Panasonic TH-85PF12U Operating Instructions Manual page 56

Options Adjustments
Item
Off
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 15).
• Signal can be displayed when the Terminal board is installed.
INPUT lock
• Input switch can be used when this is set to "Off".
• In two screen display mode, if anything other than "Off" is set, the value will be fi xed as the value input in
the single screen display mode.
• When a dual input terminal board is attached, A or B is displayed depending on the selected input signal.
(Ex. INPUT1A, INPUT1B)
Off
Off: All the buttons on main unit can be used.
MENU&ENTER:
On: Locks all the button on bottom face of main unit.
Button lock
Sets Button lock with the unit buttons in the following procedure.
Off: Press
MENU&ENTER: Press
On: Press
Off
Off:
User1: You can only use
Remocon User level
User2: You can only use
User3: Locks all the buttons on remote control.
Enable:
Disable: Disables the "Off-timer function".
Off-timer function
Note: When "Disable" is set, the Off-timer is cancelled.
Normal
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Normal: Power returns in as the same state as before the power interruption.
Initial Power Mode
Standby: Power returns in standby mode. (Power Indicator : red/orange)
On:
Note: When using multiple displays, "Standby" is preferred to be set in order to reduce a power load.
Sets panel ID number when panel is used in "Remote ID" or "Serial ID".
Set value range: 0 - 100
ID select
(Standard value: 0)
The setting of this menu is valid only when using ID remote control.
Off:
On:
Remote ID
Note: To use the ID remote control function, it is necessary to set each ID number of remote control and
Sets the panel ID Control.
Off:
Serial ID
On:
Adjusts the image display size on screen.
Off:
On:
Notes:
Display size
• This setting is valid only when the input signals are as follows;
NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (BNC Dual Video Terminal Board (TY-FB9BD))
525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p,
1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when two screen display, digital zoom, Multi display or Portrait display is selected.
• When "Display size" is set to "On", "H-POS" and "V-POS" in "POS. /SIZE" can be adjusted.
• Refer to each board's operating instruction for DVI, SDI, HDMI's corresponding signals.
56
PC INPUT1 INPUT2
MENU&ENTER On
Locks and buttons on right side of main unit.
MENU MENU ENTER/ ENTER/
four times→Press
+
/
four times→Press
ENTER/ ENTER/
four times→Press
-
/
User1 User2
You can use all of the buttons on the remote control.
, ,
, , buttons on the remote control.
Enables the "Off-timer function".
Standby On
Power returns in power On. (Power Indicator : green)
Disables ID remote control functions. You can use normal remote control operations.
Enable ID remote control functions.
display unit. About the setting method, please refer to "ID Remote Control Function" (see page 46)
and "ID select" (above-mentioned).
Disables external control by the ID.
Enables the external control by the ID.
Sets the normal image display size on screen.
Sets the image display size approximately 95 % of the normal image display.
Off
Adjustments
INPUT3
four times→Press
INPUT
four times→Press
+
/
four times→Press
ENTER/ ENTER/
User3
, , , ,
On
four times→Press
-
/ ENTER/ ENTER/
four times→Press
INPUT
four times→Press
+
/ ENTER/ ENTER/
, buttons on the remote control.
ENTER/ ENTER/