Casio 1138 Operation Manual

MO0310-EA
General Guide
• You can use the Remote Control functions while in the Timekeeping Mode.
A
B
P
C
– +
– +
[ Module No. 1173 ]
The operational procedures for Modules 1138 and 1173 are identical. All of
the illustrations in this manual show Module 1138.
Timekeeping Mode
Signal Emitter
Month
Day of week
Date
A
POWER
TV/VCR
B
P
STOP
C
PLAY
Seconds
Minutes
Hour
PM indicator
About the Timekeeping sub-modes
The Timekeeping Mode is actually made up of three sub-modes. Use the A button
while in the Timekeeping Mode to switch between the sub-modes.
A
B
P
C
Normal Timekeeping Mode
About the remote control function
In order to be able to use this watch for remote control of a television or video tape
deck, you must first set the appropriate manufacturer code. The manufacturer code
tells the watch what signals to use for remote control. The Manufacturer Code Table
shows the names of the manufacturers that correspond to each code. For full details
on how to actually set the manufacturer code, see "To set the manufacturer code".
Some TV or tape deck models may not work properly with this watch, even
though they are made by one of the manufacturers in the Manufacturer Code
Table. Also, you may find that you can control a TV or tape deck using a code
for a manufacturer that is different from the ones in the table. For details on
finding the code you should use, see "How to find the right code".
Note
• Replacing the battery will cause the remote control data setting (TV/video
manufacturer codes) to be altered. Be sure that you make a note of your codes
before you have the battery replaced.
• There are some manufacturers with more than one code. Try the various codes
available for your equipment to find the one that works best.
• You have to set separate codes for your TV and tape deck, even if they are made by
the same manufacturer.
• You might not be able to use this watch to control models that combine a TV and
tape deck into a single unit, multi-functional TVs that can be used as computer
monitors, or other televisions or tape decks equipped with special functions.
Manufacturer code (TV/Cable Box)
Code
Manufacturer
18
GE
21
GE
GOLDSTAR 29
HITACHI 28
JERROLD (C)* 8
9
JERROLD (C)*
30
JVC
JVC 31
JVC 32
MAGNAVOX 22
MAGNAVOX 23
MAGNAVOX 24
34
MAGNAVOX
* "(C)" indicates cable box.
Operation Guide 1138 1173
Timekeeping Mode
A
POWER
TV/VCR
B
P
STOP
C
PLAY
[ Module No. 1138 ]
In addition to normal timekeeping, the Timekeeping
Mode also provides you with remote control capabilities
for your TV* or video tape deck.
* The terms "TV" and "television" as used in this
manual refer to both standard televisions and the
cable box of cable TV systems.
• This watch will control only televisions and video tape
decks that are equipped with remote control sensors.
• For details on how to set the time and date, see "Time
Setting Mode".
Note
The remote control buttons of the watch are marked
according to their functions. In this manual, the buttons
are referred to by using their marking in bold
characters.
Example: Press POWER to switch on the television.
Other (unmarked) buttons are indicated using the
letters A, B, and C, as shown in the illustration.
Press A.
TV
TV
P P
TV Mode Video Mode
(for television remote (for video tape deck
control) remote control)
Manufacturer Code
Manufacturer
14
MITSUBISHI SAMSUNG
15
MITSUBISHI SCIENTIFIC ATLANTIC (C)*
MITSUBISHI 37 SCIENTIFIC ATLANTIC (C)*
PANASONIC 12 SHARP
PANASONIC 33 SONY
PANASONIC (C)* 13
TOSHIBA
PHILIPS 39
TOSHIBA
PIONEER (C)* 25 ZENITH
RCA 1 ZENITH (C)*
RCA 2
RCA 36
SAMSUNG 16
17
SAMSUNG
• Press C to change from mode to mode. Each mode is explained in detail in the
following sections.
• After you perform an operation in any mode, pressing C returns to the Timekeeping
Mode.
Stopwatch Mode
Manufacturer
GE
GOLDSTAR
GOLDSTAR
HITACHI
HITACHI
JVC
JVC
JVC
JVC
MITSUBISHI
MITSUBISHI
PANASONIC
PANASONIC
To set the manufacturer code
TV Mode indicator
Signal Emitter
A
POWER
TV/VCR
SET TV
B
STOP
C
PLAY
Manufacturer code
6. When you have the correct manufacturer code, press B to return to the
Timekeeping Mode.
• See "To use the remote control functions" for information on using the remote control
functions.
• If you can't find a code that works with your equipment, see "How to find the right
code".
• If you do not press any buttons for a few minutes while the manufacturer code is
flashing, the flashing will stop and the watch automatically returns to the
Timekeeping Mode.
How to find the right code
Use the following operation if you have difficulty finding a manufacturer code that
works with your equipment.
1. Switch on the TV or video tape deck whose manufacturer code you want to set.
2. In the Timekeeping Mode, hold down B until a manufacturer code appears flashing
Code
on the display.
20
3. Press A to select either the TV Mode (
10 Mode ( indicator shown on the display).
4. Press until manufacturer code 01 appears.
11
• Code 01 comes sequentially after code 39.
19
• Holding down
increases the code number at high speed.
3
5. To test whether or not the displayed manufacturer code is correct for your
equipment, point the Signal Emitter (red window) at your TV or tape deck and press
26
POWER. Note that the TV/tape deck should be switched on.
27
• If the above operation switches the power of your TV or tape deck off, it means that
6
the correct code has been selected. Skip to step 6.
• Certain TVs and tape decks may be slow to respond after receiving a remote control
7
signal. With such units, try holding down POWER for one or two seconds.
4
• If nothing happens when you press POWER, press
5
and repeat step 5 to test the code.
35 • Note that some codes in the Manufacture Code Table do not have manufacturer names.
The watch does not emit remote control signals while these codes are set, and so
38
you should not use them.
6. After you have found the correct manufacturer code, press B to return to the
Timekeeping Mode.
Alarm Mode Time Setting Mode
P
Manufacturer code (video tape deck)
Code Manufacturer Code Manufacturer
21 PHILIPS 38 TOSHIBA
28 PHILIPS 39 ZENITH
29 RCA 1
22 2
RCA
23 36
RCA
30 SAMSUNG 16
31 SAMSUNG 17
32 SHARP 19
35 SHARP 20
15 SONY 3
37 4
SONY
12 SONY 5
33 TOSHIBA 26
1. Switch on the TV or video tape deck whose
manufacturer code you want to set.
2. In the Timekeeping Mode, hold down B until a
manufacturer code appears flashing on the display.
3. Press A to select either the TV Mode (
shown on the display) or Video Mode (
shown on the display).
4. Press to increase the code number.
• Holding down
increases the code number at high
speed.
• See the Manufacturer Code Table for details on
manufacturer codes.
5. To test whether or not the displayed manufacturer code
is correct for your equipment, point the Signal Emitter
(red window) at your TV or tape deck and press
POWER. Note that the TV/tape deck should be
switched on.
• If the above operation switches the power of your TV or
tape deck off, it means that the correct code has been
selected.
• Certain TVs and tape decks may be slow to respond after
receiving a remote control signal. With such units, try
holding down POWER for one or two seconds.
• If nothing happens when you press POWER, use steps 4
and 5 to try another code.
indicator shown on the display) or Video
TV
to advance to the next code
SET
Code
27
6
7
8
9
10
11
13
14
18
24
25
34
indicator
TV
indicator
1