Panasonic TH-42LFE6E Operating Instructions Manual page 43

Item
Locks the input switch operation.
Off
Notes:
Input lock
• Only the adjusted signal is displayed (see page 15).
• Input switch can be used when this is set to "Off".
Off
Off: All the buttons on main unit can be used.
MENU&ENTER: Locks
On: Locks all the button on main unit except the Power switch.
Button lock Sets Button lock with the unit buttons in the following procedure.
Off: Press
MENU&ENTER: Press
On: Press
Off
Off:
User1: You can only use
Remocon User level
User2: You can only use
User3: Locks all the buttons on remote control.
Enable:
Disable: Disables the "Off-timer function".
Off-timer function
Note:
Normal
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Normal: Power returns in as the same state as before the power interruption.
Initial Power Mode
Standby: Power returns in standby mode. (Power Indicator : red/orange)
On:
Note: When using multiple displays, "Standby" is preferred to be set in order to reduce a power load.
Sets panel ID number when panel is used in "Remote ID" or "Serial ID".
Set value range: 0 - 100
ID select
(Standard value: 0)
The setting of this menu is valid only when using ID remote control.
Off:
On:
Remote ID
Note: To use the ID remote control function, it is necessary to set each ID number of remote control and
Sets the panel ID Control.
Serial ID Off:
On:
Off:
Studio W/B On:
Note: Valid only when the "Warm" is set as "White balance" in Picture menu.
Off
You can set the power-on delay time of the displays to reduce the power load, when you press
turn on the multiple displays that are set together, for example, on MULTI DISPLAY system.
Set each display's setting individually.
Power ON Screen Off:
1 to 30 (sec.): Set the power-on delay time (second).
Delay
Notes:
• During this function is working, the power indicator is blinking green.
• This function also works when the power recovers from failure or after plugging off and in again the power cord.
Whether to show/hide No activity power off Precautions at the time of power ON is set.
Power On Message On:
(No activity power Off:
off) Note:
This setting is enabled only if "No activity power off" is "Enable" (see page 30).
Off:
On:
The clock is displayed at the lower left of the screen when
Clock Display
PC DVI HDMI
On MENU&ENTER
MENU ENTER/
and
four times→Press
ENTER/
four times→Press
four times→Press
User1 User2
You can use all of the buttons on the remote control.
, ,
button on the remote control.
Enables the "Off-timer function".
When "Disable" is set, the Off-timer is cancelled.
On Standby
Power returns in power On. (Power Indicator : green)
Disables ID remote control functions. You can use normal remote control operations.
Enable ID remote control functions.
display unit. About the setting method, please refer to "ID Remote Control Function" (see page
35) and "ID select" (above-mentioned).
Disables external control by the ID.
Enables the external control by the ID.
Nullify all the settings adjusted.
Sets the colour temperature for TV studio.
1 2 3.... 30
The display will be turned on at the same time as
After pressing , the display will be powered on with time delay depending on this setting.
The warning precautions are shown at the time of power ON.
The warning precautions are not shown at the time of power ON.
Not display the clock.
Display the clock.
Note: When "PRESENT TIME Setup" is not set, the clock is not displayed even
if "Clock Display" is "On". (see page 26)
10:00
Adjustments
Off
buttons on main unit.
INPUT
four times→Press four times→Press
four times→Press
ENTER/
four times→Press four times→Press
User3
, , buttons on the remote control.
Options Adjustments
ENTER/
INPUT
four times→Press
ENTER/
is pressed.
button is pressed.
ENTER/
to
43 43