Panasonic WV-SC588 Installation Manual page 10

Do not damage the power cable.
Do not damage, fabricate, twist, stretch, bundle, or forci-
bly bend the power cable. Do not place heavy objects on
it, and keep it away from heat sources.
Use of a damaged power cable may cause electric shock,
short circuit, or fire.
Consult the dealer for repair.
Correctly perform all wiring
Short circuits in the wiring or incorrect wiring may cause
fire or electrical shock.
Turn the power off when cleaning this product.
Failure to observe this may cause injury.
[Precautions for use]
This product is designed to be used indoors. This
product is not operable outdoors.
This product has no power switch.
When turning off the power, disconnect the power supply
from the 12 V DC power supply or the PoE device.
To keep on using with stable performance
Do not use this product in hot and humid conditions for a
long time. Failure to observe this causes component deg-
radation resulting in life shortening of this product. Do not
expose this product to direct heat sources such as a
heater.
Handle this product with care.
Do not drop this product, nor apply shock or vibration to
the product. Failure to observe this may cause trouble.
About the PC monitor
When displaying the same image on the monitor for a long
time, the monitor may be damaged.
It is recommended to use a screen-saver.
When an error is detected, this product will restart
automatically.
This product will be inoperable for around 2 minutes after
the restart just as when the power is turned on.
Product disposal/transfer
Data saved on this product or a storage device used with
this product may lead to personal information leakage.
When it is necessary to dispose or give this product to
someone, even when for repair, make sure that there is no
data on this product.
Do not hold the dome section.
The dome section of this unit rotates 360 °. When remov-
ing this unit from a ceiling or wall, turn the unit while hold-
ing the fixed section.
10
Cleaning this product body
Be sure to turn off the power before cleaning. Failure to
observe this may cause injury. Do not use strong abrasive
detergent when cleaning this product. Otherwise, it may
cause discoloration. When using a chemical cloth for
cleaning, read the caution provided with the chemical
cloth product.
IMPORTANT:
• The camera position may be moved inadvertently while
cleaning the camera body. Restart the camera or
refresh the camera position (position refresh) to correct
the camera position. Refer to the Operating Instructions
on the provided CD-ROM for further information.
Make sure that the product does not become wet.
Keep this camera away from water and moisture.
Transmission interval
Image transmission interval may become slow depending
on the network environment, PC performance, shooting
subject, access number, etc.
About SD memory card
• Before removing the SD memory card, make sure to
select "Not use" for "SD memory card" on the [SD
memory card] tab of "Basic" page on the setup menu
first. (☞ Operating Instructions (included in the
CD-ROM)) Refer to page 16 for descriptions of how
to insert/remove an SD memory card.
• When using an SD memory card, format it using this
product. Recorded data on the SD memory card will
be deleted when formatted. If an unformatted SD
memory card or an SD memory card formatted with
other devices is used, this product may not work
properly or performance deterioration may be caused.
Refer to the Operating Instructions on the provided
CD-ROM for how to format an SD memory card.
• When some SD memory cards are used with this
product, the product may not work properly or perfor-
mance deterioration may be caused. Use the SD
memory cards recommended in page 33.
Code label
The code labels (accessory) are required at inquiry for
trouble. Use caution not to lose these labels. It is recom-
mended to paste one of the labels onto the CD-ROM
case.
About the MOS image sensor
• When continuously shooting a bright light source such
as a spotlight, the color filter of the MOS image sen-
sor may become deteriorated and this may cause dis-
coloration. Even when changing the fixed shooting
direction after continuously shooting a spotlight for a
certain period, the discoloration may remain.
• When shooting fast-moving subjects or performing
panning/tilting operations, objects crossing the shoot-
ing area may look to be bending askew.