Advertisement
RS232 Software specification
1.Each input character will be echoed.
2.If the command format is illegal, it will echo "Illegal format＂.
3.If the command format is correct, it will action and return ACK.
4.If the command format is correct, but it is not valid for this model, it will echo "Unsupported item＂.
5.If the command format is correct, but can't be execute in some condition, it will echo "Block item＂.
6.Press Enter right after ">" wouldn't get any echo
7.Press Space after ">" then Enter would echo"Illegal format＂
Notice XD95U can detect the capital letter and the small letter for input character, but ACK is only the capital letter.
CMD
ACTION
Power On
Power
Power off
Power Status
VGA/YPbPr
Source Selection
Composite
SVIDEO
Current source
Contrast +
Contrast -
Contrast value
Brightness +
Brightness -
Picture Setting
Brightness value
Aspect 4:3
Aspect 16:9
Aspect Auto
Aspect Real
Lamp 1 Hour
Normal mode
Lamp Control
Economic mode
LampMode Status
Blank On
Blank Off
Blank Status
Freeze On
Freeze Off
Freeze Status
Menu On
Miscellaneous
Up
Down
Right
Left
enter
Auto
Zoom In
Zoom out
ASCII
<CR>*pow=on#<CR>
<CR>*POW=ON#<CR>
<CR>*pow=off#<CR>
<CR>*POW=OFF#<CR>
<CR>*pow=?#<CR>
<CR>*POW=ON#<CR>(or *POW=OFF#)
<CR>*sour=RGB#<CR>
<CR>*SOUR=RGB#<CR>
<CR>*sour=vid#<CR>
<CR>*SOUR=VID#<CR>
<CR>*sour=svid#<CR>
<CR>*SOUR=SVID#<CR>
<CR>*sour=?#<CR>
<CR>*SOUR=RGB#<CR>(*SOUR=VID# / *SOUR=SVID#)
<CR>*con=+#<CR>
<CR>*CON=+#<CR>
<CR>*con=-#<CR>
<CR>*CON=-#<CR>
<CR>*con=?#<CR>
<CR>*CON=___#<CR> ( ___ is Contrast value.)
<CR>*bri=+#<CR>
<CR>*BRI=+#<CR>
<CR>*bri=-#<CR>
<CR>*BRI=-#<CR>
<CR>*bri=?#<CR>
<CR>*BRI=___# <CR> ( ___ is Brightness value)
<CR>*asp=4:3#<CR>
<CR>*ASP=4:3#<CR>
<CR>*asp=16:9#<CR>
<CR>*ASP=16:9#<CR>
<CR>*asp=AUTO#<CR>
<CR>*ASP=AUTO#<CR>
<CR>*asp=REAL#<CR>
<CR>*ASP=REAL#<CR>
<CR>*ltim=?#<CR>
<CR>*LTIM=___#<CR> ( ___ is Lamp used hour.)
<CR>*lampm=lnor#<CR>
<CR>*LAMPM=LNOR#<CR>
<CR>*lampm =eco#<CR>
<CR>*LAMPM=ECO#<CR>
<CR>*lampm=?#<CR>
<CR>*LAMPM=LNOR#<CR>(*LAMPM=ECO#)
<CR>*blank=on#<CR>
<CR>*BLANK=ON#<CR>
<CR>*blank=off#<CR>
<CR>*BLANK=OFF#<CR>
<CR>*blank=?#<CR>
<CR>*BLANK=ON#<CR>(*BLANK=OFF#)
<CR>*freeze=on#<CR>
<CR>*FREEZE=ON#<CR>
<CR>*freeze=off#<CR>
<CR>*FREEZE=OFF#<CR>
<CR>*freeze=?#<CR>
<CR>*FREEZE=ON#<CR>(*FREEZE=OFF#)
<CR>*menu#<CR>
<CR>*MENU#<CR>
<CR>*up#<CR>
<CR>*UP#<CR>
<CR>*down#<CR>
<CR>*DOWN#<CR>
<CR>*right#<CR>
<CR>*RIGHT#<CR>
<CR>*left#<CR>
<CR>*LEFT#<CR>
<CR>*enter#<CR>
<CR>*ENTER#<CR>
<CR>*auto#<CR>
<CR>*AUTO#<CR>
<CR>*zoomI#<CR>
<CR>*ZOOMI#<CR>
<CR>*zoomO#<CR>
<CR>*ZOOMO#<CR>
State(The command is acceptable in green state.)
ACK
Standby
Logo
Searching
Source Display
Cooling
This command is acceptable when picture menu setting is user1 or user2.
This command is acceptable when picture menu setting is user1 or user2.
This command is acceptable when picture menu setting is user1 or user2.
This command is acceptable when picture menu setting is user1 or user2.
Show the Lamp used time.
Auto signal select and position.
Note
Advertisement
