Important Safety Information Improper handling can cause serious damage to the KoldFront ice maker and/or injury to the user. This ice maker is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other use may invalidate the warranty.
LIMITED WARRANTY ..................17 This owner’s manual is provided for reference use only. Specifications may change without prior notice. Refer to the product label on the back of your ice maker for the latest technical information. KoldFront Built-in Ice Maker...
Introduction Thank you for purchasing this KoldFront ice maker. We are glad you chose us. We believe that your purchase of this product opens a relationship between you and KoldFront. We will provide the customer support needed to nurture that relationship.
Parts Identification Front View Hinge Ice Mold Water Trough Door Float Ice Bin Selector Switch Leveling Foot Back View Control Panel Ice Scoop Power Plug Water inlet Drain outlet KoldFront Built-in Ice Maker...
Installing the Ice Maker The ice maker should be installed by a licensed plumber to be in accordance with local electrical and plumbing code requirements. Before you plug the ice maker in to a power supply, be sure to let it stand upright for at least 24 hours to allow the compressor’s oils to settle.
A standard electrical supply (115 VAC only, 60 Hz, 15 A), properly grounded in accordance with National Electrical Code and local codes and ordinances is required. • IMPORTANT: Do not kink or pinch the power supply cord between the ice maker and wall or cabinet. KoldFront Built-in Ice Maker...
Electrical Requirements Electrical Shock Hazard Plug into a grounded 3-prong outlet. Never remove the grounding prong from the plug. Never use an adapter. Never use an extension cord. Failure to follow these instructions can result in fire, electrical shock, or death Before you move your icemaker into its final location, it is important to make sure you have the proper electrical connection: A standard electrical supply (115 V, 60Hz.), properly grounded in...
2. Remove the bottom hinge, place on the opposite side at the bottom of the door. 3. Position the door on the bottom hinge. 4. Align the door on the bottom hinge and replace the top hinge. 5. Push the plug buttons into the original screw holes. KoldFront Built-in Ice Maker...
Water Supply Connections The water supply should be ready at the point of installation. The water supply pressure should be a minimum of 15 psig with a static pressure not more than 80 psig. (A wall outlet directly behind the ice maker will make installation easier.) IMPORTANT: 1.
During this stage, the compressor works regularly to keep the temperature lower to reduce ice melting. 5. The unit will start making ice again after the ice cubes are removed. At that time, the ice-full probe swings back to operating position. KoldFront Built-in Ice Maker...
IMPORTANT: • Although the unit has been tested and cleaned at the factory, due to long-term transit and storage, the first batch of cubes must be discarded. • Never turn the water supply tap off when the ice maker is working. •...
8. Leave the water supply line and power cord disconnected until ready to reuse. IMPORTANT: • Do not touch the power plug when your hands are wet. • Never unplug the unit by pulling on the plug. KoldFront Built-in Ice Maker...
CLEANING AND MAINTENANCE The icemaker must be thoroughly cleaned if it has been left unused for a long time. Follow carefully any instructions provided for cleaning or use of sanitizing solution. Do not leave any solution inside the icemaker after cleaning. Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life.
5. Put back the filter and reassemble the front cover. 6. Plug in the icemaker or reconnect power. DO NOT touch the condenser fins. They are sharp and can be damaged easily. KoldFront Built-in Ice Maker...
Water Distribution Tube cleaning When you find that the ice cubes are incompletely formed or the output of ice cubes is low, the water distribution tube may be blocked. Set the ICE/OFF/WASH switch to OFF, rotate the water distribution tube, and locate the holes in the distribution tube.
Page 17
5. Ice cube size is adjustable. 6. A sensitive probe and accurate timer enhance the performance of the ice maker. 7. Built-in compressor protection system. KoldFront Built-in Ice Maker...
TROUBLESHOOTING Before Calling for Service If the unit appears to be malfunctioning, read through the OPERATION section of this manual first. If the issue persists, check the troubleshooting section below. The issue could be solved by following the suggestions in the “Solution” column. Issue Possible Cause Solution...
Limited Warranty One (1) Year Parts & Ninety (90) Days Labor This product is warranted by EdgeStar to be free from defective workmanship and materials, subject to any conditions set forth as follows: WHAT IS COVERED: LABOR: For a period of NINETY (90) DAYS from the date of original purchase, labor will be performed free of charge at an authorized EdgeStar repair facility.