Download Print this page

Advertisement

DCN multimedia
Conference System
en
Hardware Installation Manual

Advertisement

   Also See for Bosch DCN multimedia

   Summary of Contents for Bosch DCN multimedia

  • Page 1

    DCN multimedia Conference System Hardware Installation Manual...

  • Page 3: Table Of Contents

    Mechanical installation of Central Equipment DCNM-APS and DCNM-PS Mechanical installation of Contribution Devices DCNM-MMD Multimedia Device DCNM-HDMIC High Directive Microphone DCNM-MMDSP Anti-reflection foil DCNM-NCH Name Card Holder Installation Test Bosch Security Systems B.V. Hardware Installation Manual 2013-08 | V1.0 |...

  • Page 4: Safety

    These instructions are supplied together with all equipment that can be connected to the mains supply. Safety precautions Some products of the DCN multimedia product range are designed to be connected to the public mains network. To avoid any risk of electric shock, all interventions must be carried out with disconnected mains supply.

  • Page 5: About This Manual

    (PDF). For more information, refer to the product related information on www.boschsecurity.com Intended audience This hardware installation manual is intended for installers of a DCN multimedia conference system. Alerts and notice signs Four types of signs can be used in this manual. The type is closely related to the effect that may be caused if it is not observed.

  • Page 6: System Installation Overview

    It is advisable to participate in the DCN multimedia conference system training before you install, prepare, configure and operate a DCN multimedia system. The DCN multimedia system is an IP based conference system which runs on an OMNEO compatible Ethernet network. It is used for distributing and processing audio, video and data signals.

  • Page 7: Typical System Setup

    – 5.2 is a DCNM‑MMD used via “Power over Ethernet” (PoE) Ethernet switch. System Network Cable (DCNM‑CBxxx): – Connects DCN multimedia devices, audio powering switch and powering switch with each other. Ethernet switch: – Ethernet switch with PoE on some ports. Routes the system data via Ethernet.

  • Page 8: System Installation Design And Planning

    Notice! Make sure that the cable lengths and power consumptions do not exceed the specifications: Not doing so will result in malfunctioning at any moment of the DCN multimedia products and system. System capabilities DCN multimedia product and system capabilities depend on: –...

  • Page 9

    Power supply capacity The total system network cable length and connected devices determine the required power supply capacity. The power within the DCN multimedia conference system is supplied by: – The Audio Powering Switch (DCNM‑APS) and the Powering Switch (DCNM‑PS), or –...

  • Page 10: Hardware Requirements

    The price range for these switches varies depending on the number of ports the switch may have. More expensive switches are also available, but have not been taken into consideration. 2013-08 | V1.0 | Hardware Installation Manual Bosch Security Systems B.V.

  • Page 11

    Remarks Cisco 3560‑X series Requires IP services feature set HP 3500 yl series Requires Premium License HP 3800 series HP 4800 series HP 5500‑EI series Netgear GSM7328S‑200 Netgear GSM7352S‑200 Bosch Security Systems B.V. Hardware Installation Manual 2013-08 | V1.0 |...

  • Page 12: Power Supply Capacity Calculation Plan

    DCNM‑CB05 2.43 DCNM‑CB10 4.50 DCNM‑CB25 10.71 Table 4.1: Power consumption (Watts) Ordering number Cable lengths DCNM-CB02 6.56 DCNM-CB05 16.40 DCNM-CB10 32.81 DCNM-CB25 82.02 Table 4.2: Cable types and lenghts 2013-08 | V1.0 | Hardware Installation Manual Bosch Security Systems B.V.

  • Page 13

    Socket 3, 4, 5 high power. 14, 16, 18, 20 Overload LED for sockets 2‑5: Green: Power OK. Red: Overload. Remove cable and wait a few seconds for the system to reset the overload. Bosch Security Systems B.V. Hardware Installation Manual 2013-08 | V1.0 |...

  • Page 14

    (3, 4, or 5). Figure 4.4: Example DCNM‑MMD with DCNM‑APS redundant cabling DCNM‑APS. DCNM‑MMD. CAT‑5e cable. System network cable for redundant cabling. System network cable for daisy‑chain cabling. 2013-08 | V1.0 | Hardware Installation Manual Bosch Security Systems B.V.

  • Page 15: Calculation Using Poe Switches

    If the PoE is used, the DCNM‑MMD cannot be configured as a daisy‑chain; redundant cabling is not required. Using PoE, the DCNM‑MMD cannot be daisy‑chained connected. Using PoE does not provide redundant cabling. Item Description Network connector Network/PoE connector Bosch Security Systems B.V. Hardware Installation Manual 2013-08 | V1.0 |...

  • Page 16: Installation Material And Tools

    The system network cables, terminated with connectors on both ends, are available in different lengths and are used to connect DCN multimedia devices to each other. The cable consists of four CAT‑5e twisted pairs to transmit data and two copper wires to supply the power.

  • Page 17: Dcnm-cbcon System Network Cable Connector (50 Pcs)

    Figure 5.2: DCNM-CBCON Front and exploded view Item Description Strain relief boot Ferrule Plug connector shield Power contacts (Qty: 2) Load bar Power contact cavity (2 places) Housing Locking latch Signal contact cavity (8 Places) Bosch Security Systems B.V. Hardware Installation Manual 2013-08 | V1.0 |...

  • Page 18: Dcnm-cbtk System Network Cable Toolkit

    Power wiring tool. Signal wiring tool. Table 5.2: Toolkit content Notice! Please consult the “custom length for system network cables” section on the DVD, which is supplied with the DCNM‑APS. 2013-08 | V1.0 | Hardware Installation Manual Bosch Security Systems B.V.

  • Page 19: Dcnm-cb250 System Installation Cable

    Please consult the “custom length for system network cables” section on the DVD, which is supplied with the DCNM‑APS. See also – DCNM-CBCON System Network Cable Connector (50 pcs), page 17 – DCNM-CBTK System Network Cable Toolkit, page 18 Bosch Security Systems B.V. Hardware Installation Manual 2013-08 | V1.0 |...

  • Page 20: Mechanical Installation Of Central Equipment

    Ventilation inlet. Indication LED: Off: Switched off. Green: Switched on. Amber: Standby. Blinking: Services on the server PC are not running. Alternating green amber: When a software download is required. 2013-08 | V1.0 | Hardware Installation Manual Bosch Security Systems B.V.

  • Page 21

    Socket 3, 4, 5 high power. 14, 16, 18, 20 Overload LED for sockets 2‑5: Green: Power OK. Red: Overload. Remove cable and wait a few seconds for the system to reset the overload. Bosch Security Systems B.V. Hardware Installation Manual 2013-08 | V1.0 |...

  • Page 22

    The device extends 30 mm in front of the 19” mounting brackets when installed in a 19” rack system. Caution! Do not obstruct the airflow vents on the front side and rear left and right sides. 2013-08 | V1.0 | Hardware Installation Manual Bosch Security Systems B.V.

  • Page 23: Mechanical Installation Of Contribution Devices

    Two‑way loudspeaker. 3.5 mm stereo jack for headphone or headset with integrated microphone. Headphone volume control. Chairperson priority or microphone mute button. Microphone request button. Cable guides. Microphone input connector. Bosch Security Systems B.V. Hardware Installation Manual 2013-08 | V1.0 |...

  • Page 24

    Figure 7.2: DCNM-MMD Bottom view (fixed installation) Item Description Screw insert for fixed installation. 2x RJ45 connection input/output for system power cable. Cable guides. USB connector (for future use) 2013-08 | V1.0 | Hardware Installation Manual Bosch Security Systems B.V.

  • Page 25

    DCN multimedia Mechanical installation of Contribution Devices | en See also – DCNM-CBxx System Network Cable, page 16 – DCNM-CB250 System Installation Cable, page 19 Bosch Security Systems B.V. Hardware Installation Manual 2013-08 | V1.0 |...

  • Page 26: Dcnm-hdmic High Directive Microphone

    Description LED indicator. Microphone grill (left and right). Microphone grill (front and rear). Connection guidance. Slider guidance. Connector plug. Lockslider for lock release (Press and shift to release). Lock. 2013-08 | V1.0 | Hardware Installation Manual Bosch Security Systems B.V.

  • Page 27: Dcnm-mmdsp Anti-reflection Foil

    To remove the microphone from the DCNM‑MMD: Shift lockslider (7) towards the DCNM‑MMD and hold in place lock release (8) and pull out the microphone. DCNM-MMDSP Anti-reflection foil The DCN multimedia Anti‑reflection foil is a self‑absorbed premium tempered glass screen protector which has anti‑scratch and anti‑wear features. Installation procedure Please use the included alcohol swab and the microfiber fabric to clean the DCNM‑MMD...

  • Page 28: Dcnm-nch Name Card Holder

    DCNM‑MMD. Figure 7.5: DCNM‑NCH to DCNM‑MMD assembly Item Description Name card holder. Magnets. Notice! A paper insert template is included on the DVD that is supplied with the DCNM‑APS. 2013-08 | V1.0 | Hardware Installation Manual Bosch Security Systems B.V.

  • Page 29: Installation Test

    Not to do so could result in a system malfunctioning. Each DCN multimedia device (DCNM‑MMD) has its own build‑in diagnostics, which can be used for faultfinding. The diagnostics starts as soon the device is powered on. The DCN multimedia conference system does not have to be configured with, and connected to, the system controller PC.

  • Page 30

    Customer service If a fault cannot be resolved, please contact your supplier or system integrator, or go directly to your Bosch representative. 2013-08 | V1.0 | Hardware Installation Manual Bosch Security Systems B.V.

  • Page 32

    Bosch Security Systems B.V. Torenallee 49 5617 BA Eindhoven The Netherlands www.boschsecurity.com © Bosch Security Systems B.V., 2013...

Comments to this Manuals

Symbols: 0
Latest comments: