Electrolux EIDW6405HT - Fully Integrated Dishwasher Installation Instructions page 2

1. Measure height of cabinetopening from underside of
countertop tofloor. Check chartfor height opening and
suggested adjustment.
Leg Leveler Adjustment Chart
Heightof Number of Tumsto
Cabinet Opening Adjust Levelers
34"(86.4cm) 0
34 _8"(86.7cm) 2
34 _" (87.2cm) 6
34_z"(87.6cm) 9
2, Move dishwasher to front of installation area.
3. Loosen the rear ]evefing legs by turning counterclockwise. Refer
to chart for number of turns.
Dishwasher Anchoring
4. instal] the Cabinet Seal Kit (Instn.lctions included in Kit)
5. Choose one of the methods of attachment below to secure unib
holes need to be pre-ddlled using a #5 ddll bit regardless of
the option chosen:
a. Side Mount Cabinet Clips (Preferred Method of
attachment)
b. Top Mount Cabinet Clips (to be used when Side Mount
is not an available option)
CAUTION: Use extreme care in mounting the dishwasher as to
not scratch, bump or otherwise damage the console or tub.
To install the Side Mounting Clips,
Depending on space allowed in cabinet the Side Mounting
Clips can be installed with the holes for the screw Lip (preferred
method) or down as shown in the illustrations below. (Use extreme
caution when the dips are in the down position while installing
the dishwasher).
NOTE: Install Side Mount Brackets before unit is installed into
the cabinet. Insert screws intothe front holes of the
mounting clips only. (See image below)
Use {f measures 341/_ '' to 35"
Use if measu,_s 34" to 34V_"
TO install using Top Mou nt Cabinet Clips: Depending on the
depth of cabineb the Top Mount Clip have a break off point
that can be removed if necessary.
NOTE: Install Top Mount Clips before unit is installed into
the cabinet. Screw clips flrrnly to top brace using screws
provided in the literature pack. (See image below)
6, If levelers need to be removed, make sure that the floor is free of all
obstr_lcfions.
7. Care fully place dishwasher inside cabinet area such that is
centered in opening. Use caution when moving dishwasher to
prevent damage to cabinet, dishwasher and floor.
8. Front of door needs to be even with the front of adjoining cabinets.
Front levelers ShOLddallow 5/16" below underside of countertop
to top of console.
9. Check that dishwasher is level from side to side by placing a level
against the top front section of the tub. See Figure 6a.
10. Check that the dishwasher is level from front to back by taking
out the lower rack, place level on the lower rack wheel support at
the bottom of the tub. See Figure 6b.
11. Adjust levelers Lip or down until dishwasher is level.
Holes need to be pre-drified using a #5 drill to secure unit.
12. Screw mounting brackets firmly to cabinet using screws provided
in literature packet. See Image Below.
Figztre 6c Figttre 6d
13. Open and close dishwasher door slowly. Ensure that there is
clearance to the console. Adjust accordingly unfil door opens
and closes freely.
Property Damage
Do not solder within 6" of the water inlet valve. Damage to
the plastic parts in the valve may occur.
Use care that no sealer, dirt, or other objects enter the valve.
Damage to the filter screen may occur.
Be sure the dishwasher is placed where the water inlet
valve will be kept from freezing. If the valve freezes, it may
rupture and flooding may occur.
Water Line
1, FlUsh water line before connecting it towater inlet valve to
prevent early clogging of filter screen. Place a bunched towel
over end of line to prevent splashing. Open water supply valve for
a few seconds and let water drain into a pan. Turn off water
supply at shut-off valve.
2. Rot.de water line to water inlet valve as shown in Figure 5.
3. While firmly pulling water supply line into 90 ° elbow, tightly
connect water supply to water inlel valve. Supply line must be
free of kinks, scales, chips, and lubricants.
4. Turn on water supply and check for leaks.
Electrical Supply
1. Remove junction box cover and pui] house widng into junction
box. See Figure 7a.
2, Use a UL listed conduit connector (not included) at box to
stabilize wiring.
3. Connect incoming black lead to dishwasher's black lead,
incoming white lead to dishwasher's white lead and incoming
green lead to dishwasher's green lead with wire nuts. (See
Grounding Instruction Warning). Wire nuts must be tight.
4. Replace junction box cover.
Box
White Wire
Junction Wire to White Wire
Box Cover to Black Wire (Neutral)
Figm'e 7a (Hot)
Figure 71)
check these items:
Water and electrical lines are straight out in front of the
dishwasher.
All four leg levelers are positioned properly.
Cabinet Seals are positioned on the sides and top of the
dishwasher.
Cabinet Attachment Clips are attached to the cabinet on
both comers on top of the dishwasher.
Replace Toe and Kickplate. Note: When replacing Toe
and Kickplate hand tighten screws.
Electric Shock Hazard
Grounding Instructions:
The dishwasher must be connected to a grounded metal,
permanent wiring system or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the appliance's equipment grounding terminal
or lead. ]t is the consumer's responsibility to contact a
qualified installer to make sure the electrical installation
conforms with the National Electrical Code and local codes
and ordinances.
Do not connect the dishwasher to the power supply until the
appliance is permanently grounded.
All wiring connections must be enclosed in the junction box.
This unit has copper lead wires.
Joining aluminum building wire to stranded copper wire
should be done by a qualified electrician using materials
recognized by UL and local codes.
Do not use an extension cord. Such use can result in fire,
electrical shock, or other personal injury.
Failure to follow these instructions could res ult in death or
serious injury.
1. Review Figures 8, 9 and 10 to see the different ways to connect
dishwasher to drain system. Choose method that best suits
yourneed.
Jf Sink at R_h,
Sink ,t L_#
F_.re 8
The drain hose h)op mu_t be at least 32" high [rom the [Ioor
to insuraproper draimtga,
2, If you connect to a sink drain, entry will need to be above trap.
A "Y" branch tailpiece and connector kit, not included, will make
this method easier and includes all needed fillings and
instructions. See Figure 8.
3. If you connect to a sink trap, local codes may require you to
install an air gap kit, (not included). The drain hose will be routed
from dishwasher to air gap inlet as shown in Fig ure 9. An air
gap kit is available from a plumbing supply store. (If the drain
hose is installed through the floor, an air gap is necessary).
4. If you connect to a disposer, the large end of drain hose will fit.
Fig ure 10(a). The knock out plug must be removed from
inside disposer inlet before making the final fit to drain
hose See Figure 10(b).
/
Figttre lOpO Cuth_t 3/4"_,mne_tion,
Sink at Le# _ "_a_a_tit Gap
C _\ ' " _D "
109(b)
The drain hose h)op mu_t be at h,a_t 32" high [rom the [loor
to insm'e proper _'ainag_
5. [fthe cabinet wall is wood, sand edges of hole until smooth and
rounded. If cabinet wall is metal, cover all sharp edges with
eleclrical or duct tape to avoid cutting drain hose.
Move unit back in place while routing drain hose through access
hole. Use caution to prevent damage to the dishwasher, floor and
cabinets. IMPORTANT: Make sure there are no sharp bends
or kinks that might restrict drain flow.
Secure drain hose to sink drain, disposer, or separate trap with a
clamp. IMPORTANT: Be careful not to overtighten clamp or
you may damage end of hose. Do not connect hose to
horizontal pipe between sink drain and disposer.
Be sure unit does not rest on drain hose. I_should be free of
electrical components and door spnngs. Do not cut corrugated
drain hose. PLdl excess through cabinet and place under sink.
Make sure hose does not come in contact with any sharp edges.
Electric Shock Hazard
Disconnect electrical power at the fuse box
or circuit breaker box before beginning
installation.
Failure to follow this warning could result in
death or serious injury.
Failure to follow this warning may result in
injury.
check these items:
Water and drain lines have no kinks and move freely
behindthe dishwasher.
Water supply is turned on.
Joints are free of leaks.
Wiring connections to junction box are tight all access
panels are secured back in place.
Replace kickplate. See Figure 1
Drain hose is assembled to Drain Hose Connector.
All packing materials and consumer literature have
been removed from inside unit.
Dishwasher is level and securely fastened.
Open and dose door to make sure it does not hit
surrounding cabinet or countertop.
Make sure that all wire ties are removed from the Adjustable
Rack Assembly, Versa Tray, Utility Tray and Silverware
Baskets.
Operate the machine through at
least one fill and pump-out,
checking the following items:
On EIDW6405HT press and hold SANITIZE keypad for 8
seconds before first use.
At first fill, approximately 2 minLdes, make sure water
completely covers filter surface.
At pump-ouh (pump_ut is either when the cycle is
completed or canceled, refer to the Use and Care Guide
for Stad/Cancel), make sure all water is pumped ouk
Check water connections again for leaks.