Table of Contents
Advertisement
Quick Links
USER'S MANUAL
Of
GeForce6100 GPU
&
nForce 410 MCP
M/B For Socket AM2 64-bit Dual Core
AMD Processor
NO. G03-M2GT3-FR111
Rev:1.0
Release date: June 2006
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Advertisement
Table of Contents
Related Manuals for Mach Motherboard
Summary of Contents for Mach Motherboard
- Page 1 USER'S MANUAL GeForce6100 GPU & nForce 410 MCP M/B For Socket AM2 64-bit Dual Core AMD Processor NO. G03-M2GT3-FR111 Rev:1.0 Release date: June 2006 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
- Page 2 Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding. To minimize pollution and ensure environment protection of mother earth, please recycle.
-
Page 3: Table Of Contents
EXPANSION CARD ......................11 2-5-1 PROCEDURE FOR EXPANSION CARD INSTALLATION ......11 2-5-2 ASSIGNING IRQ FOR EXPANSION CARD ............11 2-5-3 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD ...... 12 2-5-4 PCI-Express SLOT ....................12 CONNECTORS, HEADERS....................13 2-6-1 CONNECTORS ......................13 2-6-2 HEADERS ........................ -
Page 4: Manual Revision Information
BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE GEFORCE 6100 GPU MOTHERBOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS”... -
Page 5: Chapter 1 Introduction Of Geforce 6100 Gpu Motherboards
Introduction of GeForce 6100 GPU Motherboards 1-1 Features of motherboard The GeForce 6100 GPU motherboard series are based on the latest NVIDIA GeForce 6100 GPU (C51G) chipset and NVIDIA nForce 410 MCP (MCP51G ) chipset which supports the innovative and supercharged new generation 64-bit AMD Socket AM2 Athlon64 and Sempron processors with HyperTransport Technology up to 1000MHz. -
Page 6: 1-1.1 Special Features Of Motherboard
Some special features---CPU Thermal Throttling/ CPU Vcore 7-shift/ CPU Smart Fan in this motherboard are designed for power user to use the over-clocking function in more flexible ways. But please be caution that the over-clocking maybe cause the fails in system reliabilities. -
Page 7: Specification
1-2 Specification Spec Description ∗ ATX form factor 4 layers PCB size: 24.4*22.3cm Design ∗ Chipset NVIDIA GeForce 6100 Graphic Processing Unit Chipset (C51G) ∗ NVIDIA nForce 410 Media and Communication Processor Chipset(MCP51G) ∗ Support 64bit AMD Athlon64 940-Pin package utilizes Flip- CPU Socket AM2 Chip Pin Grid Array package processor ∗... -
Page 8: Performance List
1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report CPU:... -
Page 9: Layout Diagram & Jumper Setting
1-4 Layout Diagram & Jumper Setting Rear I / O for GeForce 6100 GPU Motherboard Type 1 10/100 PRINTER COM1 Mbps LAN Line-IN PS/2 Mouse Line-OUT PS/2 Keyboard MIC-IN USB1 Rear I / O for GeForce 6100 GPU Motherboard Type 2... -
Page 10: Expansion Sockets
Jumpers Jumper Name Description Page JBAT CMOS RAM Clear 3-pin Block Keyboard/USB Power On Enabled/Disabled 3-pin Block USB Power On Enabled/Disabled 3-pin Block Connectors Connector Name Description Page ATX Power Connector 24-pin Block P.13 ATXPWR ATX12V ATX 12V Power Connector 8-pin Block P.13 PS/2 Mouse &... -
Page 11: Chapter 2 Hardware Installation
2-2 Checking Motherboard’s Jumper Setting (1) CMOS RAM Clear (3-pin) : JBAT A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2 pins of JBAT to store the CMOS data. To clear the CMOS, follow the procedure below:... -
Page 12: Install Cpu
RAM, I/O devises, and adapter cards. Processor slot/socket - the slot or socket used to mount the system processor on the motherboard. Slot (PCI-E, PCI, RAM) - the slots used to mount adapter cards and system RAM. -
Page 13: About Amd Athlon64 940-Pin Cpu
Flip-Chip Pin Grid Array package technology. The CPU that comes with the motherboard should have a cooling FAN attached to prevent overheating. If this is not the case, then purchase a correct cooling FAN before you turn on your system. -
Page 14: Install Memory
DIMM1 & DIMM2, or DIMM3 & DIMM4 must be the same type, same size, same frequency for dual channel function. Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer to figure 2-4 to see what a 240-Pin DDRII400/DDRII533/DDRII667/DDRII800 DDRII SDRAM module looks like. -
Page 15: Expansion Card
Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2-5-1 Procedure For Expansion Card Installation 1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers. -
Page 16: Interrupt Request Table For This Motherboard
2-5-3 Interrupt Request Table For This Motherboard Interrupt request are shared as shown the table below: INT A INT B INT C INT D INT E INT F INT G INT H √ Slot 1 √ Slot 2 √ Onboard USB 2 √... -
Page 17: Connectors, Headers
2-pins Power On jumper pole on the motherboard. When the power switch on the back of the ATX power supply turned on, the full power will not come into the system board until the front panel switch is momentarily pressed. - Page 18 PS/2 Mouse & PS/2 Keyboard Connector: KB The connectors for PS/2 keyboard and PS/2 Mouse. USB Port connector: USB1 The connectors are 4-pin connector that connect USB devices to the system board. LAN Port connector: UL1 (Option) This connector is standard RJ45 connector for Network The USBLAN1 support 10M/100Mb/s data transfer rate Parallel Port Connector (25-pin female): PARALLEL Parallel Port connector is a 25-pin D-Subminiature Receptacle connector.
- Page 19 (10) Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives. Pin 1 Floppy Drive Connector (11) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable.
- Page 20 IDE channel as a hard disk. Otherwise, the system performance on this channel may drop. (13) Serial-ATAII Port connector: SATAII1 / SATAII2 This connector supports the provided Serial ATA2 IDE hard disk cable to connecting the motherboard and serial ATAII hard disk. SATAII1 SATAII2 Serial-ATAII 1 & 2 Compatible Connectors...
-
Page 21: Headers
2-6-2 Headers Line-Out/MIC Header for Front Panel (9-pin): AUDIO This header connect to Front Panel Line-out, MIC connector with cable. Without install the cable, this header default setting is 5-6 short, 9-10 short. When you install the cable you have take off these jumpers. AUDIO Pin 1 Line-Out, MIC Headers... - Page 22 Power switch: PWR BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. PWRLED Pin 1 JW FP SPEAK Pin 1 Pin 1 System Case Connections FAN Headers (3-pin) : SYSFAN1, SYSFAN2, CPUFAN These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different.
- Page 23 CD Audio-In Headers (4-pin) : CDIN CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. C DIN CD Audio-In Headers (10) COM2 Port: COM2(O ption ) Com2 is for the serial devices, such as the joystick, the scanner and so on. (11) TV-OUT Header: TV-OUT(O ption ) This 10 pin connector is for the TV-out port module that allows you to connect a television to your system.
-
Page 24: Starting Up Your Computer
2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used. -
Page 25: Chapter 3 Introducing Bios
Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. -
Page 26: The Main Menu
3-3 The Main Menu Once you enter Award ® BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. -
Page 27: Standard Cmos Features
Power User Overclock Settings Use this menu to specify your settings (frequency, Voltage) for overclocking demand Password Settings This entry for setting Supervisor password and User password Load Optimized Defaults Use this menu to load the BIOS default values these are setting for optimal performances system operations for performance use. -
Page 28: Advanced Bios Features
SATA Channel 1, 2, 3, 4 Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If the type of hard disk drives is not matched or listed, you can use Manual to define your own drive type manually. - Page 29 Virus Warning Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
-
Page 30: Advanced Chipset Features
Typematic Rate (Chars/Sec) Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30. Typematic Delay (Msec) Sets the delay time after the key is held down before is begins to repeat the keystroke. The settings are 250, 500, 750, and 1000. -
Page 31: Dram Timing Settings
3-6-1 DRAM Configuration Phoenix – AwardBIOS CMOS Setup Utility DRAM Timing Settings Auto Configuration Auto Item Help DRAM CAS Latency Auto Min RAS# active Time<Tras> Auto Row precharge Time<Trp> Auto Menu Level >> RAS# to CAS# Delay<Trcd> Auto DRAM Bank Interleaving Disabled Memory Hole Remapping Enabled... -
Page 32: Integrated Peripherals
3-7 Integrated Peripherals Phoenix – AwardBIOS CMOS Setup Utility Integrated Peripherals > Onchip IDE Function Press Enter Item Help > Onchip Device Function Press Enter > Onchip super IO Function Press Enter Init Display First PCI Slot Menu Level > ↑↓→←... -
Page 33: Onchip Device Function
The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device. -
Page 34: Onchip Super Io Function
3-7-3 Onchip Super IO Function Phoenix – AwardBIOS CMOS Setup Utility Onboard Super IO Function Onboard FDC Controller Enabled Item Help Onboard Serial Port 2 2F8/IRQ3 Onboard Parallel Port 378/IRQ7 Parallel Port Mode Menu Level >> ECP Mode Use DMA ↑↓→←... -
Page 35: Power Management Setup
3-8 Power Management Setup The Power Management Setup allows you to configure your system to most effectively save energy saving while operating in a manner consistent with your own style of computer use. Phoenix – AwardBIOS CMOS Setup Utility Power Management Setup PS2 KB/MS Wakeup by<S3/S4/S5>... -
Page 36: Miscellaneous Control
3-9 Miscellaneous Control This section is for setting CPU Frequency/Voltage Control. Phoenix – AwardBIOS CMOS Setup Utility Miscellaneous Control CPU Spread Spectrum Disabled Item Help PCIE Spread Spectrum Disabled SATA Spread Spectrum Disabled HT Spread Spectrum Disabled Menu Level > Reset Configuration Data Disabled IRQ Resources... -
Page 37: Pc Health Status
3-10 PC Health Status This section shows the Status of you CPU, Fan, Warning for overall system status. This is only available if there is Hardware Monitor onboard. Phoenix – AwardBIOS CMOS Setup Utility PC Health Status Show H/W Health in Post Enabled Item Help Shutdown Temperature... -
Page 38: Thermal Throttling Options
CPU/SFAN1 Smart FAN Full-Speed Temp This item allows you setting the FAN works in full speed when the temperature over the value which out set. If the temperature below the value but over the Idle Temperature, the FAN will works over 60% of full speed, and the higher temperature will gain higher FAN speed, after over the temperature which this item setting, the FAN works in full speed. -
Page 39: Power User Overclock Settings
Phoenix – AwardBIOS CMOS Setup Utility Thermal Throttling Options CPU Thermal-Throttling Disabled Item Help CPU Throttling Temp CPU Throttling Duty 87.50% CPU Throttling Beep Enabled Menu Level > CPU Throttling Duty 87.50% ．．．．．[ 75.00% ．．．．．[ 62.50% ．．．．．[ 50.00% ．．．．．[ 35.50% ．．．．．[ 25.00% ．．．．．[ 12.50% ．．．．．[ ↑↓→←... -
Page 40: Cpu Vcore
CPU/DRAM Clock at next Boot is This item allows you change the CPU Host /DRAM clock for overclock demand. When the CPU Host clock is over the CPU default value BIOS will auto disabled Bi-Turbo function. CPU Vcore This item allows you select the CPU Vcore Voltage xx% more than the standard value, by this function for the precise over-clocking for extra demanding of performance. -
Page 41: Password Settings
3-13 Password Settings Phoenix – AwardBIOS CMOS Setup Utility Password Settings Item Help Set Supervisor Password Press Enter Set User Password Press Enter Menu Level > ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults You can set either supervisor or user password, or both of them. -
Page 42: Chapter 4 Driver & Free Program Installation
Chapter 4 DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. -
Page 43: Nforce Install Nforce Integrated Driver
Install nForce Integrated Driver nForce * nForce Integrated driver pack include following device driver: NVIDIA GART driver : If you are using an AGP VGA Card, please install NVIDIA AGP GART driver which provides service routines to your VGA driver and interface directly to the hardware for speedy graphic access. - Page 44 5. Please choose to install the NVIDIA firewall 6. If you want to install NVIDIA firewall and and Forceware Network Access Manager Forceware Network Access Manager utility Utility Driver for demanding on you own. 7. Select install complete software and Click 8.
-
Page 45: Sound Install Alc655 6-Channel Audio Driver
ALC655 6-Channel 4-2 SOUND install Audio Driver 1. Click SOUND when MAGIC INSTALL 2. Click NEXT When Realtek AC97Audio driver MENU appears windows appears 3. Click FINISH and restart your computer 4. Manual Sound Effect Setting 5. Speaker configuration setting 6. -
Page 46: Lan
Install Optional Realtek LAN Controller Driver 4-3 LAN WINDOWS 2000/XP Setup 1. Click LAN when Magic Install Menu appear 2. Click NEXT, install REALTEK LAN and Fast Ethernet NIC Driver 3. After driver installation completed, Click Finish USB2.0 Install Intel USB2.0 DRIVER Windows 2000 OS Please install Windows 2000 service pack 4 or later . -
Page 47: Pc-Cillin Install Pc-Cillin 2006 Anti-Virus Program
4-5 PC-CILLIN Install PC-CILLIN 2006 Anti-virus program Click PC-CILLIN when MAGIC INSTALL Please select “Install program” when the MENU appears "Trend Micro internet security" installshield wizard windows appears This is license agreement, select "I Accept Click NEXT or choose Change to change the the terms"... -
Page 48: Pc-Health Install Myguard Hardware Monitor Utility
PC-HEALTH Install MyGuard Hardware monitor Utility 1. Click PC-HEALTH when MAGIC INSTALL 2. Click Next when Install shield wizard Window MENU appears appears, Choose destination location and click Next, when the start copy file windows appear, click next 3. Select Finish after setup complete 4. -
Page 49: How To Update Bios
STEP 2. Copy utility program to your boot disc. You may copy from DRIVER CD X:\FLASH\AWDFLASH.EXE or download from our web site. STEP 3. Download and make a copy of the latest BIOS for GeForce 6100 GPU motherboard series from the web site to your boot disc. - Page 50 Step 2. After the System boot up in the second page , you can find the NVIDIA RAID IDE ROM BIOS windows appear. It will ask you to “Press F10 to enter RAID setup utility …“ ? Please press “F10” key to RAID utility now , then you can select the RAID functions on your own with the optional RAID functions as below, 1.
-
Page 51: Pro Magic Plus Function Introduction
Windows 2000 for the proper installation. Execute Start programs NVIDIA corporation RAID manager , you can view RAID function status or rebuild RAID function from Windows OS 4-9 Pro Magic Plus Function Introduction What’s Pro Magic Plus? Tired with reinstall OS each time when it doesn’t work? Does your computer often crash down or unable to work after installed new software? Have you had great loses and troubles because of computer problems? Still using time-consuming backup software that occupies lots of HD space? - Page 52 Multipoint Save/Restore – You can backup your system whenever you need and restore them back to anytime you wish, 1 hour, 1 day or 1 month ago. Restore points are unlimited. (disable item for OEM version) Data Disk Protection – Pro Magic Plus now comes with data disk protection, provides complete protection for your computer! (disable item for OEM version) You can choose to change the default path of ‘My Document’, ‘My Favorite’...
Need help?
Do you have a question about the Motherboard and is the answer not in the manual?
Questions and answers