Download Print this page

GE Z-Wave 45603 User Manual

Fluorescent & appliance module.
Hide thumbs

Advertisement

Wireless Lighting Control
Fluorescent &
Appliance Module
Z-Wave
Certified
®
Wireless Lighting Control
45603

Advertisement

   Related Manuals for GE Z-Wave 45603

No related manuals

   Summary of Contents for GE Z-Wave 45603

  • Page 1

    Wireless Lighting Control Fluorescent & Appliance Module Z-Wave Certified ® Wireless Lighting Control ™ 45603...

  • Page 2

    Z-Wave technology is designed to automate lighting/home control and provide easy remote operation of all your Z-wave enabled devices. The GE Z-Wave product family includes a variety of devices to control lighting in your home. It is up to you whether...

  • Page 3

    The device plugged into the Z-Wave controlled outlet on this module must not exceed 600 watts (Incandescent); 1800W (15A) Resistive or ½ HP Motor. Total load capacity for both outlets is 1800W (15A) Resistive. There are no user serviceable parts in this unit. Manual/Program button Standard AC outlet Z-wave outlet...

  • Page 4

    For these reasons, we recommend the following: Assign Z-Wave controlled appliances to device numbers 10 – 18 on the GE remote. The likelihood of unintentionally turning on the appliance will be reduced significantly because the “Shift” button will need to be pressed before pressing device numbers 10-18.

  • Page 5

    Z-Wave enabled devices installed in the control network. GE Z-Wave Network Every Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate “RF dead-spots”.

  • Page 6

    Effects of Home Construction on Wireless Range Between Z-Wave Enabled Devices. Note: The distances shown in the table below are typical examples. Actual performance in your home will vary. From the Remote (or repeating Z-Wave module) to destination device: Number of Walls or Obstacles * For Plug-in Modules or In-Wall Devices Installed in Plastic Junction...

  • Page 7

    Please Note: Z-Wave home control networks are designed to work properly alongside 802.11 wireless computer networks, Bluetooth and other 2.4GHz or 5.8GHz devices. Some baby cams, wireless video devices and older cordless phones using the 900MHz frequency range may cause interference and limit Z-Wave functionality. Many 900MHz products have a switch to select channel “A”...

  • Page 8: Manual Control

    Manual Control The Front Panel Push button on the 45603 Appliance Module allows the user to: Manually turn the connected equipment ON or OFF by pressing the button.

  • Page 9: Advanced Operation

    -Once the module is part of the network, the same basic procedure is used to add the module to groups or scenes. Refer to the primary controller’s instructions for details. Please Note: After a power failure, the 45603 module returns to its last used ON/OFF state. ADVANCED OPERATION...

  • Page 10

    Restoring Factory Defaults All Configuration Parameters can all be restored to their factory default settings by using your primary controller to reset the device. (delete it from network) Over-Current Protection Over-current protection is provided by an internal fuse which is not user serviceable. Check your home’s circuit breakers before concluding that the product must be replaced.

  • Page 11

    devices using the lighting control classification. The 45601 deluxe remote with LCD readout can control other Z-Wave certified devices like thermostats as well as lighting. WARRANTY JASCO Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase.

  • Page 12

    U2Z45602-3 The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 13

    RF exposure requirements and void user’s authority to operate the device. Compliance with IC Rules and Regulations IC: 6924A-45602A3 Jasco Products Company Model: 45603 ZW4101 This Class B digital device complies with Canadian ICES-003. SPECIFICATIONS Power 120VAC, 60Hz Signal (Frequency) 908.42 MHz...

  • Page 14

    General Electric Company and is used under license to Jasco Products Company LLC, 10 E Memorial Rd., Oklahoma GE SmartHome ™ City, Oklahoma 73114 Made in China Hecho en China All brand names shown are trademarks of their respective owners.

Comments to this Manuals

Symbols: 0
Latest comments: