Mitsubishi WD3300U User Manual
  1. Manuals
  2. Brands
  3. Mitsubishi Manuals
  4. Projector
  5. DLP XD3200U
  6. User manual

Mitsubishi WD3300U User Manual

Lan control utility
Hide thumbs Also See for WD3300U:
Table of Contents

Advertisement

Quick Links

LAN Control Utility
User Manual (for WD3300U)
Preparation/SetUp .........................................................................2
Preparation before using the network function ...........................................2
Connection ..................................................................................................3
Installation ...................................................................................................3
Setting the IP address of the projector .......................................................5
When using a DHCP server ...........................................................................................6
When not using a DHCP server .....................................................................................7
Telnet setting ...............................................................................................8
Setting the password (Password Setup) .......................................................................9
Setting the display language of ProjectorView (language) ..........................................10
Setting the LAN control (LAN-Controlled Mode) .........................................................10
Save and exit ...............................................................................................................11
ProjectorView ...............................................................................12
Using the ProjectorView ............................................................................12
How to start up ............................................................................................................12
VIRTUAL REMOTE controller .......................................................................................14
E-mail notification function ..........................................................................................14
Initial setting .................................................................................................................15
Support for the PJLink™ function ...............................................16
Contents
EN-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WD3300U and is the answer not in the manual?

Questions and answers

Related Manuals for Mitsubishi WD3300U

Summary of Contents for Mitsubishi WD3300U

  • Page 1: Table Of Contents

    LAN Control Utility User Manual (for WD3300U) Contents Preparation/SetUp .................2 Preparation before using the network function ...........2 Connection ....................3 Installation ....................3 Setting the IP address of the projector ............5 When using a DHCP server ...................6 When not using a DHCP server ..................7 Telnet setting ....................8...

  • Page 2: Preparation/Setup

    Preparation/SetUp Preparation before using the network function This projector is equipped with the network function to control and monitor the projector’s operations using a Web browser and to send e-mail notification. Before using the network function, perform the following three preparation steps. (1) Setup of the application software “Projector-Control Device Installer”...

  • Page 3: Connection

    Preparation/SetUp (continued) Connection Computer LAN cable (option) (100BASE-TX or 10BASE-T should be supported.) External HUB To LAN terminal LAN cable (option) (100BASE-TX or 10BASE-T should be supported.) • Use a straight-through category-5 cable for LAN connection. • Don’t touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged from your body, causing damage to the projector.
  • Page 4 Preparation/SetUp (continued) Select a folder to install the program, and click Next. Click Next. Installation starts. • The progress of the installation process is displayed as shown on the right. When the installation process is completed, click Close. How to remove Projector-Control Device Installer Select [Start] - [Control Panel] - [Add or Remove Programs] - [Projector-Control Device Installer] and click [Remove] (in the case of Windows XP).

  • Page 5: Setting The Ip Address Of The Projector

    Preparation/SetUp (continued) Setting the IP address of the projector Before setting the IP address, check that the projector has been LAN-networked and turn on the main power of the projector. • When using multiple projectors, connect and configure them one by one. If you turn on the powers of the projectors that are connected but not yet configured at the same time, they may not be recognized.

  • Page 6: When Using A Dhcp Server

    Preparation/SetUp (continued) When using a DHCP server Select [Obtain an IP address automatically] and click Next. Click Next. • Check that the options are marked with checkmarks as shown on the right. Keep them unchanged for normal use. Click Assign. Click Finish.

  • Page 7: When Not Using A Dhcp Server

    Preparation/SetUp (continued) When not using a DHCP server Select [Assign a specific IP address] and click Next. Enter a fixed IP address (for example, 192.168.0.1) and click Next. (Note) Do not use 0 or 255 for the last digit of the IP address.

  • Page 8: Telnet Setting

    Preparation/SetUp (continued) Telnet setting Setting of password, display language, LAN control, and PJLink™ certification using telnet. This section describes how to set the password, display language on the ProjectorView screen, LAN control, and PJLink™ certification that are necessary for the operation state control tool (commercially available) that uses the projector operation control/monitor tool ProjectorView and the industry standard PJLink™...

  • Page 9: Setting The Password (Password Setup)

    Preparation/SetUp (continued) Setting the password (Password Setup) Enter “0” and press the Enter key. Input the old (current) password and press the Enter key. (Default password is admin.) • If you input a wrong password, an error message appears and the setting menu is displayed again. In this case, set the password again.

  • Page 10: Setting The Display Language Of Projectorview (Language)

    Preparation/SetUp (continued) Setting the display language of ProjectorView (language) Enter “1” and press the Enter key. Enter “0” for English or “1” for Japanese. Setting the LAN control (LAN-Controlled Mode) Enter “3” and press the Enter key. To enable the e-mail notification function of ProjectorView, enter “1”...

  • Page 11: Setting The Pjlink™ Certification (Pjlink Certification Mode)

    Preparation/SetUp (continued) Setting the PJLink™ certification (PJLink certification Mode) Enter “5” and press the Enter key. • When you don’t use PJLink™ protocol communication, skip this item. (See page 16 for PJLink™.) To enable the PJLink™ certification, enter “1” and press the Enter key.

  • Page 12: Projectorview

    ProjectorView Using the ProjectorView This section describes ProjectorView, a tool to control and monitor the projector’s operations by a Web browser. The major functions of ProjectorView are: • Power on/off • Input source switching • State information indication (projector’s name, temperature, lamp operation time, error/alert, etc.) •...
  • Page 13 ProjectorView (continued) The password input screen appears. Enter the password you set. • The default password is admin. (Note) If you input a wrong password 4 successive times, the Web browser is closed. In this case, repeat from step 1. The ProjectorView main screen appears.

  • Page 14: Virtual Remote Controller

    The lamp has reached its maximum usage. Replace the lamp and reset lamp counter. See user guide for complete instructions. Projector name : abc Projector model : WD3300U Projector location : 10Factory-5F Serial number : 12345 Operating hours : 2146 hours and 43 minutes...

  • Page 15: Initial Setting

    ProjectorView (continued) Initial setting To load information on the projector such as model name and lamp operating time, set the projector data in advance. Click the SETUP button on the ProjectorView main screen. The Projector Setup screen appears. Enter data according to the description of each setting item. (Note) • You can’t change the Projector model, Serial number, Operating hours, and Lamp hours.

  • Page 16: Support For The Pjlink™ Function

    INF1? Inquiry about the “MITSUBISHI” is returned. manufacturer name INF2? Inquiry about the “WD3300U” is returned. model name INF0? Inquiry about other No other information is available. No parameter is returned. information CLSS? Inquiry about the “1” is returned.
  • Page 17 Support for the PJLink™ function (continued) [Notes on Instant Shut Down] Instant shutdown of the projector during control using the network function may cause ProjectorView to fail to display data correctly. • The operating time and temperature may not be displayed correctly. In this case, close the browser, recognize this projector using Projector-Control Device Installer, and then start the browser again.

Table of Contents