Download Print this page

Casio 1138 Operation Manual page 2

Advertisement

Operation Guide 1138 1173
To use the remote control functions
1. In the Timekeeping Mode, press A to select either the
Signal Emitter
TV Mode (
TV mode
Indicator
Mode (
indicator
2. Point the Signal Emitter (red window) at your TV or tape
deck and use the buttons on the right side and the
bottom of the watch to perform the operation that you
want (see the table below).
A
POWER
• Each time you perform an operation, an indicator
TV/VCR
B
appears on the display to show which operation is being
TV
P
STOP
performed.
C
PLAY
TV Mode
Button
Operation
Indicator
Switches power on and off
POWER
TV/VCR
Switches between TV and
video function
No function
STOP/
PLAY/
No function
+
Changes to the next higher
/
channel
L
/
Increases volume
M
Decreases volume
/
Changes to the next lower
/
channel
Note
• This watch is equipped with buttons that cover as wide a range of remote control
functions as possible. Note, however, that if your TV or tape deck is not equipped
with some of these functions, nothing will happen when you press the corresponding
button on this watch.
• For televisions that do not have a TV/video switching function, pressing the TV/VCR
button may switch teletext, etc. on and off.
Troubleshooting Guide
Problem: Remote control functions do not work at all.
• Possible Cause: Use of the wrong mode (TV/Video)
Action: Make sure the watch is in the TV Mode when you are trying to control a
TV, or in the Video Mode when you are trying to control a video tape
deck. See "About the Timekeeping sub-modes" for details on changing
modes. You cannot control any other remote control device (besides a
TV or video tape deck) using this watch.
• Possible Cause: Wrong manufacturer code
Action: You must set the correct manufacturer code for the type of TV or video
tape deck you are trying to control. See "To set the manufacturer code".
• Possible Cause: The path between the signal emitter and TV/video tape deck is
blocked or too long (more than 16 feet/5 meters).
Action: Make sure that the path between the watch's signal emitter and the
signal receiver on your TV or tape deck is not blocked by clothing, your
hand, furniture, etc. Reduce the distance between the signal emitter and
TV/video tape deck if necessary.
Problem: Some remote control functions do not work.
• Possible Cause: Too much distance between the watch and TV/video tape deck,
or improper pointing of the watch's signal emitter.
Action: The distance between the watch and TV/video tape deck should be less
than 16 feet/5 meters. Also, make sure that the signal emitter is pointing
directly at the TV/video tape deck when you are performing a remote
control function.
• Possible Cause: Use of button on the watch for which the TV/video tape deck does
not have a corresponding function.
Action: Some TV or tape deck models may not have functions that correspond to
the functions provided on the watch.
Problem: Video deck functions do not work at all.
• Possible Cause: Your video tape deck might have a dual code (A Code/B Code or
Video 1/Video 2) remote control receiver.
Action: Try switching the setting (between A Code/B Code or Video 1/Video 2)
on your video tape deck until you find the correct setting for use with the
watch.
Stopwatch Mode
Mode indicator
The Stopwatch Mode lets you measure elapsed time, split
times, and two finishes. The range of the stopwatch is 23
hours, 59 minutes, 59 seconds.
A
(a) Elapsed time measurement
A
A
B
Start
C
(b) Split time measurement
A
B
Start
Seconds
Hours
(c) Split time and 1st-2nd place times
A
B
Start
Minutes
First runner
finishes.
indicator shown on the display) or Video
TV
indicator shown on the display).
Video Mode
Operation
Indicator
Switches power on and off
Switches between TV and
video function
Stops tape transport
Starts tape playback
Changes to the next higher
channel
Starts fast forward operation
Start rewind operation
Changes to the next lower
channel
A
A
B
Stop
Re-start
Stop
Clear
B
A
B
Split
Split release
Stop
Clear
A
B
B
Split
Stop
Split release
Clear
Second runner
Record time of
finishes.
second runner.
Record time of
first runner.
Alarm Mode
When the Daily Alarm is switched on, the alarm sounds for
Hourly time signal
20 seconds at the preset time each day. Press any button
on indicator
to stop the alarm after it starts to sound.
Mode indicator
When the Hourly Time Signal is switched on, the watch
beeps every hour on the hour.
A
To set the alarm time
1. Hold down B while in the Alarm Mode until the hour
B
digits start to flash on the display. The hour digits flash
because they are selected .
C
• This operation will switch the Daily Alarm on
automatically.
2. Press L to change the selection in the following
sequence.
Alarm on
Hour
indicator
Hour
Minutes
to increase the selected digits. Holding down
3. Press
high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select for
normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon (P).
4. After you set the alarm time, press B to return to the Alarm Mode.
To switch the Daily Alarm and Hourly Time Signal on and off
Press A while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
[ Alarm on indicator/Hourly Time Signal on indicator ]
Both ON
Both OFF
To test the alarm
Hold down A while in the Alarm Mode to sound the alarm.
Time Setting Mode
To set the time and date
Month
1. Use C to enter the Time Setting Mode.
• The seconds digits flash, because they are selected .
Date
Day of week
2. Press L to change the selection in the following
sequence.
A
Seconds
B
SET
P
C
Day of Week
• While the selection is flashing, press A to switch
Seconds
between 12-hour and 24-hour formats.
Hour
Minutes
PM indicator
3. While the seconds digits are selected (flashing), press
"00". If you press
while the seconds count is in the range of 30 to 59, the
seconds are reset to "00" and 1 is added to the minutes. If the seconds count is in
the range of 00 to 29, the minutes count is unchanged.
4. While any other digits (besides seconds) are selected (flashing), press
increase the number. While the day of the week is selected, pressing
to the next day. Holding down
changes the current selection at high speed.
5. After you set the time and date, press C to return to the Timekeeping Mode.
• The watch does not make any allowance for leap years. Be sure to manually set
February 29 (when one occurs) for the appropriate date.
• If you do not press any buttons for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
Minutes
increases the selection at
Daily Alarm
Hourly Time
only
Signal only
Hour
Minutes
Date
Month
to reset the seconds to
to
advances
2

Advertisement

loading

This manual is also suitable for:

1173