Related Manuals for Simplicity Central Vacuum Power Units
Summary of Contents for Simplicity Central Vacuum Power Units
- Page 1 Central Vacuum Power Units (The chances are you’re never going to read me) Owner’s Manual All Models...
-
Page 2: Table Of Contents
Contents IMPORTANT SAFETY INSTRUCTIONS Grounding Instructions Installation Schematic Unit Installation Do’s and Don’ts Operating Instructions Muffler Installation Hose Hook-up & Inlets Using the Front Utility Valve Maintenance Maintenance Suggestions Motor Changing the HiFlow HEPA Bag Dirt Receptacle Filters Problem Solving Guide Circuit Breaker Trips Troubleshooting Warranty... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY Installation INSTRUCTIONS GROUNDING INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including This appliance must be grounded. If it should malfunction or breakdown, grounding the following: provides a path of least resistance for electric current to reduce the risk of electric READ ALL INSTRUCTIONS BEFORE shock. - Page 4 Installation Installation Filtered Cyclonic Units (C2, CI4, CI6 and CI10 models) HEPA Bagged Units (B2, BF4, BF6 and BF10 models) 1. Circuit breaker 1. Circuit breaker 2. Low voltage connector 2. LEDS* 3. Serial number 3. Low voltage connector 4. Integrated inlet* 4.
-
Page 5: Unit Installation
Simplicity Retailers. Contrary to all other connections in the piping system, do not glue the last fitting to your unit. Simplicity central vacuums are equipped with an adjustable air intake valve (figure 3), which does not require glue. An air-tight fit is achieved with the screw-type adjustment on the fitting itself. -
Page 6: Do's And Don'ts
Installation Installation Do’s and Don’ts cont. Do’s and Don’ts cont. Installing Conduits Installing Inlets When installing your vacuum inlets, we recommend that the principle of electric polarity be taken into account. Ensure that the wire connected onto contact A on inlet 1 is the same as that connected to contact A on inlet 2, and so on. -
Page 7: Operating Instructions
Operating Instructions Operating Instructions Muffler Installation (optional) Hose Hook-up and Inlets 1. Insert the rubber coupling (A) on the air exhaust (D). Before operating your central vacuum… 2. Using a Phillips (star shape) screwdriver, tighten the clamp collar on the rubber Please verify that it is properly connected to the piping system, and to a grounded coupling to ensure adequate sealing. -
Page 8: Using The Front Utility Valve
Operating Instructions Maintenance Using the Front Utility valve Maintenance Suggestions (CI4, CI6 and CI10 models) Your unit is equipped with an electronic To use the vacuum inlet integrated into your central vacuum, simply connect timing board that will suggest, by the color the hose and flip the integrated switch to the “on”... -
Page 9: Motor
Maintenance Motor Changing the HiFlow HEPA Bag Please note that Simplicity motors do not require lubrication. Each motor contains (B2, BF4, BF6 and BF10 Models) two carbon brushes which will wear normally, and may eventually require Change the bag when the one in place is replacement. -
Page 10: Dirt Receptacle
Maintenance Maintenance Dirt Receptacle (C2, CI4, CI6 and CI10 models) Carbon Dust Filter Occasional maintenance of the dirt receptacle is necessary to ensure constant, (B2, BF4, BF6 and BF10 Models) lasting performance. We recommend that it be emptied at least every season, We recommend changing this filter after three depending on frequency of use. -
Page 11: Problem Solving Guide
Problem Solving Guide Problem Solving Guide Circuit Breaker Trips Trouble Shooting Guide Your Simplicity central vacuum includes a circuit breaker that will shut off your power Problem Possible Reasons Possible Solution unit in the event of a problem with the motor. One common reason why a breaker will Vacuum system •... -
Page 12: Warranty
(3) years from the date of original consumer purchase. In the event of a defect in permanently installed components of a Simplicity central system, an authorized Simplicity retailer should be contacted. The retailer will repair or replace (at our option) any defective part or parts at your location at no labor cost for a period of three (3) years. - Page 13 www.simplicityvac.com ©2008 Tacony Corporation IB-SPU...