Advertisement
The GPSMAP 3000 series chartplotter and GPS antenna must be properly installed according to the following instructions. You need the
appropriate fasteners, tools, and mounts listed in each section. These items are available at most marine dealers. Always wear safety goggles,
ear protection, and a dust mask when drilling, cutting, or sanding. When drilling or cutting, always check what is on the opposite side of the
surface. Mount the GPSMAP 3000 series chartplotter in a location that provides a clear, glare-free view of the display and easy operation of the
controls or touch screen. If you experience difficulty installing the chartplotter, seek the assistance of a professional installer; or contact
Garmin
Product Support by phone at 913/397.8200 or 800/800.1020. Go to www.garmin.com/support. In Europe, contact Garmin
®
(Europe) Ltd. at 44/0870.8501241.
Before installing your GPSMAP 3000 series chartplotter, confirm that the package contains the items listed on the box. If any parts are missing,
contact your Garmin dealer immediately.
WARNING: See the Important Safety and Product Information guide in the product box for product warnings and other important
information.
To install the GPSMAP 3000 series chartplotter:
1. Mount the GPSMAP 3000 series chartplotter (Page 1).
2. Mount the GPS antenna (Page 3).
3. Connect the GPSMAP 3000 series device to power and to the GPS antenna (Page 6).
4. Ensure the chartplotter software is up-to-date (Page 10).
Although they are not necessary to use the GPSMAP 3000 chartplotter, you can also use this manual to:
•
Connect the chartplotter to NMEA 0183-compatible devices such as a VHF radio with DSC
•
Connect the chartplotter to an external alarm
•
Connect the chartplotter to a video input source
•
Connect the chartplotter to an external video monitor
•
Connect the chartplotter to other Garmin Marine Network compatible devices, such as a sounder or a radar
You can use the included bracket to bail mount the chartplotter, or you can use the included template and hardware to flush mount the
chartplotter.
Bail Mounting the GPSMAP 3000 Series Chartplotter
Use the included bracket to bail mount the GPSMAP 3000 series chartplotter.
Tools required (not included):
• Drill and drill bit
• Screwdriver
• Pencil
• Mounting hardware (screws or nuts, washers, and bolts)
NotE: The mounting hardware (screws or nuts, washers, and bolts) are not included. The holes on the bail mount are
Choose mounting hardware that fits the holes in the bail mount and securely attaches it to your specific mounting surface. The size of the drill bit
required depends on the mounting hardware chosen.
August, 2008
GPSMAP
3000 Series Installation Instructions
®
(Page
8).
(Page
Mounting the GPSMAP 3000 Series Chartplotter
8).
(Page
8).
190-00991-02 Rev. A
(Page
6).
(Page
9).
/
in. (7.9 mm) in diameter.
5
16
Printed in Taiwan
Advertisement
Table of Contents
Related Manuals for Garmin 3000
Summary of Contents for Garmin 3000
- Page 1 When drilling or cutting, always check what is on the opposite side of the surface. Mount the GPSMAP 3000 series chartplotter in a location that provides a clear, glare-free view of the display and easy operation of the controls or touch screen.
- Page 2 Flush Mounting the GPSMAP 3000 Series Chartplotter Use the included flush-mount template and hardware to flush mount your GPSMAP 3000 series chartplotter. NotE: Make sure the surface on which you mount the chartplotter has at least 2 in. (5.1 cm) of open space behind it to fit the chartplotter and the connected wires.
-
Page 3: Installing The Gps Antenna
9. Place the chartplotter into the cutout. The four mounting studs should feed through the four mounting holes drilled in Step 8. 10. P lace the flat washers over the mounting studs, then thread the hex nuts onto the mounting studs. Tighten all four hex nuts evenly until the chartplotter is snug against the mounting surface. To install the GPS 17x antenna, select a suitable location, mount the antenna, and connect the antenna to power and to your GPSMAP 3000 series chartplotter. Mount the GPS 17x Antenna You can surface mount the GPS 17x antenna, attach it to a standard 1 in. OD pipe-threaded-pole marine mount (14 threads-per-inch—not included), or even install the antenna under fiberglass. - Page 4 ➋ ➊ ➊ Pole-mount Pole-mount adapter adapter Vertical cable Vertical cable slot slot GPSMAP 3000 Series Installation Instructions Best Best Good Good 3 ft. 3 ft. (1 m) (1 m) VHF Radio Antenna VHF Radio Antenna ➋ ➋...
-
Page 5: Wiring And Cables
The GPSMAP 3000 series chartplotter comes with a Power/data cable, and a GPS 17x cable. Additionally, the GPSMAP 3006, 3206, 3010, and 3210 chartplotters come with a 17-pin Marine Video cable. Optional Garmin Marine Network components use specialized Garmin Network cables. -
Page 6: Power/Data Cable Wiring
Power/Data Cable Wiring The following pages contain several wiring diagrams. The first diagram on the next page is a simple diagram showing the GPSMAP 3000 series chartplotter using the 18-pin Power/data cable and the GPS 17x. If two or more GPSMAP 3000, 4000, or 5000 series chartplotters are installed and networked, only one GPS 17x antenna needs to be installed. - Page 7 Garmin GPSMAP 3000 Series Chartplotter Garmin GPSMAP 3000 Series Chartplotter GPSMAP 3000 Series Chartplotter Wired to a NMEA Device With Two-way Communication Garmin GPSMAP 3000 Series Chartplotter GPSMAP 3000 Series Chartplotter Wired to a NMEA Device With One-way Communication Garmin...
- Page 8 Wiring to an Optional Alarm The GPSMAP 3000 series chartplotter can be used with a lamp, a horn, or both, to sound or flash an alert when the chartplotter displays a message. The alarm does not need to be wired for the GPSMAP 3000 chartplotter to function. The alarm circuit switches to a low-voltage state when the alarm sounds.
-
Page 9: Garmin Marine Network
If more than two GPSMAP 3000 series chartplotter are installed, use a Garmin Marine Network Port Expander (GMS 10) to expand the network. If two or more GPSMAP 3000 series chartplotters are installed and networked, only one GPS 17x antenna needs to be installed. You can add up to five total devices to the Network Port Expander. -
Page 10: Updating The Chartplotter Software
4. If you are connecting the GPSMAP 3000 series chartplotter to a Garmin Marine Network, insert the RJ-45 connector into the NETWORK port on the back of the unit and screw the locking ring in clockwise until it is firmly seated. With power applied to the circuit, test the installation by pressing the PoWER key on the front of the unit. Refer to your GPSMAP 3000 series Owner’s Manual for steps on initializing and using the chartplotter. Your GPSMAP 3000 series chartplotter may contain a software update Data card. If so, follow the instructions provided with the card.