Daikin FXTQ12PAVJU Installation Manual page 17

(12) -2 Electric heater operating mode setting
〈When electric heater is used in "Heat Pump lockout
mode"〉
• Check the heater capacity. (Select heater marked with "
2
" " in Table 8.)
• Perform on-site setting using the remote controller.
• Set the "heat pump lockout mode" using the outdoor unit.
(Refer to the service manual for the outdoor unit.)
〈When used as "Auxiliary electric heater"〉
• Check the heater capacity. (Select heater marked with "
Table 8.)
• Perform on-site setting using the remote controller.
Table 8
Electric heater kit model name
Model
HKR- HKR- HKR-
03 05C
12 type
1
18 type
24 type 1
30 · 36 type 1 1
1 1
42 type
48 · 54 type 1 1
Electric Heater kit setting
Mode No.
(Optional kit)
Heat Pump lock out mode
Auxiliary electric heater &
Heat Pump Lockout mode
available
* factory set
(12) -3 Electric heater ON/OFF temperature setting
• While in heating operation, the heater control (ON/OFF) is
conducted as shown below;
ON
<Ton: F°>
• Perform on-site setting using the remote controller.
FIRST
Mode
CODE CODE
No.
01*
NO.
<Ton> -7.2
10 (20) 7
<Toff> -3.6
* factory set
10-6 SETTING FOR LOCAL SUPPLIED OPTION.
(1) Installation of the humidifi er, economizer and air
purifi er (UV lamp)
• Humidifi er, economizer and air purifi er (UV lamp) are
sold separately. For the method of installation, refer to
the manual provided with each optional product.
English
HKR- HKR- HKR- HKR-
06 08C 10C 15C 20C
1 1 2
1 1 2
FIRST SECOND
CODE NO. CODE NO.
01*
03
11 (21) 3
Set temperature
OFF
<Toff: F°>
SECOND CODE NO.
02 03 04 05 06
-6.3 -5.4 -4.5 -3.6 -2.7
-2.7 -1.8 -0.9 0 0.9
WARNING
• If the unit is installed with an electric heater, install the
optional product at a location where it is not exposed directly
" or
to the heat from the electric heater. Direct exposure to heat
can result in an equipment malfunction or fi re.
(2) Connect the wires
• Run the wires through the low-voltage hole.
• Connect the wires to the terminal block (10P) of the
1 " in
product. The terminal Nos. for wire connection are
shown below. Refer to the information as needed.
Terminal Nos. are indicated on the name plate for the
terminal block.
2
Terminal No. Input/output signal
1, 2
3, 4
5, 6
7, 8
9, 10
(3) On-site setting of air purifi er/humidifi er
Mode No. FIRST CODE NO .
14 (24) 4 FAN SPEED
UNDER
OPERATING
purifi er and
humidifi er
14 (24) 5 FAN RESI-
DUE TIME
FOR HUMIDI-
FIER
* factory set
10-7 SETTINGS FOR SEPARATELY SOLD ACCES-
SORIES
• See the instruction manuals included with optional accesso-
ries for the necessary settings.
Outputs: indoor unit ON signal. (AC 24V)
Outputs: indoor unit cooling THERMO ON
signal. (AC 24V)
Receives input: Air purifi er operation ON
signal. (dry contact)
Receives input: Humidifi er operation ON
signal. (dry contact)
Receives input: Forced closure of Indoor Unit
Electronic Expansion Valve during cooling
operation. (dry contact)
01 02
Refer to
remote
controller H*
setting
SPEED
30 [sec] 60* [sec]
Terminal
block (10P)
03
120 [sec]
16