Download Print this page

GE 16179610 User Manual

40-channel 900mhz cordless call waiting caller id telephone with universal voice mail indicator (uvmi).
Hide thumbs
   

Advertisement

26900
I
NTRODUCTION
40-Channel 900MHz Cordless Call
THE LIGHTNING
FLASH AND ARROW
WARNING: TO
Waiting Caller ID Telephone with
HEAD WITHIN THE
PREVENT FIRE OR
TRIANGLE IS A
WARNING SIGN
Universal Voice Mail Indicator (UVMI)
ELECTRICAL SHOCK
ALERTING YOU OF
HAZARD, DO NOT
"DANGEROUS
User's Guide
EXPOSE THIS
VOLTAGE" INSIDE
THE PRODUCT.
PRODUCT TO RAIN
OR MOISTURE.
CAUTION: When using telephone equipment, there are basic safety
instructions that should always be followed. Refer to the IMPORTANT
SAFETY INSTRUCTIONS provided with this product and save them for
future reference.
Congratulations on purchasing this Call Waiting Caller ID phone system with UVMI.
This phone has been designed to be simple to use, however, you can reach its full
______
CID/VOL.
_
<
+
>
potential more quickly by taking a few minutes to read this User's Guide.
TALK
CALL BACK
This system is a multifunction product for use with the Call Waiting Caller ID and
Universal Voice Mail (UVMI) services available from your local telephone company.
1
ABC
2
DEF
3
To use all of the features of this system, you must subscribe to the following services
5
GHI
4
JKL
MNO
6
available from your local telephone company:
7
8
9
PQRS
TUV
WXYZ
• the standard name/number Caller ID service to identify and screen callers when
CANCEL
OPER
0
#
TONE
*
PAGE
PAUSE
the phone rings or know who called while you were away
MEMORY
RINGER
• Call Waiting Caller ID service to view the name and telephone number of an
OFF
ON
incoming call while you are on the phone
• Universal Voice Mail Indicator (UVMI) to receive voice mail messages
charge/in use
The system allows you to:
• view the name and number of each incoming call
• view the time and date of each call
• eliminate harassment from annoying calls, or get prepared before answering a call
• record up to 40 Caller ID messages sequentially
IMPORTANT: Because cordless phones operate on electricity, you should have
at least one phone in your home that isn't cordless, in case the power in your
E
A
I
QUIPMENT
PPROVAL
NFORMATION
home goes out.
Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in
compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone
B
Y
B
EFORE
OU
EGIN
Terminal Equipment published by ACTA.
1 Notification to the Local Telephone Company
P
C
ARTS
HECKLIST
On the bottom of this equipment is a label indicating, among other information, the US number and Ringer
Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your
Make sure your package includes the items shown here.
telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line and still
have all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of
the RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you
may connect to your line as determined by the REN, you should contact your local telephone company.
+
cid/vol
_
CALL BACK
TALK
2
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply
PAGE
1
ABC
3
DEF
GHI
4
JKL
5
6
MNO
PQRS
7
8
TUV
9
WXYZ
with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord
cancel
0
TONE
*
OPER
PAUSE
#
and modular plug is provided with this product. It is designed to be connected to a compatible modular jack
charge/in use
delete
chan
mem
ringer
flash
program
off
on
that is also compliant. See installation instructions for details.
Notes
Base
Handset
Belt clip
This equipment may not be used on coin service provided by the telephone company.
Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone
equipment if you are on a party line. Check with your local telephone company.
T
J
R
ELEPHONE
ACK
Notice must be given to the telephone company upon permanent disconnection of your telephone from
your line.
To use this phone, you need an RJ11C type modular telephone
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation
jack, which might look like the one pictured here, installed in
of this product does not disable your alarm equipment. If you have questions about what will disable
alarm equipment, consult your telephone company or a qualified installer.
your home. If you don't have a modular jack, call your local
phone company to find out how to get one installed.
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone
company shall, where practicable, notify you that temporary discontinuance of service may be required. Where
prior notice is not practicable and the circumstances warrant such action, the telephone company may
INSTALLATION NOTE: Some cordless telephones operate at frequencies that
temporarily discontinue service immediately. In case of such temporary discontinuance, the telephone company
may cause interference to nearby TVs, microwave ovens, and VCRs. To minimize
must: (1) promptly notify you of such temporary discontinuance; (2) afford you the opportunity to correct the
situation; and (3) inform you of your right to bring a complaint to the Commission pursuant to procedures set
or prevent such interference, the base of the cordless telephone should not be
forth in Subpart E of Part 68, FCC Rules and Regulations.
placed near or on top of a TV, microwave ovens, or VCR. If such interference
The telephone company may make changes in its communications facilities, equipment, operations or procedures
where such action is required in the operation of its business and not inconsistent with FCC Rules and
continues, move the cordless telephone farther away from these appliances.
Regulations. If these changes are expected to affect the use or performance of your telephone equipment, the
telephone company must give you adequate notice, in writing, to allow you to maintain uninterrupted service.
D
S
S
IGITAL
ECURITY
YSTEM
H
A
C
Your cordless phone uses a digital security system to provide protection against false
EARING
ID
OMPATIBILITY
ringing, unauthorized access, and charges to your phone line.
This telephone system meets FCC standards for Hearing Aid Compatibility.
When you place the handset in the base, the unit verifies its security code. After a
US NUMBER IS LOCATED ON THE CABINET BOTTOM
power outage or battery replacement, you should place the handset in the base for
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
about 20 seconds to reset the code.
Model 26900A
16179610 (Rev. 2 DOM E)
03-43
Printed in China
I
I
I
MPORTANT
NSTALLATION
NFORMATION
• Never install telephone wiring during a lightning storm.
CAUTION:
RISK OF ELECTRIC SHOCK
• Never install telephone jacks in wet locations unless the jack is specifically
DO NOT OPEN
designed for wet locations.
CAUTION: TO REDUCE THE
THE EXCLAMATION
RISK OF ELECTRIC SHOCK, DO
POINT WITHIN THE
• Never touch uninsulated telephone wires or terminals, unless
NOT REMOVE COVER (OR
TRIANGLE IS A
BACK). NO USER
WARNING SIGN
the telephone line has been disconnected at the network
SERVICEABLE PARTS INSIDE.
ALERTING YOU OF
interface.
REFER SERVICING TO
IMPORTANT
QUALIFIED SERVICE
INSTRUCTIONS
• Use caution when installing or modifying telephone lines.
ACCOMPANYING
PERSONNEL.
THE PRODUCT.
• Temporarily disconnect any equipment connected to the
SEE MARKING ON BOTTOM / BACK OF PRODUCT
phone such as faxes, other phones, or modems.
I
B
NSTALLING THE
ATTERY
1. Remove the battery compartment door on the handset.
Battery
2. Insert the battery pack, and connect the cord into the
jack
jack inside the compartment.
3. Put the battery compartment door back on and set the
handset aside.
I
P
NSTALLING THE
HONE
Your telephone should be placed on a level surface such as a desk or table top, or
you can mount it on a wall. A wall mounting pedestal is packaged with your phone.
NOTE: For desktop charging only, the handset may be charged facing up.
C
T
L
ONNECTING THE
ELEPHONE
INE
• Plug the one end of the telephone line cord into the jack marked TEL LINE on the
back of the base and the other end into a modular wall phone jack.
• Set the RINGER switch (on the handset) to ON, and place the handset in the cradle
on the base.
NOTE: The phone is shipped from the manufacturer in tone dialing mode.
C
AC (E
) P
ONNECTING THE
LECTRICAL
OWER
Handset battery
• Plug the power supply cord into the power jack on the back of the base and the
other end into an electrical outlet. The IN USE/CHARGE/V-MAIL indicator turns on
to indicate the battery is charging when the handset is placed on the base cradle.
• Place the handset in the cradle on the base.
Wall mounting
AC power
Telephone
Allow the phone to charge for 12 hours prior to first use. If you don't properly charge
pedestal
supply
line cord
the phone, battery performance is compromised.
CAUTION: Use only the ATLINKS USA, Inc. 5-2558 (white) power supply
EQUIREMENTS
Wall plate
that came with this unit. Using other power supplies may damage the unit.
W
M
Modular
ALL
OUNTING
telephone
line jack
NOTE: For best results, before you hang the phone on the wall, charge the
phone on a flat surface.
1. Turn the base over.
R
2. Attach the wall mounting pedestal by first inserting the tabs on the open edge of
1. Check the display to see who is calling.
the pedestal into the slots on the lower portion of the bottom of the base. Then
push down and snap the pedestal into place.
2. Press the TALK/CALLBACK button.
3. Slip the mounting holes (on the back of the base and pedestal) over the wall plate
posts and slide the unit down into place. (Wall plate not included.)
M
NOTE: If desired, gather the extra telephone line and power supply cord
To make a call, press the TALK/CALLBACK button before you dial and press it again to
together, fasten with a wire tie, and store inside the wall mounting pedestal.
hang up. Or you may dial a number, and then press the TALK/CALLBACK button.
S
U
ET
P
R
There are five programmable menus available: Language, Area Code, Ringer Tone,
While the phone is on, press the REDIAL button to quickly redial the last number you
Tone/Pulse Dialing, and Default Setting. Set up should be done when the phone is
dialed (up to 32 digits). If you get a busy signal, and want to keep dialing the number,
OFF (not in TALK mode).
just press REDIAL again (you don't have to turn the phone off and back on). Or you
may press the REDIAL button, and then press the TALK/CALLBACK button.
L
S
S
ANGUAGE
ETTING
ELECTION
F
1. Press the FLASH/PROGRAM button until 1ENG 2FRA 3ESP shows in the display.
1ENG is the default setting.
If you subscribe to the combined Call Waiting Caller ID service from your local telephone
2. Use the CID/VOL (< or >) button or the touch-tone pad to move the arrow to your
company, you will receive Caller ID information (if available) on Call Waiting calls. During
Battery plug
selection.
a phone call, you will hear a beep to indicate another call is waiting on the line and Caller
ID information for the waiting call shows on the handset display. To connect to the
3. Press FLASH/PROGRAM to store selection.
waiting call, press the flash button on the handset and your original call is put on hold.
You may switch back and forth between the two calls by pressing the flash button.
A
C
S
REA
ODE
ELECTION
1. Press the FLASH/PROGRAM button until AREA CODE - - - shows in the display. - - - is
the default setting.
2. Use the touch-tone pad on the handset to enter your three digit area code.
I
NOTE: If you make a mistake, press the CHANNEL/DELETE button to erase
the wrong area code and repeat step 2.
The IN USE/CHARGE/V-MAIL indicator is lit when the handset is charging in the
3. Press FLASH/PROGRAM to store selection.
cradle on the base or when the phone is ON. It flashes when you receive an
R
T
S
incoming call or when the PAGE button is pressed.
INGER
ONE
ELECTION
1. Press the FLASH/PROGRAM button until RINGER TONE shows in the display. 1 is the
V
default setting.
Provided your phone company offers voice messaging service (voice mail) and you
2. Use the CID/VOL (< or >) button or the touch-tone pad to move the arrow to
have subscribed to it, the IN USE/CHARGE/V-MAIL indicator on the base flashes
1, 2, or 3.
when the phone is not in use to indicate there is a message waiting. The indicator
stops flashing when the message is reviewed.
3. Press FLASH/PROGRAM to store selection.
T
/P
D
S
C
ONE
ULSE
IALING
ELECTION
1. Press the FLASH/PROGRAM button until 1TONE 2PULSE shows in the display.
While talking, you might need to manually change the channel in order to get rid of static.
1TONE is the default setting.
Press and release the CHANNEL/DELETE button to advance to the next clear channel.
2. Use the CID/VOL (< or >) button or the touch-tone pad to move the arrow to 1TONE
T
or 2PULSE .
3. Press FLASH/PROGRAM to store selection.
This feature is useful only if you have pulse dialing service. Temporary Tone Dialing
enables pulse (rotary) service phone users to access touch-tone services offered by
D
S
S
EFAULT
ETTING
ELECTION
banks, credit card companies, etc. For example, when you call your bank you may
need to enter your bank account number. Temporarily switching to Touch Tone mode
1. Press the FLASH/PROGRAM button until DEFAULT shows in the display. 1 NO is
allows you to send your number.
the default setting.
1. Dial the telephone number and wait for the line to connect.
2. Use the CID/VOL (< or >) button or the touch-tone pad to move the arrow to 1 NO
or 2 YES .
2. When your call is answered, press the TONE*/CANCEL button on the handset
3. Press FLASH/PROGRAM to store selection. You will hear a confirmation tone.
3. Follow the automated instructions to get the information you need.
C
P
B
ORDLESS
HONE
ASICS
4. Hang up the handset and the phone automatically returns to PULSE (rotary)
Display
C
CID/VOL (< or >) buttons
Press the TONE*/CANCEL button to cancel any command you initiated.
TALK/CALL
BACK button
F
______
CID/VOL.
+
_
<
>
This feature helps to locate a misplaced handset.
TALK
CALL BACK
REDIAL button
FORMAT button
Press the PAGE button on the base. The handset beeps continuously for about 2
2
minutes or until you press the TALK/CALLBACK on the handset or the page button on
1
ABC
DEF
3
the base.
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
CANCEL
TONE */CANCEL
OPER
0
#
PAUSE # button
TONE
*
PAUSE
button
MEMORY
RINGER
R
OFF
ON
FLASH/PROGRAM
CHANNEL/DELETE
button
The RINGER switch must be ON for the handset to ring during incoming calls.
button
MEMORY button
RINGER switch
C
V
ECEIVING A
ALL
OLUME
While the phone is ON, use the CID/VOL (< or >) button to adjust the receiver volume.
Press the > button to increase the volume and the < button to decrease the volume.
C
ID F
ALLER
EATURES
C
AKING A
ALL
Time
EDIAL
Caller ID phone number
LASH
Caller ID (CID) is a service available from your local telephone company. For Caller ID
to work on this system, you must subscribe to Caller ID service. To receive Caller ID
information for a Call Waiting call, you must subscribe to the combined Call Waiting
Caller ID service.
When your telephone rings, and you are subscribed to Call Waiting Caller ID service,
you will receive information (if available) transmitted by your local telephone
company. You will also receive Caller ID information from Call Waiting calls.
TIP: Don't use the TALK/CALLBACK button to activate custom calling services
If you receive an incoming call and you are already on the phone, a beep indicates
such as call waiting, or you'll hang up the phone.
the presence of a Call Waiting Call on the line, and Caller ID information for the Call
Waiting call shows on the display. This information may include the phone number,
U
/C
/V-M
I
date and time; or the name, phone number, and date and time. The unit stores up to
N
SE
HARGE
AIL
NDICATOR
40 calls for later review.
• Press the PROGRAM/FLASH button to put the current call on hold so you can
answer the incoming call.
R
S
ECEIVING AND
TORING
M
OICE
ESSAGING
When you receive a call, the information is transmitted by the phone company to
your Caller ID telephone between the first and second ring.
When the memory is full, a new call automatically replaces the oldest call in
memory. NEW appears in the display for calls received that have not been reviewed.
REPT indicates that a new call from the same number was received more than once.
NOTE: Check with your local phone company regarding name service availability.
B
HANNEL
UTTON
R
R
EVIEWING
ECORDS
T
As calls are received and stored while the phone is OFF (not in TALK mode), the
EMPORARY
ONE
display is updated to let you know how many calls have been received.
• Press the CID/VOL < button to scroll through the call records from the most recent
to the oldest.
• Press the CID/VOL > button to scroll through the call records from the oldest to
the newest.
T
CID R
RANSFERRING
number pad to temporarily change from PULSE dialing to TONE dialing.
You may transfer a Caller ID record to your phone's memory.
NOTE: It is important that you format CID records correctly before storing in
memory. It is not possible to re-format CID records stored in memory.
dialing mode.
1. Make sure the phone is OFF (not in TALK mode).
ANCEL
2. Use the CID/VOL (< or >) button to scroll to the desired record.
3. Press the MEMORY button.
4. Press the desired memory location. Example, press the number 1 key to store the
H
record in memory location 1. You will hear a confirmation tone.
INDING THE
ANDSET
To Replace an Old Memory with a New CID Record:
1. Repeat steps 1 through step 4 in Transferring CID Records To Memory.
2. After entering the memory location, REPLACE MEMO? shows in the display.
3. Press the MEMORY button again, and the new CID record replaces the old memory
NOTE: The ringer does not have to be on for this feature to work.
in that location. You will hear a confirmation tone.
D
R
ELETING
ECORDS
S
INGER
WITCH
Use the CHANNEL/DELETE button to erase the record currently shown in the display
or all records.
D
C
R
ELETING THE
URRENT
ECORD
1. Make sure the phone is OFF (not in TALK mode).
2. Use the CID/VOL (< or >) buttons to display the desired Caller ID record.
3. Press CHANNEL/DELETE. The display shows DELETE CALL ID?
4. Press CHANNEL/DELETE again to erase the record and the next Caller ID record
shows in the display. You will hear a confirmation tone.
Date
Number of calls
D
A
R
ELETING
LL
ECORDS
1. Make sure the phone is OFF (not in TALK mode).
2. Use the CID/VOL (< or >) buttons to display any Caller ID record.
3. Press and hold CHANNEL/DELETE button until DELETE ALL? shows in the display.
4. Press CHANNEL/DELETE again to erase all records. You will hear a confirmation
tone. The display shows NO CALLS .
Caller ID name
D
C
ID N
IALING A
ALLER
UMBER
1. Make sure the phone is OFF (not in TALK mode).
2. Use the CID/VOL (< or >) buttons to display the desired Caller ID record.
3. Press TALK/CALLBACK. The number dials automatically.
C
CID N
F
HANGING THE
UMBER
ORMAT
The FORMAT button lets you change the format of the displayed CID number. The
available formats are as follows.
7-digit
7-digit telephone number.
10-digit
3-digit area code + 7-digit telephone number.
11-digit
long distance code "1" + 3-digit area code + 7-digit telephone number.
1. Make sure the phone is OFF (not in TALK mode).
C
2. Use the CID/VOL (< or >) buttons to scroll to the number you want to call back.
ALLS
3. If the CID format does not appear as desired, press the FORMAT button. Repeat if
necessary, until the correct number of digits are shown.
4. Press TALK/CALLBACK. The number dials automatically.
M
EMORY
Store up to ten 24-digit numbers in memory for quick dialing. This memory feature is
in addition to the 40 Caller ID records that can be stored in the Caller ID memory log.
S
N
N
M
TORING A
AME AND
UMBER IN
EMORY
1. Make sure the phone is OFF (not in TALK mode).
2. Press the MEMORY button.
3. Press the desired memory location (0 through 9).
4. Press the MEMORY button again. The display shows ENTER NAME .
NOTE: If you don't want to enter the name, skip step 5.
5. Use the touch-tone pad on the handset to enter the name (up to 15 characters) and
M
ECORDS TO
EMORY
press the memory button to save. More than one letter is stored in each of the
number keys. For example, to enter the name Bill Smith, press the 2 key twice for the
letter B. Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter L.
Wait for 1 second, and then press the 5 key 3 times for the second letter L. Press the 1
key to insert a space between the L and the S. Press the 7 key 4 times for the letter S;
press the 6 key once for the letter M; press the 4 key 3 times for the letter I; press the 8
key for the letter T; press the 4 key twice for the letter H.
NOTE: The cursor will automatically move to the next position if another
number key is pressed.
6. Press the MEMORY button to save the name. The display shows ENTER NUMBR .
7. Use the touch-tone pad to enter the telephone number you want to store (up to
24 digits).
8. Press MEMORY again to store the number. You will hear a confirmation tone.
C
S
N
HANGING A
TORED
UMBER
1. Repeat steps 1 through 7 in Storing a Name and Number in Memory.
2. Press the MEMORY button, and " REPLACE MEMO? " shows in the display.
3. Press the MEMORY button to store the number. You will hear a confirmation tone.

Advertisement

   Related Manuals for GE 16179610

   Summary of Contents for GE 16179610

  • Page 1

    (3) inform you of your right to bring a complaint to the Commission pursuant to procedures set or prevent such interference, the base of the cordless telephone should not be forth in Subpart E of Part 68, FCC Rules and Regulations.

  • Page 2

    TORING A EDIAL UMBER EADSET AND PERATION 1. Repeat steps 1 through 6 in Storing a Name and Number in Memory. 2. Press the REDIAL button. ONNECTING AN PTIONAL Headset jack 3. Press the MEMORY button to store the number. You will hear a confirmation tone. EADSET TO THE ANDSET To Replace an Old Memory with a New Redial Number:...

This manual also for:

26900, 26900a

Comments to this Manuals

Symbols: 0
Latest comments: