Cub Cadet GT 2554 Operator's Manual
  1. Manuals
  2. Brands
  3. Cub Cadet Manuals
  4. Tractor
  5. GT 2554
  6. Operator's manual
Cub Cadet GT 2554 Operator's Manual

Cub Cadet GT 2554 Operator's Manual

2500 series
Hide thumbs Also See for GT 2554:
Table of Contents

Advertisement

Quick Links

O
M
PERATOR'S
ANUAL
SERIES 2500
TRACTOR
Model Number
GT 2554
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
CUB CADET LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 [www.cubcadet.com]
PRINTED IN U.S.A.
FORM NO. 769-01033A
(9/04)

Advertisement

Table of Contents
loading

Related Manuals for Cub Cadet GT 2554

Summary of Contents for Cub Cadet GT 2554

  • Page 1 Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. CUB CADET LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 [www.cubcadet.com] PRINTED IN U.S.A.

  • Page 2: Emission Control Systems Warranty

    KOHLER CO. FEDERAL AND CALIFORNIA EMISSION CONTROL SYSTEMS LIMITED WARRANTY SMALL OFF-ROAD EQUIPMENT ENGINES The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Kohler Co. are pleased to explain the Federal and California Emission Control Systems Warranty on your small off-road equipment engine (herein engine). For California, engines produced in 1995 and later must be designed, built and equipped to meet the state’s stringent anti-smog standards.

  • Page 3: Table Of Contents

    CONTENTS Section Page Section Page Emission Control Systems Warranty ... Off-Season Storage ......Tractor Preparation ......Mowing..........Safe Operation Practices ..... Optional Equipment and Accessories . Product Graphics ......... Maintenance Chart....... To The Owner ........Trouble Shooting........Calling Service Information ....Lubrication Table .......

  • Page 4: Safe Operation Practices

    WARNING • The engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. • This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered, or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
  • Page 5 When going downhill, the extra weight may exhaust presenting a potential fire hazard. cause you to loose control and possibly overturn the tractor. 22. Use only accessories approved for this machine by Cub Cadet. Read, understand and follow all III. CHILDREN instructions provided with approved accessory.
  • Page 6 6. To avoid back-over accidents, always disengage 8. After striking a foreign object, stop the engine, the cutting blades before shifting in reverse. The remove the wire from the spark plug and "Reverse Caution Mode" should not be used thoroughly inspect the mower for any damage. when children or others are around.

  • Page 7: Product Graphics

    PRODUCT GRAPHICS ing, painted over or can no longer be read. Replace- ment safety graphics are available through your Keep product safety graphics (decals) clean. Replace dealer. any safety graphic that is damaged, destroyed, miss- STARTING INSTRUCTIONS BE FAMILIAR WITH CONTROLS BEFORE D A N G E R STARTING ENGINE AND OPERATING.

  • Page 8: To The Owner

    LEVEL SURFACE before pulling the transmission release lever to the disengaged position. Your local authorized Cub Cadet dealer is interested in the performance you receive from your tractor, and with the maintenance needed to ensure the satisfactory operation of your tractor. The dealer has trained service personnel familiar with the latest servicing information, is equipped with the latest tools, and has a complete line of genuine Cub Cadet service parts which assure proper fit and high quality.

  • Page 9: Controls And Indicators

    SECTION I. CONTROLS AND INDICATORS Your Cub Cadet Tractor has been safety engineered. Thoroughly acquaint yourself with all the controls and This section gives a brief description of the function indicators before attempting to start or operate the and location of the various controls and indicators.
  • Page 10 KEY SWITCH MODULE tery voltage is also displayed on the hour meter. If this indicator and display come on during oper- ation, check the battery and charging system for INDICATOR possible causes and/or contact your Cub Cadet REVERSE LIGHT PUSH dealer.
  • Page 11 • START — Energizes the starter motor to crank The brake lock lever, located in the center of the and start the tractor engine. Release the key as dash panel below the steering wheel, is identified soon as the engine starts and the key will return with the symbol.
  • Page 12 If the interlock sys- stalled. tem should ever malfunction, do not operate the trac- tor. Contact your authorized Cub Cadet Dealer. The safety interlock system prevents the engine from N. SEAT ADJUSTMENT LEVER cranking or starting unless the brake pedal is fully de- The seat adjustment lever (See Figure 6) is used to pressed, and the PTO switch is in the “OFF”...
  • Page 13 HOOD AND SIDE PANELS 3. Grasp the side panel just behind the grille and pull outward to release the side panel from the The tractor hood is arranged to swing up and forward tapered bushings on the grille. for easy access to the engine compartment (See Fig- ure 8).

  • Page 14: Operation

    SECTION II. OPERATION Methyl Tertiary Butyl Ether (MTBE) and unleaded gasoline blends (up to a maximum of 15% MTBE WARNING by volume) are approved fuels. Other gasoline/ ether blends are not approved. RECEIVE INSTRUCTION Read 4. Check the engine and transmission oil levels. operator’s manual.
  • Page 15 STARTING THE ENGINE 5. Turn the ingnition key to the “START” position and hold until the engine starts; however, do not crank the engine continuously for more than 10 WARNING seconds at a time. Once the engine starts, gradually adjust the choke as needed to keep the engine For personal safety, the operator must be sitting running until warmed up, then push the choke control in the tractor seat when starting the engine.
  • Page 16 b. Lightly push the cruise control lever downward DRIVING THE TRACTOR as far as possible and hold in this position. c. While continuing to hold the cruise lever down, CAUTION lift your foot from the forward control pedal (you should feel the cruise latch engage). Avoid sudden starts, excessive speed and d.
  • Page 17 Back the tractor with implement up the steepest portion OPERATING THE POWER TAKE-OFF (PTO) CLUTCH of each slope you intend to work. If the tractor cannot IMPORTANT: NEVER engage the PTO clutch while its negotiate the slope in reverse, the slope is too steep to driven equipment is under load (e.g., mower deck low- be worked.
  • Page 18 USING THE “REVERSE CAUTION MODE” KEY 2. Turn the key from the “NORMAL MOWING” POSITION (Green) position to the “REVERSE CAUTION MODE” (Yellow) position of the key switch The “REVERSE CAUTION MODE” position of the key module. Refer to Figure 10. switch module allows the machine to be operated in re- verse with the blades (PTO) engaged.

  • Page 19: Adjustments

    SECTION III. ADJUSTMENTS This section contains adjustment information for the To adjust the braking force proceed as follows (Refer Model GT 2554 tractor. Adjustment information for the to Figure 12): 54 inch deck is located in Section V – Mower Deck 1.
  • Page 20 WHEEL ALIGNMENT 5. Disconnect the front ball joints from the steering arms by removing the hex lock nuts (Refer to The front wheels should toe-in approximately 1/8 to Figure 14). Manually move each wheel to achieve 1/4 inch, as measured across dimensions A and B the required toe-in and equal D measurements.
  • Page 21 2. Pivot the ends of the axle up and down to check for binding. If the axle is binding, loosen the lock nuts WARNING (See Figure 15) until binding is eliminated. Place the tractor on a firm and level surface and chock the front wheels before raising the rear PIVOT AXLE wheels from the ground.
  • Page 22 CONTROL 1. Front Control Rod 2. Rear Control Rod 3. Hex Tap Screw 4. Hex Wash Hd Tapp Screw 5. Control Arm 6. Control Arm Pin 7. Neutral Arm 8. Centering Pin 9. Neutral Return Adjust. Brkt. 10. Internal Cotter Pin Figure 16 Adjusting the Control Rod ADJUSTING LIFT ASSIST SPRING TENSION...
  • Page 23 CARBURETOR ADJUSTMENTS NOTE WARNING Carburetor adjustments should be made only When making adjustments to the carburetor after the engine has warmed up. while the engine is running, disengage the PTO 1. Start the engine and run at half throttle for 5 to 10 clutch and engage the brake pedal lock.

  • Page 24: Maintenance

    OIL LEVEL are recommended. DIPSTICK Ambient Temperature Viscosity (Grade SG/SH) OPERATING +32°F and Above — Cub Cadet Engine Oil S.A.E. RANGE 10W30 Below +32°F — Cub Cadet Engine Oil S.A.E. 5W20 or S.A.E. 5W30* OIL FILLER *Synthetic Engine Oil S.A.E. 5W20 or S.A.E. 5W30 is acceptable, up to 40°F.
  • Page 25 For best results, fill to the “FULL” mark on the change interval. The filters can be obtained dipstick as opposed to adding a given quantity through your Cub Cadet dealer under part of oil. Always check the level on the dipstick number KH-12-050-08.
  • Page 26 While the engine oil is warm, proceed as follows: FILLING THE CRANKCASE NOTE CAUTION A 12 inch length of flexible tubing is supplied in the owner’s manual package and should be Never overfill the engine crankcase. The engine used to drain the engine oil. may overheat and/or damage may result if the crankcase is below the “LOW”...
  • Page 27 The filter can be obtained through your Cub Cadet dealer under the part number 923-3014. Refer to the LUBRICATION TABLE for information regarding the oil capacity and the proper type of oil to pour into the transmission case.
  • Page 28 2. Remove the foam precleaner by sliding it up off the paper element (Refer to Figure 23). CAUTION 3. Wash the precleaner in warm water with detergent. Rinse the precleaner thoroughly until all If the transmission oil is to be re-used, cover the traces of the detergent are eliminated.
  • Page 29 3. Remove the wing nut and element cover plate, SPARK PLUG then lift out the paper air filter element. 4. Do not wash the paper element or use pressurized WARNING air, as this will damage the element. Replace a dirty, bent or damaged element. Handle new To avoid possible injury, be sure the engine is elements carefully;...
  • Page 30 Replace headlight bulbs as follows: (See Figure 25) GENERAL BATTERY INFORMATION 1. Unplug the wire harness leads from the headlight socket terminals. Note which wire connects to WARNING each terminal before disconnecting. a. Battery posts, terminals related 2. Rotate the socket assembly as follows to remove accessories contain lead...
  • Page 31 STORAGE OF THE BATTERY 1. When storing the tractor for extended periods, disconnect the negative battery cable. It is not WING NUT necessary to remove the battery. 2. All batteries discharge during storage. Keep the ROTATE HOLDDOWN exterior of the battery clean, especially the top. A UPWARD STRAP TAB dirty battery will discharge more rapidly.
  • Page 32 CHARGING THE BATTERY Tire SizePounds per Square Inch Test and, if necessary, recharge the battery after the Front Tires tractor has been stored for a period of time. 16 x 6.5–8 • A voltmeter or load tester should read 12.6 volts (DC) or higher across the battery terminals.

  • Page 33: Mower Deck

    SECTION V. MOWER DECK A. INSTALLATION AND REMOVAL OF DECK INSTALLATION OF DECK WARNING Before installing the mower deck, place the PTO switch in the “OFF” position, engage the brake pedal lock, turn the ignition key to the “OFF” position and remove the key from the switch.
  • Page 34 8. While holding the front lift rod up, slide the mower deck forward until the rod aligns with both front NOTE roller bracket slots. Lower the lift rod into the front roller bracket slots and slide the deck rearward to If installing the deck on a new tractor, cut the engage the lift rod fully forward in the slots of the cable tie used to hold the front lift rod up during...

  • Page 35: Warning

    NOTE: It may be necessary to lift each side of the deck 13. Pass the PTO belt upward inside the front of the and maneuver it slightly to align the support pins with tractor frame and install the forward end of the belt the holes of the lift links.

  • Page 36: Warning

    CASTOR CHANNELS PTO BELT FRONT CASTOR ASSEMBLIES MOWER DECK CENTER DOUBLE REAR PULLEY BALL WHEELS FRONT OF DECK Figure 38 17. While holding the belt in position, rotate the deck QUICK PINS idler arm lever into its stop bracket to tension the PTO belt (Refer to Figure 39).

  • Page 37: Warning

    4. Remove the rearward end of the PTO belt from the upper pulley of the deck center double-pulley (Refer to Figure 42). Engage the deck idler arm lever back into its stop bracket (See Figure 43). CLUTCH CLUTCH PTO BELT PULLEY PULLEY MOWER DECK...
  • Page 38 TRACTOR LATCH RECEIVER (BOTH SIDES) QUICK LIFT ATTACH LINK SHOULDER BOLT (BOTH SIDES) DECK SUPPORT REAR DECK FRONT LIFT PIN DISENGAGED BRACKET ROD/BRACKET (BOTH SIDES) ASSEMBLY Figure 48 Figure 46 8. Raise the tractor implement lift handle to its highest setting. Roll the mower deck forward until CAUTION the front lift rod slides up and out of the openings of both front roller bracket slots.

  • Page 39: Warning

    B. DECK LEVELING ADJUSTMENTS The 54" mower deck is equipped with ground following front castor wheels and is designed to run on its own wheels. However, to ensure even cutting, the mower DECK deck should be properly leveled. The leveling INSTALLED procedure will result in the left and right blades having corresponding cutting-edge-to ground measurements...

  • Page 40: Front To Back Leveling Adjustment

    8. Loosen the upper jam nut on the lift link rod and 3. Position the mower blades so the ends of each turn away from the adjustment ferrule. Turn the blade point to the front and the rear of the tractor lower lock nut upward (tighten) on the threads of (See Figure 54).

  • Page 41: Warning

    8. Raise the deck to the highest position. Recheck To adjust the mower deck cutting height by raising or the blade measurements described in step 4. If the lowering the ball wheels, refer to Figure 56 and resultant measurements are not correct, repeat proceed as follows: steps 5, 6 and 7 until the proper measurements are 1.

  • Page 42: Warning

    C. MAINTENANCE HEX NUT BLADE CARE WARNING Before performing any maintenance, place the PTO switch in the “OFF” position, engage the brake pedal lock, turn the ignition key to the “OFF” position and remove the key from the switch to avoid accidental starting and injury. When servicing the mower deck, be careful not WOOD BLOCK 1-1/8"...

  • Page 43: Spindle Drive Belt Replacement

    • Turn off the water supply. SPINDLE DRIVE BELT REPLACEMENT • Pull back the lock collar of the nozzle adapter to In order to replace the spindle drive belt, refer to Figure disconnect the adapter from the nozzle. 60 and Figure 61 and proceed as follows: •...

  • Page 44: Off-Season Storage

    SECTION VI. OFF-SEASON STORAGE If the machine is to be inoperative for a period longer 2. If emptying the fuel system: than days, following procedures recommended: WARNING Do not drain fuel when the engine is hot. Allow WARNING the engine adequate time to cool. Drain fuel into an approved container outdoors, away from Never store the tractor with fuel in the tank open flame.

  • Page 45: Mowing

    SECTION VII. MOWING MOWING WARNING To avoid possible injury, do not allow anyone in the area opposite the discharge chute while mowing. Although area been supposedly cleared of foreign objects, small objects may be picked up and discharged by the mower. Never direct the discharge of material toward bystanders or allow anyone near the machine while in operation.

  • Page 46: Optional Equipment And Accessories

    Refer to the allied equipment can be purchased from, and installed attachment guide for a complete description of by, your authorized Cub Cadet dealer. equipment and required components that can be utilized with your tractor.

  • Page 47: Maintenance Chart

    MAINTENANCE CHART 10 hours 30 hours or 50 hours 100 hours Operation to Before or once three times or twice Before be performed each use a month a season a season yearly storage Clean grille, engine More often air inlet screen, dash under dirty intake screen and side conditions...

  • Page 48: Trouble Shooting

    TROUBLE SHOOTING Possible Cause Possible Remedy HARD TO START No gasoline in fuel tank or carburetor ..... Fill the tank with gasoline. Check the fuel line, carburetor and fuel filter. Fuel line or carburetor clogged........ Clean the fuel line and carburetor with a commercial carburetor cleaner.
  • Page 49 TROUBLE SHOOTING Possible Cause Possible Remedy LACK OF POWER Air cleaner clogged ..........Service the air cleaner element. Refer to “MAINTE- NANCE.” Engine overload ............Reduce the load. Engine overheated..........Make sure the air intake screen, shrouding, engine fins, side panels, dash intake screen and grille are free of accumulated dirt and debris.

  • Page 50: Lubrication Table

    Cub Cadet Drive System Fluid Plus and transaxle with before needed 6 qts NOTE: Cub Cadet Drive System Fluid Plus is specially filter each formulated for this application. If any other oil is used Cub Cadet will not be responsible for substandard performance.

  • Page 51: Lubrication Guides

    LUBRICATION GUIDE WARNING The service life and reliability of any machine depends upon the care it is given. Proper lubrication is a very important part of that care. This lubrication schedule reflects the minimal requirements to maintain the equipment. More frequent inspections and maintenance is preferable. NOTE: We do not recommend the use of a pressure Lubricant is cheap.
  • Page 52 LUBRICATION GUIDE...

  • Page 53: Lubrication Guide

    LUBRICATION GUIDE —Before Each Use 1. Engine filler cap and Check the oil (with the engine stopped) and add sufficient new oil to bring it to dipstick the “FULL” mark on the dipstick. Do not overfill. Do not operate the engine if the oil level is below the “LOW”...

  • Page 54: Specifications

    Engine Speed (governed) Low Speed ..............1200 RPM High Speed (no load) ........... 3600 RPM ± 75 Ignition ................Battery Spark Plug Gap (Cub Cadet No. 759-3336) .....030 in. ELECTRICAL SYSTEM System Voltage ............... 12 volt neg. ground Battery ................725-1707D Alternator .................

  • Page 55: Slope Gauge

    SLOPE GAUGE (Keep this sheet in a safe place for future reference.)

  • Page 57: Warranty - Commercial Use

    CUB CADET CORPORATION MANUFACTURER’S ONE YEAR LIMITED WARRANTY (COMMERCIAL USE) The limited warranty set forth below is given by CUB CADET CUB CADET does not extend any warranty for LLC (“CUB CADET”) with respect to new merchandise products sold or exported outside of the United...

  • Page 58: Warranty - Residential Use

    CUB CADET will, at its option, repair or re- warranted product. place, free of charge, any PTO clutch or mounting hardware found to be defective in material or workmanship provided this product has been operated and maintained as set forth above.

  • Page 60: Maintenance Parts Chart

    MAINTENANCE PARTS CHART MODEL GT 2554 SERIES 2500 23 HP KOHLER Engine Oil Requirements approx. . . 4 pints Part No. ENGINE OIL Cub Cadet engine oil Ambient temperature viscosity (Grade SG,SH,SJ or higher) Above +32°F SAE 10W30 737-3030A (10W30) Below +32°F...

Table of Contents