Advertisement
Quick Links
INSTALLATION INSTRUCTIONS FOR INSTALLING A BLOWER SNAp SWITCh
RETROFIT KIT FOR USE WITh COUNTRY COLLECTION™ MODELS S60, SA60,
SS20, ST20, S260 AND ST30 FREESTANDING WOODSTOVES
KIT CONTENTS
1 ea. Blower Wire Harness (item #1)
1 ea. Snap Switch and Control Panel Housings (item #2)
1 ea. 6" of 3/4" Heat Shrink Tube (item #3)
2 ea. Butt Connectors (item #4)
3 ea. Wire Ties (item #5)
1 ea. Instruction Sheet
TOOLS NEEDED
5/32 Allen Wrench Or T Handle Wrench
Cutting Pliers
Wire Crimpers
9/16" Socket Wrench
9/16" Open End Wrench
Crescent Wrench
3/8" End Wrench
Large Flat Head Screwdriver
5
3
4
Figure 1 - Kit Contents
FREESTANDING BLOWER SNAp SWITCh RETROFIT KIT
Cat. No.
Model
h798
SSK-BLWR-FSB700
2
Description
Blower Retrofit Kit, FS Woodstoves
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
p/N 506033-35
FREESTANDING BLOWER SNAp SWITCh RETROFIT KIT
Rev. NC, /2009
GENERAL INFORMATION
This retrofit kit works in conjunction with the optional 700-CFM room air
circulation blower kit. The kit provides a variable speed control (rheostat)
and snap switch, which will allow for the option of automatic thermal
activation of the blower, when desired and blower speed control (see
Blower Operation on Page 8).
If you encounter any problems, need clarification of these instructions or
are not qualified to properly install this kit, contact your local distributor
or dealer.
Read this instruction sheet in its entirety before beginning the installa-
tion.
ALL WARNINGS AND pRECAUTIONS IN ThE INSTALLATION AND
OpERATION MANUAL pROVIDED WITh ThE AppLIANCE AppLY TO
ThESE INSTRUCTIONS.
ShUT DOWN ThE STOVE AND ALLOW IT TO COMpLETELY COOL BEFORE
pROCEEDING.
The blower must be plugged directly into a properly
grounded three-prong receptacle, 20 VAC, 60 hz, single
phase. Do not cut or remove the grounding prong from
this plug. Do not route power cord under or in front of
appliance.
Installation must be in accordance with National Elec-
trical Code, ANSI/NFpA 70 - latest edition. In Canada,
the current CSA C22- Canadian Electrical Code - latest
edition.
DANGER: Disconnect power before servicing blower.
In the event that you remove the blower for any reason,
make sure a cover plate (available from Lennox hearth
products) is installed before using the heater. Excessive
rear wall temperatures will result if the stove is burned
without the cover plate. The cover plate is not necessary
if a blower has never been installed because a knock-out
will be in place to act as the cover.
HEARTH PRODUCTS
KITS AND ACCESSORIES
COUNTRY COLLECTION™ WOODSTOVES
WARNINGS
Advertisement
Related Manuals for Lennox Hearth Products 506033-35
Summary of Contents for Lennox Hearth Products 506033-35
- Page 1 HEARTH PRODUCTS KITS AND ACCESSORIES p/N 506033-35 FREESTANDING BLOWER SNAp SWITCh RETROFIT KIT Rev. NC, /2009 COUNTRY COLLECTION™ WOODSTOVES INSTALLATION INSTRUCTIONS FOR INSTALLING A BLOWER SNAp SWITCh RETROFIT KIT FOR USE WITh COUNTRY COLLECTION™ MODELS S60, SA60, SS20, ST20, S260 AND ST30 FREESTANDING WOODSTOVES...
- Page 2 INSTALLATION INSTRUCTIONS Removing Existing Blower From Stove Step . UNpLUG pOWER CORD AND ENSURE AppLIANCE IS COLD Step 2. Using a 5/32 allen wrench/T-handle, remove the blower mounting allen screws from blower, and remove blower from stove. See Figure 2. Butt Connectors Blower Cut black wires on motor...
-
Page 3: Table Of Contents
Crimp on butt connectors to both wires Figure 10 Figure 7 Step 0. Reconnect the new ground wire to the motor stud. See Figure Step 8. Slide the supplied 6” of 3/4” heat shrink tube over the (3) blower harness wires. See Figure 8. Green Ground Wire heat shrink tube Figure 8... -
Page 4: Figure
Step 2. Shrink the tube with heat (heat gun, hair dryer, etc.) WOODSTOVES WITh pEDESTAL BASE Step 3. Secure wires in the heat shrink tube to the fan cage using (3) Leg based units, see instructions on Page 6. wire ties making sure wires/heat shrink tube follow contour of inner side of blower cage. -
Page 5: Figure
Step 6. Locate the 3/8” diameter x 1/2” long bolt on the bottom of the firebox near the draft handle. Using a 9/16” wrench or socket loosen this bolt but do not remove from threaded hole. See Figure 20. Note: This bolt was holding the stoves shipping legs on the stove and should have been reinstalled with the other three bolts that were holding the shipping legs on the stove per the pedestal instructions. -
Page 6: Figure
Step 9. Using a 9/16” open end wrench tighten down the 3/8” bolt hold- WOODSTOVES WITh LEG BASE ing the control box. See Figure 23. Step . Using a 9/16” wrench or socket loosen the left heat shield bolt. This bolt is located on the bottom side of the leg heatshield as shown. -
Page 7: Figure
Step 3. Locate the tabs on the back of the control box. Slide the tabs Step 5. Plug the blower harness into plug on rear of snap switch bracket. onto the upper edge of the left side heatshield. See Figures 29 See Figure 32. -
Page 8: Figure
Figure 34 - Wiring Schematic NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.