Advertisement
Operation Guide 3732
• The current time setting in accordance with the time calibration signal takes priority
over any time settings you make manually.
• The watch is designed to automatically update the date and day of the week for the
period January 1, 2000 to December 31, 2099. Setting of the date by the time
calibration signal cannot be performed starting from January 1, 2100.
• This watch can receive signals that differentiate between leap years and non-leap
years.
• Though this watch is designed to receive both time data (hour, minutes, seconds)
and date data (year, month, day), certain signal conditions can limit reception to time
data only.
• Normally, the signal reception date shown by the last signal screen is the date data
included in the received time calibration signal. When only time data is received,
however, the last signal screen shows the date as kept in the Timekeeping Mode at
the time of signal reception.
• If you are in an area where proper time calibration signal reception is impossible, the
watch keeps time within ±15 seconds a month at normal temperature.
• If you have problems with proper time calibration signal reception or if the time
setting is wrong after signal reception, check your Home Time Zone value and DST
(summer time) settings, and transmitter mode setting. The following are the initial
factory defaults for these settings.
Setting
Initial Factory Default
GMT Differential Value
–5.0 (or DST –4.0)
DST (summer time)
DS A (Auto switching)
Transmitter mode
W 60 (U.S. signal)
Transmitters
This watch is able to receive time calibration signals transmitted in the United States
(Fort Collins, Colorado) and Japan (Fukushima or Fukuoka/Saga). Selecting one of
the time zones as your Home Time Zone automatically configures the watch to receive
the applicable time calibration signal.
GMT Differential value
Transmitter
–5.0, –6.0, –7.0, –8.0
Fort Collins, Colorado
Fukushima
+9.0
Fukuoka/Saga
• When you have +9.0 (Japan) selected as your Home Time Zone, you can specify
either the Fukushima or Fukuoka/Saga transmitter, or you can configure the watch
to automatically select the transmitter that has the strongest signal.
• Selecting OFF for the transmitter mode setting disables auto receive.
To select the transmitter mode
1. In the Timekeeping Mode, press B to display the last
signal screen.
2. Hold down A until the transmitter mode setting starts
to flash, which indicates the setting screen.
• If holding down A does not display the setting
screen, check the current Home Time Zone setting.
Press B to return to the Timekeeping Mode screen.
See "To specify your Home Time Zone" for more
information.
3. Use B or D to select the transmitter mode setting you
want to use.
• When –5.0, –6.0, –7.0, or –8.0 is selected as the Home Time Zone, available
transmitter mode settings are W 60 (reception of the Fort Collins signal) and OFF
(auto receive off).
• The following are the available transmitter mode settings when +9.0 (Japan) is
selected as the Home Time Zone.
A: Automatic selection of the Fukushima or Fukuoka/Saga signal
J 40: Reception of the Fukushima signal
J 60: Reception of the Fukuoka/Saga signal
OFF: Auto receive off
4. Press A to exit the setting screen and return to the last signal screen.
• If you want to the return to the Timekeeping Mode screen, press B.
• Signal reception can take up to 14 minutes when the A option is selected.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The year can be set in the range of 2000 to 2099. The day of the week is calculated
automatically in accordance with the date.
• The watch's built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch's battery replaced or when battery power drops to
Level 4.
• The current time for all time zones in the Timekeeping Mode and Dual Time Mode is
calculated in accordance with the Greenwich Mean Time (GMT) differential of each
zone, based on your Home Time Zone time setting.
• GMT differential is calculated by this watch based on Universal Time Coordinated
(UTC
*
) data.
*
UTC is the world-wide scientific standard of timekeeping. It is based upon carefully
maintained atomic (cesium) clocks that keep time accurately to within
microseconds. Leap seconds are added or subtracted as necessary to keep UTC
in sync with the Earth's rotation. The reference point for UTC is Greenwich,
England.
12-hour/24-hour Timekeeping Formats
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is also
applied in all other modes.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
Power Saving
When turned on, Power Saving automatically enters a sleep state whenever the watch
is left for a certain period in an area where it is dark. The table below shows how
watch functions are affected by Power Saving.
• There are actually two sleep state levels: "display sleep" and "function sleep".
Elapsed Time in Dark
3 to 4 days
Digital display off, but all functions enabled
(Display Sleep)
• Digital display off
8 days or more
• All functions, including analog timekeeping, disabled
(Function Sleep)
• Internal timekeeping maintained
• Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.
Frequency
60kHz
40kHz
60kHz
Operation
To recover from the sleep state
Perform any one of the following operations.
• Move the watch to a well-lit area. It can take up to two seconds for the display to turn
on.
• Press any button.
• Angle the watch towards your face for reading.
To turn Power Saving on and off
1. While any screen other than the last signal screen is on
the display in the Timekeeping Mode, hold down A
until the GMT differential value starts to flash, which
indicates the setting screen.
2. Press C nine times until the Power Saving on/off
|
screen appears.
3. Press D to toggle Power Saving on (on) and off (OFF).
4. Press A to exit the setting screen.
Adjusting Dial Hand Positions
You can use the procedure in this section to adjust the position of the stopwatch 1/20
second dial hand and the battery level dial hand whenever they do not align with the
12 o'clock position when you enter the Stopwatch Mode.
Important!
Stopwatch 1/20
Never move the battery level dial hand to any position
second dial
other than 12 o'clock. If you do, it will not correctly indicate
the battery power level.
To adjust dial hand positions
1. In the Timekeeping Mode, press C five times to enter
the Hand Setting Mode.
2. Hold down A until – 0 0 – starts to flash, which
indicates the analog setting screen.
3. Press A to display the dial hand setting screen.
• The dial hand setting screen shows 00:00.00, with the
two zeros on the far right flashing. This indicates that
Battery level dial
the stopwatch 1/20 second dial is selected for
adjustment.
4. Press D to advance the hand of the stopwatch 1/20 second dial one step, until it is
aligned with the 12 o'clock position.
5. After the 1/20 second dial hand is aligned properly, press C.
• This causes the two far left zeros of the 00:00.00 figures to flash, which indicates
that the battery level dial is selected for adjustment.
6. Press D to advance the hand of the battery level dial one step, until it is aligned
with the 12 o'clock position.
7. Press A to exit the setting screen.
• To return to the Timekeeping Mode, press C.
Illumination Precautions
• The illumination provided by the light may be hard to see when viewed under direct
sunlight.
• Illumination automatically turns off whenever an alarm sounds.
• Frequent use of illumination shortens the battery operating time.
Auto light switch precautions
• Wearing the watch on the inside of your wrist, movement of your arm, or vibration of
your arm can cause frequent activation of the auto light switch and illuminate the
face of the watch. To avoid running down the battery, turn off the auto light switch
whenever engaging in activities that might cause frequent illumination of the face.
• Note that wearing the watch under your sleeve while the auto light switch is turned
on can cause frequent illumination of the face and can run down the battery.
• Illumination may not turn on if the face of the watch is
More than 15 degrees
more than 15 degrees above or below parallel. Make
too high
sure that the back of your hand is parallel to the ground.
• Illumination turns off after about two seconds, even if
you keep the watch pointed towards your face.
• Static electricity or magnetic force can interfere with
proper operation of the auto light switch. If illumination
does not turn on, try moving the watch back to the
starting position (parallel with the ground) and then tilt it
back towards your face again. If this does not work, drop
your arm all the way down so it hangs at your side, and
then bring it back up again.
• Under certain conditions, illumination may not turn on until about one second after
you turn the face of the watch towards you. This does not necessarily indicate
malfunction of the auto light switch.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
Tachymeter
If your watch has a tachymeter bezel, you can perform the
Tachymeter bezel
steps below to calculate average speed after using the
Stopwatch Mode to measure the amount of time that it
60
takes to travel one kilometer (or one mile).
• Never try to perform stopwatch operations while you
are driving an automobile, riding a bicycle, or
operating any type of vehicle. Doing so is very
dangerous and can result in accident.
1 In the Stopwatch Mode, start an elapsed time
operation at any point you like.
2 Stop the elapsed time operation after you travel one
kilometer or one mile.
3 Your average speed will be the value that the second
hand is pointing to on the tachymeter bezel.
• The illustration shows an example where it took 50 seconds to travel one kilometer
by car. The second hand is pointing at 70, which indicates that the average speed is
70 kilometers per hour.
• See "Stopwatch" for details about using the stopwatch.
• The tachymeter can be used only when you are traveling by car or some other
means that can cover one kilometer or one mile within 60 seconds.
6
Advertisement
