1. Manuals
  2. Brands
  3. POSX Manuals
  4. Barcode Reader
  5. xi3000
  6. User manual

POSX xi3000 User Manual

Bluetooth scanner
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
WARNING
Xi3000 Bluetooth Scanner
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try correcting the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
If applicable, as below
FCC Caution: To assure continued compliance, (example – use only shielded
interface cables when connecting to computer or peripheral devices). Any changes
or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator & your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
User's Manual
may cause undesired operation.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the xi3000 and is the answer not in the manual?

Questions and answers

Related Manuals for POSX xi3000

Summary of Contents for POSX xi3000

  • Page 1 WARNING Xi3000 Bluetooth Scanner This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 2: Table Of Contents

    Windows XP with Service Pack2 ............ 15 2.4.3 DC Jack.....................5 5.2.2 Belkin Bluetooth Driver ..............17 ..................5 NTERFACE ETTING BLUETOOTH HID ..................22 GENERAL FEATURES ................6 Xi3000 ................22 ONFIGURING ......................6 UZZER 6.1.1 Activate Bluetooth HID Interface ........... 22 ....................6 NDICATOR 6.1.2 Reset Connection ................23 .....................6...
  • Page 3 EQUENCE .............39 ND OF ORMAT ROGRAMMING ............39 CTIVATE DITING ORMATS 9.10 ..............40 XCLUSIVE DITING 9.11 ..............40 ROGRAMMING XAMPLES CONFIGURING YOUR Xi3000-BT............41 10.1 ..............41 NTER ONFIGURATION 10.2 ....................41 EFAULT 10.3 ...................41 ETTING 10.4 ..............42 ETTING ARAMETER ALUES 10.4.1 Numeric Parameters ...............42 10.4.2...

  • Page 4: Introduction

    Note: Please refer to chapter 5 Bluetooth Serial Port for The Xi3000-BT is one of the most versatile and flexible wireless barcode scanners available today. The Xi3000-BT contains all the features and functions required for Bluetooth Serial Port installation and configuration up to date barcode reading.

  • Page 5: Setup Rf C

    2.2 Power Up the Xi3000-BT 2.4 Charging your Xi3000-BT When you receive your Xi3000-BT, the battery is separated from Xi3000-BT. There are three methods to charge the battery. Placing the scanner on the base, Please insert the battery into the bottom of the scanner and lock the battery by inserting the battery in front of the base or inserting the power supply into the DC pushing the clip to power on the scanner.

  • Page 6: General Features

    3. General Features 2.4.3 DC Jack 3.1 Buzzer The buzzer of the scanner beeps differently to indicate various operating conditions. • Power On Beep: The scanner will issue a long beep to indicate a successful power on. • Good Read Beep: The system provides four volume levels and four beeping Insert the power supply to the DC Jack at bottom of the scanner.

  • Page 7: Auto-Sense

    • Continuous Mode: The scanner is always scanning. 3.5 Re-read Delay • Auto Power Off Mode: The scanner will start scanning once the switch is triggered. The scanning continues until a preset scanning period (Scanner If the scanner mode is set to Continuous, Auto Power Off, Alternate, or Momentary Time-Out Duration) is expired.

  • Page 8: N Egative B Arcodes

    • EAN13 (with or without Add-on) • Code 93 • Code 128 The Xi3000-BT is a multi-interface scanner. It can be used as a keyboard wedge • EAN 128 scanner, an RS-232 scanner, or a USB scanner. The output interface can be programmed using the setup barcodes in this manual.

  • Page 9: Usb Interface

    The inter-character delay is zero by default. The Xi3000-BT reserves 4 KB flash memory as transmit buffer when the scanner is out of service range. Data will be saved into the reserved buffer when the...
  • Page 10 The Xi3000-BT can work offline and store the reading data into the internal Flash The Xi3000-BT can be configured to the standard Bluetooth Serial Port as the data memory for later upload to the host.

  • Page 11: C Onfiguring B Luetooth D Evice D River

    Please follow the procedures below to configure the Bluetooth driver on the host system. Please note that, when searching nearby Bluetooth devices on Host computers, the Xi3000-BT will come out with the serial number as their device name. Please check the serial number label on the scanner when making connections.
  • Page 12 3. Select Client Applications tab and select Bluetooth Serial Port from the list then 7. The serial ports are assigned to the device, outgoing COM 10 and Incoming click Property button. COM 11. Click the Finish button to complete the configuration. 4.
  • Page 13 This will enable the connecting process. If Authentication (Secure Connection) is enabled, another window might pop up and asking for PIN code. 5. Wake up Xi3000-BT by pulling the trigger (just in case it falls asleep). Double click Find Bluetooth Devices.
  • Page 14 After the connection is closed, the Xi3000-BT scanner and the Bluetooth driver The Xi3000-BT scanner can be configured to the standard Bluetooth HID as data are properly configured and are ready to go. User can now run their application output interface.

  • Page 15: Hid K Eyboard I Nterface

    6.1.3 Authentication & PIN Code not available on the scanner is needed. The Xi3000-BT scanner can do connection authentication if communication security is desired. Once this setting is enabled, a user configurable PIN code is verified during connection establishment. The scanner will refuse connection if the PIN code is incorrect.

  • Page 16: C Onfiguring B Luetooth D Evice D River

    Please follow the procedures below to configure the Bluetooth driver on the host system. Please note that, when searching nearby Bluetooth devices on Host computers, the Xi3000-BT scanner will come out with the serial number as their device name. Please check the serial number label on the scanner when making 5.
  • Page 17 3. Right click the Xi3000-BT scanner and select Pair Device. 8. The scanner is ready to use. Please click OK button. 4. Input PIN code and click OK button. 6.3.2 Widcomm Bluetooth Driver 5. Right click Xi3000-BT scanner and select Discover Available Services.

  • Page 18: I Taly / F Rench P Harmacode

    7. Symbology Parameters 6. Click PC Remote Commander icon. This section describes user configurable parameters that are pertaining to barcode symbologies. 7.1 Code39 • Standard / Full ASCII Code 39: User can choose to read either Standard Code 39 or Full ASCII Code 39 by configuring this parameter. •...

  • Page 19: Ean13

    • Checksum Transmission: This parameter specifies whether the checksum • System Number Transmission: If this parameter is enabled, the system character is included in the data being transmitted. number will be included in the data being transmitted. • Code Length Qualification: Because of the weak structure of the 2 of 5 •...

  • Page 20: Plessey

    • Checksum Verification: Three kinds of checksum calculations can be • Code ID Transmission: If this parameter is enabled, the Code ID selected implemented into MSI code: Single Modulo 10, Double Modulo 10, or by the preceding setting will be included in the data being transmitted. Modulo 11 &...

  • Page 21: Data Output Format

    8. Data Output Format Set 1 Set 2 Set 3 Set 4 Set 5 Code 39 Italy Pharmacode Data read by the scanner will be processed in the following sequence (RS-232, French Pharmacode Industrial 25 Keyboard Wedge and USB interfaces). Interleave 25 1) The character substitution is performed on the barcode data.

  • Page 22: Data Editing

    9.3 Applicable Conditions Three applicable conditions can be configured to qualify whether the data read by The Xi3000-BT scanner provides advanced data editing functions for data the scanner can be processed by the particular editing format. Data editing will not formatting.

  • Page 23: Additional Fields

    9.10 Exclusive Data Editing always included in the field. User though, has the option of discarding this terminating string. • Field Length: The field division can be simply specified by the field length. If this parameter is enabled, all data read by the scanner must be processed by the The scanner will assign the next specified number of characters into the editing format.

  • Page 24: Configuring Your Xi3000-Bt

    For most of the parameters, only one read is required to set them to new values. The configuration of Xi3000-BT Scanner is done by reading the setup labels The scanner will respond with two beeps when these parameters are configured.

  • Page 25: Key Type/Status Setting

    • Add Control (L): The left Control key will be sent together with the used. These parameters are: Prefix Code, Postfix Code, Code ID, and Additional Fields of Editing Formats. character programmed. • Add Alternate (L): The left Alternate key will be sent together with the The available key type/status settings can be selected will be described briefly.

Table of Contents