Contents Part 1: Introduction and Specifications....1-1 Touchpad Interface ............2-15 External 1394 (IEEE) Interface ........2-15 Specifications ................1-2 External USB Interface-port A ......... 2-15 Part 2: Chipsets and Mainboard ........2-1 External USB Interface-port B ......... 2-15 Mainboard ................2-2 PCMCIA Cardbus Interface Socket A ......
Part 1: Introduction and Specifications Part 1: Introduction and Specifications The model 8500V notebook computer supports up to an 800MHz Intel Pentium!!! processor. The 8500V features a 15.0” TFT LCD panel and one bay for a removable FDD module, which is interchangeable with a Zip 250MB Drive or secondary IDE HDD. This prod- uct also features one bay for a removable CD-ROM, which is interchangeable with a DVD-ROM or CD-RW Drive.
Service Manual Specifications Structure - Full PC 99 Compliant - ACPI 1.0B Compliant Security - Kensington® Lock Processor - Intel Pentium III 500/533/550/600/650/667/700/733/750/800/850/866/933 MHz ( FC-PGA 370 Package) Memory - Provides 64 bit data bus system memory - Expandable memory up to 512 MB, depend on 32/64/128/256 MB SODIMM Module - Two PC-100 or PC-133 compliant 144-pin SODIMM sockets, support Sync DRAM SODIMM (3.3V) BIOS - One 256KB Flash ROM...
Page 5
Part 1: Introduction and Specifications - Motion Compensation and IDCT for DVD playback Acceleration - High quality TV-out with MacroVision® V7.01 anti-copy technology - 8 or 16MB Video memory - CRT resolution up to 1600x1200 x16M non-interlaced - TV resolution 1024x768 x 32bpp - DuoView display capability under Windows 98 - Supports external Video Input Storage...
Page 6
Service Manual Keyboard - 101/102 Key Win 95 keyboard includes numeric keypad PCMCIA - Two (PCI) PCMCIA 3.3V/5V sockets, type II x2 or type III x1 - Supports Zoomed Video Port / CardBus (PC Card95) Interface - Built in Touchpad (PS/2) - IEEE 1394 port - Dual USB port - One serial port (COM1)
Page 7
Part 1: Introduction and Specifications Communication - Wireless Infrared transfer IrDA 1.1, 1cm~1M operating distance, 4Mbps FIR - 56K MDC Modem with V.90 compliant - 100M/10M LAN - Supports ACPI v1.0B - Supports APM v1.2 Soft Off - Device Power Management - CPU over temperature protection - Supports suspend to disk - Battery low suspend...
Page 8
Service Manual Spec. - Temperature Operating: 5 C~ 35 C; Non-Operating : -20 C ~ 60 - Relative Humidity Operating : 20% ~ 80%; Non-operation: 10% ~ 90% Physical - 358(w) x 280(d) x 50(h) mm Weight - 4.2 kg with Lithium-Ion battery Optional - 3002 Lithium-Ion smart battery pack - 8006A Port Replicator...
Part 2: Chipsets and Mainboard LVD S Intel Interface Socket 370 FC-PGA AGP BUS GTL+ HOST BUS SODIMM0 MM BUS TV OUT 82C694X SODIMM1 VIDEO IN PHY TSB41LV02 PCI BUS 3.3V 4450 Part 2: Chipsets and Mainboard ZV PORT RTL8139C ESS1988 82686A RJ-45...
Service Manual Mainboard The mainboard is designed with Intel 370 Socket processor base and includes the following CHIPSET functions: - 82C694X North bridge chipset solution from VIA - 82C686A South bridge chipset solution from VIA - ATI 3D RAGE Mobility-128 Multimedia Flat Panel Controller - TI 4450 PC CARD Controller - FDC37N869 super I/O Floppy Disk Controller - ES1988 PCI Audio Chip and ES1921 AC97’...
Part 2: Chipsets and Mainboard 82C694X Host Bridge System Controller VIA’s 82C694X Host Bridge system controller is a highly integrated device that combines the processor bus controller, the DRAM controller, and the PCI bus controller into one component. The 82C694X Host Bridge has multiple power management features: - Host Interface - Memory Interface - PCI Interface...
Service Manual VGA Controller – ATI 3D RAGE Mobility-128 The ATI 3D RAGE MOBILITY-128 Multimedia Flat Panel Controller is a DRAM based fully integrated LCD, CRT & TV 64 bits con- troller for AGP systems. It contains the following functions: - Supports displays for 8 MB or 16 MB - 64 bit high performance 2D/3D Graphic Engine - Supports bus master AGP and SGRAM memory...
Part 2: Chipsets and Mainboard - Bus Master Transfer capability - Supports both 5V and 3.3V PC cards - Supports PCMCIA_ATA Specification - Supports Advanced Submicron Low Power CMOS Technology - ACPI 1.0 Compliant - 256 pin Micro-Star BGA package - OHCI Link Function is IEEE 1394-1995 Compliant and compatible with Proposal 1394 ZV Port Custom Interface The ZV (Zoomed Video) Port is a single source, point-to-point unidirectional video bus between a PC Card socket and a VGA control-...
Service Manual + High Speed Mode Microsoft and Hewlett Packard Extended Capabilities Port (ECP) Compatible Serial Port - Two high speed NS16C550 compatible UARTs with Send/Receive 16 Byte FIFOs - Programmable Baud Rate Generator - Modem Control Circuitry - Infrared-IrDA, HPSIR, ASKIR, Fast IR(4Mbps IrDA), Consumer IR Support High Performance PCI Audio Chip - ES1988 - 500-MIPS-equivalent, dual-engine PCI audio accelerator - HRTF 3-D positional audio acceleration...
Part 2: Chipsets and Mainboard - Luminance and chrominance signal processing for PAL BGDHIN, Combination-PAL N, PALM, NTSC M, NTSC-Japan, NTSC 4.43 and SECAM - Two-wire, Inter-Integrated Circuit(I2C) - User programmable sharpness control Keyboard Controller - M38867M8 - Memory size: 1024 bytes (RAM) - Timers: 8 bit prescaler X 4 + 8 bit timer X 3 - Comparator: 4 bit X 8 channels - Bus interface: 2 bytes...
Page 16
Service Manual - Fully compliant with IEEE 802.3u 100Base-T SPEC and IEEE802.3x full duplex flow control - Supports Analog Auto-Power-Down 2 – 8...
Part 2: Chipsets and Mainboard External Monitor Interface External S-video out Inter- External 1394 (IEEE) Inter- External USB Interface-port A face face External USB Interface-port B Touchpad Interface 2 – 15...
Part 3: Installing a processor Part 3: Installing a processor The notebook computer supports an Intel Pentium !!! processor. Note: Remember to wear an antistatic wrist strap when adding or replacing the processor. If you remove the heat sink, which is necessary to add or replace the processor, you will need to have a replacement heat sink pad available.
Service Manual A: Remove the heat sink CPU cover 1) Unscrew and remove the CPU cover. 2) Remove the four screws which hold the heat sink in place. heat sink 3) Lift the heat sink out of the computer. B: Remove the existing processor By this step you should have successfully removed the heat sink and are now looking at the CPU socket with processor.
Page 29
Part 3: Installing a processor Align the CPU tool over the CPU. Place the CPU tool on top of the CPU. Place the screwdriver into the open slot on the CPU case, Remove the screwdriver and the CPU tool and gently lift then hold the CPU tool (jig) in place and move the screw- the CPU out of the socket.
Service Manual C: Install a new processor Now you should be looking at an empty CPU socket. To install a new processor simply follow these steps: The empty CPU socket without a processor module. Gently place the processor into the opened CPU socket and press it into place.
Page 31
Part 3: Installing a processor Place the screwdriver into the close slot on the CPU then Remove the screwdriver and the CPU tool. move the screwdriver in towards the CPU. (this will lock the CPU securely in place). Place the ZIF plug (lock) on the CLOSE side of the CPU The processor is now securely locked into the CPU socket.
Service Manual D: Install the heat sink Note: Before installing the heat sink, make sure you place a new heat sink pad on the heat sink. 1) Peel off the old heat sink pad and stick on a new one. 2) Place the heat sink on top of the Hex studs.
2) Choose Download from the menu bar at the top of the page. 3) In the Download Drivers section select the model of your computer (8500V series) and the BIOS driver. 4) Select GO to download the zip file to your computer.
Part 4: BIOS Through DOS 1) Insert a Floppy Disk into your FDD. (This disk will be overwritten and all information erased, so make sure it has no important data on it!) 2) At the DOS prompt type: Format A:/s C: Copy your BIOS files on to the bootable Floppy Disk.
Service Manual Phoenix BIOS Post Error Messages Errors which occur during the POST procedure can be grouped into two categories, fatal and nonfatal. All fatal errors will not allow the system to continue the boot process. Fatal Errors 4 - 4...
Part 4: BIOS Nonfatal errors Most nonfatal errors will allow the sys- tem to boot. Should the system halt due to a nonfatal error, a physical change i t i must be made to the system. i t i i t i ’...
Service Manual ITEM PART NAME PART REMARK KEYBOARD FOR 8500 80-85038-7G SPEAKER COVER (R)+NET 33-8500T-A10 33-8500T-A21 SPEAKER COVER (L)+NET 23-5A020-900 SPEAKER + CON. COVER KNOB POM 42-62082-010 SPRING FOR COVER KNOB 38-62020-020 CARD BUS COVER 42-8507P-010 TOP CASE+G/P+LENS+POWER KNOB 39-85V01-010 47-35097-020 EMI SPONGE(2) FOR K/B EMI SPONGE(A) REAR BRL TOP B/C...
Page 50
Service Manual V TT V TT V TT H D # [0 ..6 3 ] HD#[0..63] HA #[3..31] RN68 HA #[3..31] H A# 1 6 RN105 RN89 H A# 3 H D # 4 5 H D # 1 8 H A# 5 H D # 3 9 H D # 9...
Page 51
Part 6: Schematics -B S E L1 VT T For J os hu a VC C _ C O R E C123 C124 C126 U45B VID0 AL35 A 37 4.7U(1206) 4.7U(1206) 4.7U(1206) 4.7U(1206) 4.7U(1206) 4.7U(1206) 4.7U(1206) 4.7U(1206) VID0 VID0 VID1 A M36 A B 32 VID1...
Page 52
Service Manual HD#[0..63] HD#[0..63] Near t o VT82C694X VT T AD[0..31] 5,7,16,18,21 75 1% HD#0 HD#1 GT LVREFB HD#2 HD#3 HD#4 0.1U 150(1%) HD#5 HD#6 HD#7 HD#8 HD#9 HD#10 AD10 VT T AD10 HD#11 AD11 AD11 HD#12 AD12 AD12 HD#13 AD13 AD13 75 1%...
Page 56
Service Manual R659 10K (R) V CC3 R660 R661 V CC3 V DD3 A 20M#- R213 4.7K P DD0 P 16 B ITCLK S US ST# R471 R118 PDD[0..15] P DD0 SDD0/B ITCLK B ITCLK P DD1 P 18 V 17 S DIN IGNNE #- R119...
Page 60
Service Manual VCC3 VCC3 RAT IO 0 R535 R539 R559 R568 RAT IO 1 RAT IO 2 RAT IO 3 RN55 A20M# A20M#- U34A IG NNE#- 7407 8P4R-10K INT R- RN56 NMI- 8P4R-1K VCC3 VCC3 RAT IO 0 IG NNE# O E0 RAT IO 1 O E1...
Page 61
Part 6: Schematics V CC Z372 0(1206) Q1 P IN C 1 -> FA N _V O V CC C 412 1S S 355 40MIL CN29 V CC3 1U(0805) Z630 6.8K FA N _V O FA N_S E N 2S C 4672 34.8K (1% ) R 358 40MIL...
Page 62
Service Manual CN14 COL8 COL7 C691 0.1U COL6 0(1206) COL5 K B VCC C349 0.1U COL4 COL3 COL2 CN18 COL1 EM C L K ROW1 FCM2012V -301 E MCLK ROW2 EM D A FCM2012V -301 1S S355 E MDA R O W 4 EKD A FCM2012V -301 E KDA...
Page 63
Part 6: Schematics VCC3 C201 IRQ7 C203 C225 C233 8,9,12,13 SA[0..15] FDC37N869(TQFP ) IRQ3 0.1U 0.1U 4.7U(1206) C532 S A 0 V CC IRQ4 S A 1 V CC S A 2 C200 S A 3 RN59 RN122 IRQ5 S A 4 DRV0# 8P 4R-4.7K 8P 4R-4.7K...
Page 64
Service Manual R381 0(0805)(R) K BV 3 CN20 R380 0(0805) V CC V CC C102 0.1U(K% ) DTRA C444 CTS A 0.1U(K% ) 0.1U SO U T A RTS A C100 S INA D SR A 0.1U(K% ) 0.1U(K% ) DCDA S OUT 1 COMP3...
Page 65
Part 6: Schematics LA NVDD3 LA NVDD3 C134 C136 C137 CLKOUT 0.1U 0.1U 0.1U(R) 0(0805) C135 R412 R112 C461 X TALF 25MHz CRY S TA L Anal og Digi tal GND C462 C463 TXD- TXD- TX D+ TX D+ R113 RX IN- RX IN- 1.7K...
Page 70
Service Manual V CC A VDD MIC IN / INTMIC 0(0803) INTMIC SPDIF OUT S PDIF R208 C219 0.1U S PDIFON S PDIFOUT FCM2012V -301 S PDIF MIC_IN MIC1 R202 C537 C188 C179 P HONE JA CK V CC 0.22U DVD_DRV P I5A 319A(S O8) C208...
Page 71
Part 6: Schematics C N 2 C N 3 L 5 7 0 (0 8 0 5) MS P K L MS P K R MS P K L MS P K R M S P K L G M S P K R G M S P K L G M S P K R G A MP V D D...
Page 72
Service Manual S TP _A GP # GA D[31..0] GA D[31..0] A GP _B US Y # 24 R B F# GB E#[3..0] GB E#[3..0] A D_S TB 0 A D_S TB 1 INTR D # 7,18 INTR D # S B _S TB 4,24 GFR A ME #...
Page 73
Part 6: Schematics SGRAM ME M_MD[63..0] S GMD[63..0] ME M_MD[63..0] S GMD[63..0] S GMD[63..0] MEMORY DATA S GMD[63..0] MEMORY ADDRESS S GMA [11..0] S GMA [11..0] MA X SGMD31 MA X SGMD63 A 9/A 10 DQ31 A 9/A 10 DQ31 MA Y SGMD30 MA Y...
Page 74
Service Manual V CC V CC V CC 23,26 CRMA FCM2012V -301 C386 C401 CN23 75(1% ) TVA GND DA221(R) DA221(R) DA221(R) CRMA S LD COMP S LD FCM2012V -301 DDCDA R326 100 FCM2012V -121 C387 S LD DDCDA C402 CN21 DDCLK FCM2012V -121...
Page 75
Part 6: Schematics HO LEC315D126N-V8 HO LEC315D126N-V8 HO LEC315D126N-V8 HO LEC315D126N-V8 HO LEC315D110N-V8 HO LEC315D110N-V8 HO LEC315D110N-V8 CN27 HO LEC315D110N-V8 HO LEC315D110N-V8 HO LEC315D110N-V8 HO LEC315D110N-V8 HO LEC236D110N-V8 USBP1+ USBP1+ DT RA DT RA USBP1- CT SA CT SA USBP1- SOU T A HO LEC315D110N-V8 SOUT A...
Page 76
Service Manual V CC3 U826 B AT N.C. B A K CTL# B A K CTL# TC7S O4F E NA VE E E NA B K KL E NA VE E E NA B K KL R743 V CC3 B E E P_E N# CN33 B E E P_E N# C601...
Page 77
Part 6: Schematics VCC3 SPARE VTT+ R198 14m(1206) C213 Z748 47UF/6.3V(D) SENSEN- SI3443(TSOP-6) Z745 PDR V C215 GN D 104(0805 K) 4.7U H(SDS1005-4R 7M) Z746 Z742 R UN /SS SYN C R523 LTC1622 (MSOP8) R468 R524 2N3906 10K(0603 J) R469 C508 10K(0603 J) 103(0603 K)
Page 79
Part 6: Schematics CN 2 8 +12V CN 3 2 B ATFU L L BA TC HA 7 ,25 ,2 7 B ATFU L L BA TC HA 25 ,2 7 S H U T D O WN B ATLO W # 7 ,1 2 S HU TD O WN B ATLO W #...
Page 80
CON10 SML_020_MLT _BAT _BEEP _HD_LED HOLE276D94 LED1 SML_010_MLT _SUS_LED LED1 SML_010_MLT HOLE276D94 HOLE276D94 KAPOK COMPUT ER CO. CLEVO T i t l e LED_BOARD Size Document Number Custom LED_BOARD Date: Fri d ay, October 20, 2000 Sheet 6 – 32...
Page 85
Part 6: Schematics HOLEC31 5D110N-V8 CN39 CN37 0(0803 ) L100 0(0803 ) MODEM-EX T -RJ11 FAN_CON C697 C698 KAPOK ³Í³Õ¹q¸£ Si z e Document Numbe r Custom 2.0A RJ-11 Date: Fri d ay, Octob er 20, 2000 Shee t 6 – 37...
Page 86
Service Manual GND OF C13 IS NEAR TO Q5 GND OF C10 IS NEAR TO Q8 2UH (5 5050 ) 10UF/25V(2220 ) FU SE 22 U F/25 V(D IP10X 5 ) 22 U F/25 V(D IP10X 5 ) 2.2UF/25V(1206 ) SI4410 (SO-8 ) 2.2UF/25V(1206 ) 2.2UF/25V(1206 )
Page 87
Part 6: Schematics CC O KS823 C04(T O-252) R7 7 D2 3 0(1 206) AIC431 SK 2 4 LT112 1CS8-5(SO8) SI4 435(SO-8) R7 8 0(1 206) SH DN (ADJ) 1 0K SK 2 4 C3 8 47 0 2.2UF/2 5V(1 206) C2 4 SS5GN D 2.2UF/2 5V(1 206)
Page 88
Service Manual CN 1 D D _ON D D _ON J P1 VC C S VC C S C C O H EAD ER 2 F B0 C C O VC C S VCC 3 VCC 3 VC C VC C R 88 J P2 R 15...