Garmin nüvi 660 Installation Instructions
Garmin motorcycle navigator installation instructions
Hide thumbs
Also See for nüvi 660:
- Quick reference manual (2 pages) ,
- Owner's manual (72 pages) ,
- Specifications (2 pages)
Advertisement
Table of Contents
- 1 Mount Your Zūmo on the Motorcycle
- 2 Step 1: Connect Power to the Mount
- 3 Step 2: Install the Handlebar Base
- 4 Step 3: Attach the Base Plate to the Zūmo Mount
- 5 Step 4: Attach the Base Plate to the Handlebar Base
- 6 Step 5: Install Your Zūmo in the Mount
- 7 Remove Your Zūmo from Either Mount
- 8 Mount Your Zūmo in an Automobile
- Download this manual
zūmo 660 Installation Instructions
Mount Your zūmo on the Motorcyle
Warning: Incorrectly wiring the power cable with bare wire leads can result in
damage to the vehicle or the battery and can cause bodily injury. Garmin strongly
recommends having an experienced installer with the proper knowledge of electrical
systems install the unit.
See the Important Safety and Product Information guide in the product box for product warnings
and other important information.
Step 1: Connect Power to the Mount
Select a suitable and secure location to mount the zūmo on your motorcycle, based on
available power sources and safe cable routing.
Cradle
Power cable
Microphone jack (2.5 mm)
Step 2: Install the Handlebar Base
The zūmo includes parts for two handlebar installation solutions. Custom mounts can
require additional hardware (www.ram-mount.com).
A) To install the U-bolt and handlebar base:
1. Place the U-bolt around the handlebar, and thread the ends through the handlebar
base.
2. Tighten the nuts to secure the base. Do not overtighten.
note: The recommended torque is 50 lbf-in. Do not exceed torque of 80 lbf-in.
Handlebar
Headphone/audio out jack (3.5 mm)
Bare wires with
inline fuse for
power connection
Mini-USB connector
(for traffic receiever)
Handlebar
base
U-bolt
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Garmin nüvi 660
Summary of Contents for Garmin nüvi 660
- Page 1 Mount Your zūmo on the Motorcyle Warning: Incorrectly wiring the power cable with bare wire leads can result in damage to the vehicle or the battery and can cause bodily injury. Garmin strongly recommends having an experienced installer with the proper knowledge of electrical systems install the unit.
- Page 2 B) To install the handlebar base to the clutch/brake clamp bracket: note: Both 1/4 in. standard and M6 bolts are included. Match the size of the factory bolts on your clutch/brake clamp bracket. 1. Remove the two factory bolts on your clutch/brake clamp bracket. 2. Thread the new bolts through the handlebar base, spacers, and clamp bracket. 3. Tighten the bolts to secure the base. Step 3: Attach the Base Plate to the zūmo Mount 1. Thread the M4 × 40 mm panhead screws through the washers, cradle, spacers, and base plate.
- Page 3 Step 4: Attach the Base Plate to the Handlebar Base 1. Align the ball of the handlebar base and the ball of the base plate with the double- socket arm. 2. Tighten the knob slightly. 3. Adjust for better viewing and operation. 4. Tighten the knob to secure the mount. Cradle Cradle Step 5: Install Your zūmo in the Mount 1. Fit the bottom of your zūmo into the cradle. 2. Tilt the zūmo back until it snaps into place. Remove Your zūmo from Either Mount 1. Press the button on the side of the mount to release the zūmo. 2. Lift out the zūmo.
- Page 4 Garmin Ltd. or its subsidiaries, registered in the USA and ® ® other countries. These trademarks may not be used without the express permission of Garmin. Other trademarks and trade names are those of their respective owners. January 2009...
Need help?
Do you have a question about the nüvi 660 and is the answer not in the manual?
Questions and answers