SERVICING YOUR TRIMMER Loss of Power or Engine Speed Won’t PRODUCT REGISTRATION ....Maintenance Safety......Increase..........*00X31VL3 D210* QUESTIONS? 00X31VL3 D210 Contact your Honda dealer. There is a dealer locator at www.powerequipment.honda.com © 2013 American Honda Motor Co., Inc. All Rights Reserved...
We want to help you get the best results from your new trimmer and to operate it safely. This manual The Honda HHT25S and HHT35S trimmer/brush cutters are designed contains information on how to do that; please read it carefully.
PARTS AND CONTROLS These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact an authorized Honda servicing dealer for a replacement. Loop Type Handle CUTTING-LINE HEAD...
Carefully remove the trimmer and loose parts from the carton and compare the loose parts against the following list. Contact the THROTTLE TRIGGER authorized Honda dealer from whom you purchased the trimmer if any of the loose parts shown are not included with your trimmer. 5 x 28 mm...
4. Tighten the four 5 x 28 mm bolt/washers. All output shafts use left-hand threads. TORQUE: 3.6 ft-lb (5 N·m) 5. Make sure the tie straps are positioned as shown. TIGHTEN CUTTING-LINE HEAD WASHER (used with Kwik COLLAR Loader head only) (left-hand thread) SPACER B...
Please Register Your Trimmer 1. Turn the blade POST cover slowly Please take a few minutes and register your purchase with Honda. until the cover You can register by completing and mailing the registration card on latch is clear of...
Shoulder Harness manual. Know what the controls do and how to operate them. A full shoulder harness must be worn by the operator of these Honda Familiarize yourself with the trimmer and its operation before you trimmers/brush cutters when equipped with a blade and debris shield.
Check Your Shoulder Harness and Check the Engine Oil Level Trimmer Adjustment Check the engine oil level before each use, or every 10 hours if operated continuously. Rest the trimmer on a level surface with the Adjusting the Harness engine stopped. Adjust the harness so the quick-release latch is at your right hip, as 1.
MAINTENANCE” on page 28 for information regarding fuel Honda trimmers are designed to give safe and dependable service if deterioration. operated according to instructions and intended use. 1. To refuel, set the trimmer on level ground and remove the fuel Honda trimmers are intended to be used by an experienced, trained tank cap.
Blades on Honda HHT25S and HHT35S trimmers rotate counterclockwise, as viewed from the operator’s position. Therefore, the left side of the blade is moving toward you. With these trimmers, sawing with the left side of a brush blade will give you better control and less risk of kickback, though it will throw the sawdust toward you.
Attachments DEBRIS surface. Work from an angle where Your Honda trimmer servicing dealer has cutting attachments, debris debris that strikes the shields, barrier kits, and shoulder harnesses that have been designed hard surface will and approved for your trimmer and are covered by warranty. See...
The throttle trigger controls engine speed. The location and operation of the controls are similar on both the HHT25S and HHT35S models. Pulling the throttle trigger toward the control handle grip increases engine speed. The trimmer will have the greatest cutting force at Choke Lever maximum engine speed.
If there is rotation at idle, adjust the idle speed correctly necessary to press the priming bulb. before using the trimmer. For idle adjustment, consult your authorized Honda servicing dealer. 3. Set the throttle trigger in the starting position, using the throttle set button.
Refer to the chart on page 19 for appropriate blade applications. attachment should coast to a stop. If using a blade on a Honda trimmer equipped with a loop handle, also install the optional Honda barrier kit (page 29) that includes a full shoulder harness, a barrier bar, and debris shields for blades.
Every year or Items for 50 hours plus the following: To ensure the best quality and reliability, use only new, Honda 100 hours Genuine parts or their equivalents for repair and replacement.
1. Place a suitable container below the engine to catch the used oil. We recommend the use of a Honda Genuine air filter to ensure it 2. Remove the oil filler cap/dipstick.
MAINTENANCE SCHEDULE Recommended Spark Plug: NGK - CMR5H (page 15). Honda Air Filter Oil can be used instead of NOTICE clean engine oil and is available from your An incorrect spark plug can cause engine damage.
4. Install the spark arrester, top cover, and 5 x 12 mm hex bolt and your trimmer to an tighten securely. authorized Honda servicing dealer to perform idle speed adjustment. 1. Start the engine outdoors, and allow it to warm up to normal operating temperature.
CUTTING ATTACHMENTS Check the fuel supply and return tubes, and replace any tube that is damaged, cracked, or leaking. Refer to the Honda shop manual for tube replacement instructions, or APPLICATIONS take the trimmer to an authorized Honda servicing dealer.
A dull blade can be sharpened, but a blade that is worn out, bent, cracked, chipped, or otherwise damaged must be replaced. If installing a metal blade on a Honda trimmer equipped with a loop When a blade needs sharping or replacement, take the trimmer to a handle, also install the optional Barrier Kit that includes a full Honda trimmer servicing dealer.
SHIELD without a shield installed is not covered under warranty. A variety of blades are available from your Honda trimmer servicing dealer. Always use the debris shield designed for use with a blade when attaching a blade to your trimmer. The blade type debris shield does not have a cutoff knife.
Kwik Loader Cutting-Line Head Always shut the engine off before adding trimmer line to the head. All Honda trimmers come with either a Kwik Loader or semi-matic To load, push the 8-inch trimmer line into the housing so there is cutting head.
4. Hold the housing securely, then continue to rotate the spool in the spool reaches the bottom of the housing, the lines should snap out direction of the arrow an additional 1/4 inch or the width of the of the spool notches. channel to unlock the spool from the housing.
Draining the Fuel Tank and Carburetor TRANSPORTING WARNING Gasoline is highly flammable and explosive, and you can be Before Loading burned or seriously injured when refueling. If the engine has been running, allow it to cool for at least 15 minutes •...
Take the trimmer to an authorized ignition. Select a well-ventilated dry storage area away from any cable; throttle cable out of Honda dealer for repair. appliance that operates with a flame, such as a furnace, water heater, adjustment or bent.
5,000 feet (1,500 meters), have your servicing dealer perform this carburetor modification. This engine, when operated at high The emissions control systems on your new Honda engine were altitude with the carburetor modifications for high altitude use, will designed, built, and certified to conform with EPA, California, and meet each emission standard throughout its useful life.
Requires optional Barrier Kit no shims required Clutch Size 2.18 in (55.2 mm) 3.09 in (78.4 mm) Dimensions Engagement 4,200 ± 200 rpm Handle HHT25S HHT35S Drive Square female Installed Type Centrifugal Length Loop 73.4 in (1865 mm) 73.8 in (1875 mm)
FUEL SYSTEM MAINTENANCE When maintained properly, your Honda trimmer should provide years of trouble-free operation. This includes the fuel system. However, gasoline can quickly deteriorate, causing starting or running problems and, in some cases, damage to the fuel system. Most fuel-related problems can be avoided by following the precautions listed below.
The information and specifications included in this publication were in 72511-VF9-E00AH 22 tooth, 9” weed/brush effect at the time of approval for printing. American Honda Motor Co., 72511-VF9-D61 50 tooth, 10” weed/brush Inc. reserves the right, however, to discontinue or change...
Installing parts and accessories on non-Honda products or engines voids this warranty. American Honda will repair or replace, at its option, any part that is proven to be defective 2. You must be the first retail purchaser. This warranty is not transferable to subsequent in material or workmanship under normal use during the applicable warranty time period.
Control System Warranty, American Honda Motor Company Inc. and Honda Honda dealer determines it is defective or causes a failure of a warranted part, Canada Inc. will be referred to as Honda.
PRODUCT REGISTRATION Thank you for choosing Honda. To ensure you receive important service information in the event of a product update or recall, please register your trimmer within 30 days of purchase. From time to time, American Honda conducts sales promotions that require you to register your trimmer within 30 days of purchase.
1. Go to www.PowerEquipment.Honda.com to register your unit. 2. Click on Product Registration. 3. Complete the required information and click Submit. It’s that simple! NO POSTAGE NECESSARY Product Registration IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST-CLASS MAIL PERMIT NO.