Philips CE120/55 Installation & Connection Manual page 2

3
English
a Carry case with front panel stored inside
b Trim plate
These instructions are for a typical installation.
However, if your car has different requirements, c Standard connector
make the corresponding adjustment. If you have
d Disassembly tool x 2 pcs
any questions regarding installation kits, consult
your Philips car audio dealer. e Rubber cushion
f Screw x 4 pcs
Caution
g Mounting bolt
• This unit is designed for negative ground
(earth) 12 V DC operation only.
Connect wires: ISO connectors
• Always install this unit in the car dashboard.
Other locations can be dangerous as the
rear of the unit heats up during use.
To avoid short-circuit: before you connect,
•
Caution
ensure that the ignition is off.
• Ensure that you connect the yellow and red
• Ensure that all loose leads are insulated with
power supply leads after all other leads are
electrical tape.
connected.
• Ensure that all loose leads are insulated with
electrical tape. 1
Pull out the ISO connectors from car dash-
• Ensure that the leads do not get caught
board and connect them to the bigger end
under screws orin parts that will move (e.g.
of the supplied standard connector.
seat rail).
2
Connect the other end of the supplied
• Ensure that all ground (earth) leads are run
standard connector to the unit.
to a common ground (earth) point.
3
Do the other connections, if applicable.
Use only the supplied mounting hardware
•
for a safe and secure installation.
1
Antenna To antenna
• Improper fuses can cause damage or fi re.
When you need to change the fuse, consult
2
Rear line out To amplifi er line
a professional.
(right) in (right)
3
Rear line out To amplifi er line
Note on the power supply lead (yellow)
(left) in (left)
• When you connect other devices to this
unit, ensure that the rating of the car circuit
is higher than the total fuse value of all the
Connect wires: without ISO
connected devices.
connectors
Notes on speaker connection
• Never connect speaker wires to the metal
body or chassis of the car.
Caution
• Never connect speaker wires with stripes to
one another. • Ensure that all loose leads are insulated with
electrical tape.
Overview of parts
1
Cut off the bigger end of the supplied
standard connector.
These are the supplied parts needed to connect
2
Check the car's wiring carefully and connect
and install this unit.
them to the supplied standard connector.
4
1 4
Black To a metal surface of the Do the other connections, if applicable.
car
1
First connect the black Antenna To antenna
ground (earth) lead, then
connect the yellow and red
2
Rear line out To amplifi er
power supply leads.
2 (right) line in (right)
Blue To the electric antenna
control lead or power
3
Rear line out To amplifi er
supply lead of the antenna
(left) line in (left)
booster
If there is no electric an-
tenna or antenna booster,
or it is manually operated
Attach the front panel
telescopic antenna, it is not
necessary to connect this
1
Attach the trim plate.
lead.
2
Insert the left side of the panel in the chassis
3
Yellow To the +12V car battery
until it is correctly engaged.
which is energized at all
3
Press the right side of the panel until it is
times.
locked into place.
4
Pink To telephone mute termi-
nal (if any).
5
Red To the +12V power termi-
Mount into the dashboard
nal which is energized in
the accessory (ACC) posi-
1
Ensure that car dashboard opening is within
tion of the ignition switch
these measurements:
If there is no accessory po-
• If the car dashboard is bigger, the sup-
sition, connect to the +12V
plied mounting sleeve is not suitable for
car battery terminal that
the car. Remove the mounting sleeve
is always live. Be sure to
with the removal keys and consult a
connect the black ground
professional for advice.
(earth) lead to a metal
2
If the car does not have an on-board drive
surface of the car fi rst.
or navigation computer, disconnect the nega-
6
Green/ Left speaker (Rear)
tive terminal of the car attery.
black
• If you disconnect the car battery in
strip
a car that has an on-board drive or
7
White/ Left speaker (Front)
navigation computer, the computer may
black
lost its memory.
strip • If the car battery is not disconnected,
8
Gray/ Right speaker (Front) to avoid short-circuit, ensure that bare
wires do not touch each other.
black
3
strip Connect the supplied mounting bolt to the
unit.
9
Purple/ Right speaker (Rear) 4
Place the supplied rubber cushion over the
end of the mounting bolt.
black
strip
5
Slide the unit into the dashboard until you
hear a click sound.
3
Connect the supplied standard connector to
the unit.
6
Reconnect the negative terminal of the car
battery.
Detach the front panel
You can detach the front panel to deter theft.
1
Press to release the panel.
2
Pull the panel towards you to detach it from
the chassis.
3
Store the panel in the supplied carry case to
protect it from dirt or damage.
Replace fuse
If there is no power, the fuse may broke and need
to be replaced.
1
Detach the front panel and take out the unit.
(see 'Remove the unit' on page 23)
2
Check the electric connection .
3
Buy a fuse that matches the voltage of the
damaged fuse (15A)
4
Replace the fuse.
If the fuse is broken again after replacement, there
might have internal malfunction. In such case,
consult your Philips dealer.
Remove the unit
To repair or replace the unit, remove it from the
dashboard.
1
Detach the front panel.
2
Pull out the unit by using the removal keys.
5
6
7