARIABLE PITCH SELECTOR) 4%, 8% & 16%: Use the VPS (28) buttons use to change the PITCH settings
28
from 4%, 8%, & 16%.
ROBO START: Using ROBO START (29) enables you to alternate play between two CDs using both sides.
29

QUICK START GUIDE:

JOG MODE LED (24) displays which JOG MODE (23) is in use.
(3) (3)
(3) (3) (3)