Northern Industrial Tools 998255 Owner's Manual
  1. Manuals
  2. Brands
  3. Northern Industrial Tools Manuals
  4. Mixer
  5. 998255
  6. Owner's manual

Northern Industrial Tools 998255 Owner's Manual

6 cu. ft. cement mixer
Hide thumbs
Table of Contents

Advertisement

Quick Links

6 CU. FT. CEMENT MIXER
OWNER'S MANUAL
WARNING:
Read carefully and understand all ASSEMBLY AND OPERATION
INSTRUCTIONS before operating. Failure to follow the safety rules and other
basic safety precautions may result in serious personal injury.
Item# 998255

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 998255 and is the answer not in the manual?

Questions and answers

Related Manuals for Northern Industrial Tools 998255

Summary of Contents for Northern Industrial Tools 998255

  • Page 1 6 CU. FT. CEMENT MIXER OWNER’S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item# 998255...

  • Page 2: Intended Use

    Thank you very much for choosing a Northern INDUSTRIAL Tools product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it.

  • Page 3: Work Area

    WORK AREA  Keep work area clean, free of clutter and well lit. Cluttered and dark work areas can cause accidents.  Do not use your tool where there is a risk of causing a fire or an explosion; e.g. in the presence of flammable liquids, gasses, or dust.

  • Page 4: Personal Safety

    CHART FOR MINIMUM WIRE SIZE OF EXTENSION CORD: Nameplate AMPS CORD LENGTH 100' 150' 18 AWG 16 AWG 16 AWG 14 AWG 6-10 18 AWG 16 AWG 14 AWG 12 AWG 10-12 16 AWG 16 AWG 14 AWG 12 AWG 12-16 14 AWG 12 AWG...
  • Page 5  Never start or stop the mixer with any material in the drum otherwise the motor will be damaged.  Never use a mixer with a malfunctioning switch. Any mixer that cannot be controlled with the switch is dangerous and must be repaired by an authorized service representative before using.
  • Page 6 (Recommend that 2 people assist in assembly) ASSEMBLY 1. Place Stand (#30) onto Hinge Bracket (#34) so that bolt holes line up as shown in Figure A. 2. Insert Hex Bolts (#26) with Washer (#27) through holes from one side, then Washer (#27) Lock Nut (#23) from the other side, and tighten with a wrench.
  • Page 7 Connect Seal (6) Fig. D Fig. E Drum Upper (4) Mixer Blade Mount holes 13. Move the Connect seal from the inside to make sure the holes of Drum Upper, Connector Seal, Drum Lower align in a line, insert the bolt (#58) with washer (#57) through the holes and rotate them by hand.
  • Page 8 17. Attach Degree Adjusting wheel (#20) to Iron Tube (#18) shaft as shown in Figure K: a. Insert coil spring into the lower hole. b. While holding the spring in place, slide the wheel over the iron tube. Note: The M8*25 bolt (#69) usually have been secured in place, this step may need a little exertion in order to compress the spring sufficient to be able to slip the wheel onto the Iron Tube.
  • Page 9 Fig. L Fig. M Bolt & Washer Bolt &Washer Fixed plate (38) Channels Washer &Locknut Channels Cushion (62) Inner Motor Base Cover (#39) Bolt &Washer Washer &Locknut Locknut (55) Motor Mount Plate (#40) 19. Mounting the Pulley and Belt(Figure N, O) Clean the Shaft (#35) of all plastic protective material and other debris.

  • Page 10: Operation

    Secure the Motor, slide Flat Washers on four Bolts (#41), then slide the Bolts up through the bottom of the Motor Mount Plate and the Motor. Secure in place with locknut. Check if Motor and belt turns true. Hands turn the Drum Pulley (#49) and verify that the Motor Pulley and Drum Pulley do not rub against any other part, and that the pulleys turn true.

  • Page 11: Maintenance

    MAINTENANCE WARNING: Make sure this tool is turned off and disconnected from its power source before attempting any maintenance, cleaning, or inspection.  It is recommended that the general condition of any tool be examined before it is used. Keep your tools in good repair by adopting a program of conscientious repair and maintenance in accordance with the recommended procedures found in this manual.
  • Page 12 DIAGRAM Page of 14...

  • Page 13: Parts List

    PARTS LIST Item# Description Item# Description Bolt M10×25 Motor mount plane Mixer Blade Bolt M8×20 Washer Φ10 Motor Drum Upper Motor base cover Lock Nut M10 Power cord Connector Seal Switch Bolt M6×12 Tap Screw M5×10 Drum lower Key C5×35 Gear ring Set Screw M5×10 Bearing sheath...
  • Page 14 WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints •...

Table of Contents