DOD VoTec Manual

Multi effects processing

Advertisement

C A U T I O N
R I S K O F E L E C T R I C S H O C K
D O N O T O P E N
A T T E N T I O N :
RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR
W A R N I N G :
T O R E D U C E T H E R I S K O F F I R E O R E L E C T R I C
S H O C K D O N O T E X P O S E T H I S E Q U I P M E N T T O R A I N O R M O I S T U R E
WARNING
FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (e.g. near a
bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming
pool, etc). Care should be taken so that objects do not fall and liquids are not spilled
into the enclosure through openings.
POWER SOURCES: The appliance should be connected to a power supply only of
the type described in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the ground-
ing or polarization means of an appliance is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience receptacles, and the point where
they exit from the appliance.
SERVICING: To reduce the risk of fire or electric shock, the user should not attempt
to service the appliance beyond that described in the operating instructions. All other
servicing should be referred to qualified service personnel.
FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE RECEPTACLE:
Replace fuse with same type and rating only.
ELECTROMAGNETIC COMPATIBILITY
Operation is subject to the following conditions:
• this device may not cause harmful interference, and
• this device must accept any interference received, including interference
that may cause undesired operation.
• use only shielded interconnecting cables.
• operation of this unit within significant electromagnetic fields should be
avoided.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VoTec and is the answer not in the manual?

Questions and answers

Summary of Contents for DOD VoTec

  • Page 1 C A U T I O N R I S K O F E L E C T R I C S H O C K D O N O T O P E N A T T E N T I O N : RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR W A R N I N G : T O R E D U C E T H E R I S K O F F I R E O R E L E C T R I C...
  • Page 2 When the desired effect has been found, press the Store Button (6). When the Store Button (6) has been pressed, the store light will blink, this is the VoTEC asking where you would like the program saved. Use the Up/down buttons (9) to select desired pro- gram number, press the Store Button (6) one more time to save.
  • Page 3 DOD WITH RETURN AUTHORIZATION, where all parts and labor will be covered up to a period of one (1) year. A Return Authorization number may be obtained from DOD by telephone. The company shall not be liable for any consequential damage as a result of the product’s use in any circuit or assembly.
  • Page 4 10. Input Knob Controls the overall input level from your mic. 11. Clip LED The clip LED lights when clipping occurs at the input of the VoTEC, To eliminate clipping, reduce the setting of your input level by adjusting the Input knob. Allow the LED to light occasionally with peak signals.
  • Page 5 DIGITAL/ANALOG PRESETS FX LIS S T T FACT T O O RY Y P P RES S ET T S S Master Level: 0-99 Mix Level: 0-99 BANK 1 Noise Gate/F.B.S.: 01- Vocal Chorus with Delay and Reverb G1-9: Increase gate threshold and hysteresis 02- Vocal Delay “Slappin’...
  • Page 6 S H O C K D O N O T E X P O S E T H I S E Q U I P M E N T T O R A I N O R M O I S T U R E VoTEC Input Connection: Insert XLR cable from microphone to VoTEC input. Output Connection: Insert XLR cable from VoTEC out- input...

Table of Contents