Related Manuals for Panasonic PT-FX400
Summary of Contents for Panasonic PT-FX400
- Page 1 PT FX400 P ro d u c t N u m b e r : LCD Projector P ro d u c t N a m e : As of March 2011. Specifications and appearance are subject to change without notice. 1 / 1 3 SFL11M006-1...
-
Page 2: Specifications
PT-FX400 LCD Projector Specifications Main unit Power supply 100 –240 V AC, 3.9 –1.4 A, 50/60 Hz Power consumption 330 W (0.3 W at 100 –120 V AC, 0.4 W at 220 – 240 V AC when standby mode set to eco,* 9 W when standby mode set to normal, 20 W when standby mode set to normal and audio monitor out.) -
Page 3: Wireless Module
PT-FX400 LCD Projector DVI-I IN* DVI-I 29-pin × 1 Digital DVI 1.0 compliant, compatible with HDCP, compatible with single link only 480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p, 1080 (1125)/60i, 1080 (1125)/50i, 1080 (1125)/24p, 1080 (1125)/60p, 1080 (1125)/50p VGA (640 × 480) – WSXGA + (1,680 × 1,050), compatible with non- interlaced signals only, dot clock: 25 .2 MHz –146.25 MHz... -
Page 4: Lcd Projector
PT-FX400 LCD Projector Wireless Manager ME 5.5 system requirements To use network functions, a PC is required that meets the conditions given below. ® Microsoft Windows ® Professional 32-bit, Home Edition 32-bit, Tablet PC Edition 2005 32-bit Windows Vista ®... - Page 5 PT-FX400 LCD Projector Dimensions unit : mm (inch) NOTE: This illustration is not drawn to scale. 228.5 (2-3/32) ( 9 ) (16-15/16 ) Terminals LAN connector HDMI input S-VIDEO IN DVI-I IN COMPUTER IN DVI-I input Computer input VIDEO VARIABLE...
-
Page 6: Standard Setting-Up Position
PT-FX400 LCD Projector Standard setting-up position ** Adjustable in 20 mm (25/32˝) steps. ∅49 (1-15/16) ∅42 (1-11/16) Upper edge of projected image Projected image (7-5/8) Lower edge of projected image NOTE: Illustrations show the projector installed using optional ceiling mount bracket ET-PKF110H. - Page 7 PT-FX400 LCD Projector Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 4:3 minimum L (m) = (diagonal screen size in inches) × 0.0305 – 0.049 maximum L (m) = (diagonal screen size in inches) ×...
-
Page 8: List Of Compatible Signals
PT-FX400 LCD Projector List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning fre- quencies of 15.6 kHz to 91.1 kHz, vertical scanning frequencies of 24.0 Hz to 85.1 Hz, and a dot clock of 162 MHz maximum can be input. - Page 9 PT-FX400 LCD Projector Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, com- mands must be input through communication software, based on the format and satisfying the commu- nication conditions shown below. Pin assignments and signal names...
-
Page 10: Cable Specifications
PT-FX400 LCD Projector Cable specifications Projector PC (DTE) Control commands Command: <Parameter> Function Callback: <Parameter> Parameter value Power on (standby mode on) PO N – – Power off (standby mode off) – – Volume control AVL:<pl> AVL:<pl> Input signal selection IIS:<input signal>... -
Page 11: Status Request Commands
PT-FX400 LCD Projector Status request commands Command Description Callback <Parameter> <power condition> Standby power status <lamp condition> Lamp status Input signal status <input signal> Volume adjustment value <pl> Color adjustment value <pl> <pl> Tint adjustent value <pl> Brightness adjustment value <pl>... -
Page 12: Parameter Format
PT-FX400 LCD Projector Parameter format Parameter format Size (Byte) Definition <pl> 3 (1 or 2 bytes also Decimal without signs: 0 –999 (000, 001, 002...999) possible when Decimal with signs: -99 to +99 (-99...-01, +00, +01, +02...+99) under control) Callback from the projector is 3 Byte. - Page 13 PT-FX400 LCD Projector Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. Never place objects on top of the projector while it is operating. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s exhaust openings.