Scag Power Equipment SW Operator's Manual

Sw series

Hide thumbs Also See for SW:

Operator's manual (70 pages)

Operator's manual (54 pages)

Operator's manual (39 pages)

Table Of Contents

Table of Contents

Quick Links

Summary of Contents for Scag Power Equipment SW

Page 1 MODEL SW THIS MANUAL CONTAINS THE OPERATING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG MOWER. READING THIS MANUAL CAN PROVIDE YOU WITH ASSISTANCE IN MAINTENANCE AND AD- JUSTMENT PROCEDURES TO KEEP YOUR MOWER PERFORMING TO MAXIMUM EFFI- CIENCY. THE SPECIFIC MODELS THAT THIS BOOK COVERS ARE CONTAINED ON THE INSIDE COVER.
Page 2 WARNING: FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all shields in place, especially the grass discharge chute. * Before performing any maintenance or service, stop the machine and remove the spark plug wire and ignition key. * If a mechanism becomes clogged, stop the engine before cleaning.
Page 3: Table Of Contents
TABLE OF CONTENTS MODEL SW SUBJECT PAGE Introduction ....................1 General Safety Instructions ................. 1 Signal Words ....................1 Symbols ....................... 2-3 Before Operating ..................4 While Operating ................... 4 Maintenance and Storage ................5 Initial Run-In Procedures ................6 Mower Operation ..................
Page 4: Table Of Contents
TABLE OF CONTENTS (CONTINUED) SUBJECT PAGE Illustrated Parts List Notes........................17 SWM-32", 36" Cutter Decks..............18-19 SWM-48", 52" Cutter Decks..............20-21 Notes........................22 Caster Assembly....................23 Engine Deck - 13KH, 15KH, 15KA, 17KA, 18HN........24-25 Engine Deck - 18KH................... 26-27 Handle Assembly..................28-29 Instrument Panel....................30 Peerless Transmission..................31 Engine Deck Wire Harness................32 Handle Wire Harness..................32...
Page 5: Introduction
We encourage you to contact your dealer for repairs. following signal words to attract your attention to safety All Scag dealers are informed of the latest methods to messages found on the decals and throughout this service this equipment and provide prompt and efficient manual.
Page 6: Symbols
ISO Symbols CE Mark SYMBOL DESCRIPTION SYMBOL DESCRIPTION Choke Transmission Parking Brake Spinning Blade 48071S On/Start Spring Tension on Idler Off/Stop WARNING Falling Hazard FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS SEE OPERATOR'S MANUAL 481109...
Page 7: Symbols
SYMBOL DESCRIPTION SYMBOL DESCRIPTION Fast Slow Cutting element - Basic symbol Continuously variable - Linear Pinch Point Cutting element - Engage 481039S Hourmeter/elapsed operating hours Cutting element - Disengage Keep bystanders away Read operator's manual...
Page 8: Before Operating
Scag optional grass catcher or mulching plate are properly installed. If the dis- 8. Fill the fuel tank with clean, fresh gasoline, with a charge area should plug, shut the engine off and wait minimum octane rating of 87.
Page 9: Maintenance And Storage
9. Always park the mower and/or start the engine on a 15. Use only Scag approved attachments and accessories. level surface. Scag Approved Attachments: GC-F4 10. If the cutting blades should strike a solid object or GC-4D the equipment should start to vibrate abnormally,...
Page 10: Initial Run-In Procedures
8. Allow the engine to cool before storing the mower in MOWER OPERATION any enclosure such as a garage or storage shed. 1. Read and understand the safety instructions Make sure the fuel tank is empty if the machine is to before attempting to operate this machine.
Page 11: Cutter Deck Belt Adjustments
END OF L-SHAPED -NOTE- BRACKET BELT When PTO is engaged or (possibly) disengaged, "J" BOLT a squealing sound from the underside of the machine is normal. It is caused by the electric clutch plates meshing as the cutter blades come up to speed.
Page 12: Transmission Drive Belt
TRANSMISSION DRIVE BELT CUTTER DECK ADJUSTMENTS Adjust the transmission drive belt so that there is about a Due to the many cutting conditions that exist, it is difficult 3/16" deflection with 10 lbs. of pressure. Adjust by to suggest a cutter deck setting that will work for every loosening idler pulley mounting bolt and sliding the idler lawn.
Page 13: Blade Height Adjustments
If blades are out of balance, vibra- tion and premature wear of spindle assembly can X Must NOT Exceed occur. See your authorized Scag dealer for 1/3 Blade Width SGB033 blade balancing or special tools if you choose to balance your own blades.
Page 14: Custom-Cut Baffle Adjustment
Custom-Cut Baffle Adjustment 2. Move the Custom-Cut Baffle to desired position. The Custom-Cut Baffle is designed to deliver optimum airflow and superior cutting performance in any type of (See Figures 10 through 12 for position) grass. The Custom-Cut Baffle can be raised or lowered to precisely tailor the deck's performance for the type of 3.
Page 15: Lubrication And Maintenance Chart
Chassis grease Grease transmission couplers Chassis grease Grease idler bracket LH & RH Chassis grease Check all hardware for proper tightness More often if needed Adjust air gap on electric clutch Contact your Scag dealer for information about making this adjustment...
Page 16: Troubleshooting Cutting Conditions
TROUBLESHOOTING CUTTING CONDITIONS CAUSE CURE CONDITION Stringers - Occasional Low engine RPM Run engine at full 3600 RPM Blades of Uncut Grass Ground speed too fast Slow speed to adjust for conditions Wet grass Cut grass after it has dried out Dull blades, incorrect sharpening Sharpen blades Deck plugged, grass accumulation Clean underside of deck...
Page 17 Deck plugged, grass accumulation Clean underside of deck Too much blade angle (deck pitch) Adjust pitch and level Deck mounted improperly See your authorized SCAG dealer Bent spindle area See your authorized SCAG dealer Dull blade Sharpen blade Width of Deck...
Page 18 Adjust pitch and level Ridge in Center of Cutting Path Bent blade Replace blade Internal spindle failure See your authorized SCAG dealer Mounting of spindle incorrect See your authorized SCAG dealer Width of Deck SGB024 Slope Cut - Sloping Bent spindle mounting area...
Page 19: Technical Specifications
TECHNICAL SPECIFICATIONS MODELS SW32-13KH, SW36A-13KH, SW36A-15KA, SW36A-15KH, SW48A-15KA, SW48A-15KH, SW48A-17KA, SW48A-18HN, SW52A-17KA, SW52A-18KH, SW52A-18HN ENGINE General Type: Heavy duty industrial/commercial Brand / Model: Kawasaki FH451V & FH500V: Kohler CV13T, CV15T, CV493T Honda GXV610QAF Horsepower: Kawasaki FH451V=15HP, FH500V=17HP Kohler CV13T=13HP, CV15T=15 HP, CV493T=18HP Honda GXV610QAF=18HP Type: Kawasaki 15 HP &...
Page 20 TECHNICAL SPECIFICATIONS (CON'T) DRIVE SYSTEM Type: Belt drive with twin power belts for increased friction to pulley surface. Transmissions: Peerless 5-speed transmission, Model #700-070A. Steering/Travel Control: Clutch/brake fingertip steering, key lock switch. (EZ Grip design allows minimum hand force to operate controls.) Brakes: 6"...
Page 21: Notes
NOTES...
Page 22: Swm-32", 36" Cutter Decks
32" & 36A" CUTTER DECKS SW-SWZ04CD36A...
Page 23 32" & 36A" CUTTER DECKS Ref. Part Ref. Part No. Number Description 32 36A No. Number Description 32 36A 461551 Cutter Deck (Includes Decals) 48100-02 Bronze Bearing 461634 Cutter Deck (Includes Decals) 04050-05 Retaining Ring, 1-1/8" Ext. ”E” 461663 Cutter Spindle Assy. 44078 J-Hook 43312...
Page 24: Swm-48", 52" Cutter Decks
48A, 52A" CUTTER DECKS 41, 41A 40 39 SW-SWZ04CD48, 52"...
Page 25 48A, 52A" CUTTER DECKS Ref. Part Ref. Part No. No. Description 48A 52A No. No. Description 48A 52A 461636 Cutter Deck (Includes decals) 04112-05 Nut, 1/2-13 Spiralock 04041-08 Flat Washer 3/4" Special 461643 Cutter Deck (Includes decals) 41A 04041-08S Flat Washer 3/4" Special 461663 Spindle Assembly 44078...
Page 26: Notes
NOTES...
Page 27: Caster Assembly
CASTER ASSEMBLY SW-SWZ2003CSTR Ref. Part Description 04066-01 Quick Pin 43037-01 Spacer, Caster Yoke, 1/2" Long 48100-01 Bronze Bearing 48114-04 Grease Fitting 46082 Support Assembly (Includes Items (3 & 4) 45006 Caster Yoke 04021-07 Elastic Stop Nut, 1/2-13 43022 Sleeve, Caster Wheel Bearing 04001-37 Hex Hd.
Page 28: Engine Deck - 13Kh, 15Kh, 15Ka, 17Ka, 18Hn
ENGINE DECK 15 KA 17 KA ONLY (1 loc.) 18 HN ONLY 40, 40A SW2004ED...
Page 29 04050-08 Retaining Ring, 1" Ext.- "E" 43085** Wheel Axle (SW36,48 & 52) 48200 Pulley, Wheel Drive 43104** Wheel Axle (SW 32) 43088 Spacer, Wheel Pulley 49070-7002 Muffler (Purchase from Kawasaki) 48209 Brake Drum 04001-08 Bolt, 5/16-18 X 3/4" Hex Head 04017-19 Bolt, 5/16-18 x 1-1/2"...
Page 30 ENGINE DECK SW52A - 18KH (x3) (1 loc.) 37, 37A SW18KHED...
Page 31 ENGINE DECK SW52 - 18KH Ref. Part Ref. Part Description Description 04102-04 Bolt, 7/16-20 x2-1/2" Hex Head 482854 Engine,18HP Kohler 04001-12 Bolt, 5/16-18 x 1-3/4" Hex Head (CV493T, Spec PS-27526) 04021-09 Nut, 3/8-16 Elastic Stop 48030-09 Cable Clamp 04040-15 Flat Washer, 5/16" 481580 Transmission, 5-speed 04017-19...
Page 32: Handle Assembly
HANDLE ASSEMBLY SW 2004 HA...
Page 33 HANDLE ASSEMBLY Ref. Part Ref. Part 13KH 18KH 15KA 18HN 13KH 18KH 15KA 18HN No. No Description No. No Description 15KH 17KA 15KH 17KA 04001-17 Bolt, 5/16-18 x 2" Hex Head 461597 Handle Assembly 04019-02 Nut, 1/4-20 Serrated Flange 421360 Belt Guard 04040-15 Flatwasher, 5/16 (.375 x .875 x .083) 04017-27...
Page 34: Instrument Panel
INSTRUMENT PANEL SW99IP Ref. Part 13KH 18KH 15KA 18HN Description 15KH 17KA 48717 Switch, Neutral Interlock 482814 Throttle Control 48946 Throttle Control 481687 Engagement Switch, Electric Clutch 48609 Key Switch (Includes hardware) 48023 Hour Meter (dealer installed) Screw, #10-32 x .50 Phillips Washer Head 04019-01 Nut, #10-32 Serrated Flange Hex Head 482711 Handle Wire Harness, Manual Start...
Page 35: Peerless Transmission
PEERLESS 700-070 FOR REFERENCE ONLY ORDER PARTS FROM PEERLESS / TECUMSEH REF. PART Ref. Part DESCRIPTION No. No. Description 778125 Spur Rear (35 teeth) 772083A Case, Transmisson 778239A Spur Gear (32 teeth-steel) 780086A Needle Bearing Grease Spec 778124A Spur Gear (30 teeth) 780142 Needle Bearing 778123A...
Page 36: Engine Deck Wire Harness
ENGINE DECK BLADE CLUTCH WIRE HARNESS KOHLER (18 HP) NEUTRAL KAWASAKI (15 HP & 17 HP) INTERLOCK GROUND HONDA (18 HP) WHITE BLACK W/RED STRIPE PART NO. 482683 BLACK BLACK BLUE WHITE WHITE YELLOW WIRE HARNESS ADAPTER - ENGINE INSTRUMENT SW04WH482683 PANEL HARNESS HANDLE WIRE HARNESS...
Page 37: Wire Harness Adapter-Honda (18 Hp)
WIRE HARNESS GROUND ADAPTER HONDA (18 HP) ENGINE STATOR PART NO. 482848 BLACK RECTIFIER CAPACITOR YELLOW YELLOW WHITE MAGNETO SW04WH482848 MAIN WIRE HARNESS WIRE HARNESS ADAPTER KAWASAKI (15 HP & 17 HP) PART NO. 481717 SW2003WH481717...
Page 38: Replacement Decals
482284 CHOKE FAST SLOW 481122 48314 32" - 48315 36" - 482297 48" - 481953 52" - 481954 482286 482816 CUTTING HEIGHT ADJUSTMENT DECK MOUNTING HOLE POSITION 48404 NUMBER OF CASTER SPACERS (BELOW SUPPORT) 48404 NUMBER OF SPACERS ABOVE CUTTER BLADES 1-7/8 2-3/8 2-1/8...
Page 39 INSTALL BELT COVER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL 481039 481039 WARNING WARNING DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCH MASTER, MULCH PLATE, OR ENTIRE GRASS CATCHER INSTALLED 482165 WARNING FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS SEE OPERATOR'S MANUAL 481109 481109...
Page 40 The expense of delivering the mower to the dealer for warranty work and the expense of returning it to the owner after repair will be paid for by the owner. Scag’s responsibility is limited to making the required repairs and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag mower.
Page 41 Scag autorizado distribuidor cortacésped entrega gasto gasolina, gasto limitarse pero incluyendo, tipo, otro cualquier consecuentes incidentales, daños alguna responsabilidad asume Scag implícita.
Page 42 NOTAS...
Page 43 aviso previo cambio sujetas Especificaciones 2003 Julio, publicación: Fecha lbs. lbs. lbs. lbs. GC-4D: césped recogedor Peso lbs. lbs. lbs. lbs. GC-F4: césped recogedor Peso lbs. lbs. lbs. lbs. Peso: 40.5" 40.5" 40.5" 40.5" césped: recogedor Altura 40.5" 40.5" 40.5" 40.5"...
Page 44 aviso previo cambio sujetas Especificaciones 2003 Julio, publicación: Fecha diámetro. 1-1/4" mango: Barras capas. neumática, cámara 6.50-6 13.0 motrices/Llantas: Ruedas litros) (19.0 galones costuras, Polietileno combustible: Tanque calibre Acero Espesor: MOTOR PLATAFORMA fabricante. especificación Consulte Variado válvula: Grupo fabricante. especificación Consulte Variado aceite:...
Page 45 Ancho autorizado doblado Scag distribuidor Consulte plataforma Alojamiento autorizado corte trayectoria Scag distribuidor Consulte interno Falla ancho través autorizado inclinadas Crestas Scag distribuidor Consulte doblada montaje Área inclinado Corte corte plataforma Ancho autorizado Scag distribuidor Consulte incorrecto Montaje...
Page 46 Ancho autorizado incorrectamente Scag distribuidor Consulte montada corte Plataforma llantas presión ajuste Revise disparejas Ruedas corte trayectoria llantas ancho presión ajuste Revise desequilibrada presión Llantas inclinadas Salientes corte plataforma Ancho irregular perfil volado corte dirección cambiar corte ondulada,...
Page 47 corte corte plataforma plataforma Ancho Ancho corte trayectorias entre cortar césped pase cada traslape Aumente pasadas entre insuficiente Traslape Franjas Vetas cuchillas Reemplace dobladas Cuchillas corte plataforma Ancho seque césped Corte mojado Césped terreno condiciones ajustarse para velocidad Disminuya alta demasiado Velocidad plataforma...
Page 48 Scag distribuidor Contacte eléctrico embrague entrehierro Ajuste necesario frecuencia mayor ajustada bien esté tornillería toda Verifique chasis Grasa derecho izquierdo lado polea soportes Engrase chasis Grasa transmisión acoplamientos Engrase chasis Grasa motriz rueda...
Page 49 personalizado personalizado corte Deflector Figura corte deflector 4" Posición Figura 2004 TOPE PLANA ELÁSTICA TUERCA ARANDELA Setting 4" 2004 MONTAJE MONTAJE TORNILLERÍA 4" AJUSTE TORNILLERÍA PARA AGUJEROS CARRO PERNO INFERIOR CONJUNTO personalizado corte deflector 3-1/2" 11.Posición Figura Figura (Vea corte. plataforma personalizado TOPE...
Page 50 Afiliado Figura cuchillas balancear prefiere especiales herramientas cuchilla balancear para SGB033 cuchilla ancho Scag autorizado distribuidor Consulte exceder debe eje. conjunto prematuro desgaste vibración producirse puede desbalanceadas, están cuchillas cuchilla. balance Revise cuchilla. quemar puede esmeriladora, corte lima.
Page 51 corte altura Ajuste Figura SC405G CORTE PLATAFORMA ALTURA AJUSTE libremente. moverse debe máquina neutral, posición bloqueadas están dirección palancas Cuando asas. 1/2") 1/4" hacia firmemente tiren dirección palancas ALTO CORTE hasta apliquen frenos modo dirección freno varillas Ajuste dirección 3/4") 1/2"...
Page 52 corte plataforma Correas Figura Figura (Vea CUCHILLA CORREA tipo perno tuerca aflojando apretando SC402G TENSIÓN AQUÍ VERIFIQUE tensión Ajuste presión. libras 1/2" mueva misma modo correa Ajuste DESCARGA misma. para tensión medidor usando corte ÁREA plataforma transmisión correa Ajuste correa. cubierta Retire CORTE...
Page 53 lubricadas. sido hayan conexiones 390S0138 todas asegurarse para preventiva revisión DESCONECTAR PARA ABAJO HACIA PRESIONE sólo Esto fábrica. aplicó lubricante ACCIONAR PARA ARRIBA HACIA TIRE conexiones. todas lubricante Aplique (OFF) apagado está accionamiento interruptor neutral está máquina arrancar cigüeñal girar debe motor encendido.
Page 54 481109 OPERADOR MANUAL SCAG APROBADOS CONDUCCIÓN revisar antes apagado estar debe motor DISPOSITIVOS SÓLO CAÍDA RIESGO tacómetro. motor velocidad ADVERTENCIA máxima verifique autorizado distribuidor haga precisión, seguridad asegurarse Para persona. alguna acerque cuando controlador. ajustes cambio...
Page 55 Llene área instalados. correctamente estén propiedad. personas otras mismos, Scag paja mezcla placa opcional césped ellos ocurran heridas accidentes recogedor cuando excepto lateral, descarga responsable evitar puede propietario/usuario corte...
Page 56 operador manual curiosos alejados Mantenga transcurridas operación Horómetro/Horas Desconectar cortante Elemento 481039S Accionar cortante Elemento contacto Punto básico Símbolo cortante Elemento Lineal variable Continuamente Lento Rápido DESCRIPCIÓN SÍMBOLO DESCRIPCIÓN SÍMBOLO...
Page 57 MANUAL OPERATOR'S 481109 ATTACHMENTS RIDING APPROVED SCAG ONLY HAZARD FALLING WARNING caída Riesgo Aceite Apagado/Parada Encendido/Arranque polea resorte Tensión 48071S giratoria Cuchilla estacionamiento Freno Transmisión Ahogador DESCRIPCIÓN SÍMBOLO DESCRIPCIÓN SÍMBOLO Marca Símbolos...
Page 58 (PRECAUCIÓN) parte gran dependen demás seguridad “CAUTION” señalización palabra originales. SCAG accesorios repuesto PRECAUCIÓN: piezas compre siempre seguridad, desempeño óptimo asegurar Para autorizado. Scag distribuidor contacte técnica, asistencia necesita importante reparación...
Page 59 ilustrada partes Lista después ..... garantía Declaración 34-35 ............... repuesto Calcomanías ....cables-Kawasaki mazo Adaptador ........-Honda cables mazo Adaptador ..............mango cables Mazo ..........motor plataforma cables Mazo ................Peerless Transmisión ................instrumentos Tablero 28-29 ................mango Conjunto 26-27 ..............
Page 60 CERTIFICATION TECHNICIAN SUPPORT 15-16 ................técnicas Especificaciones 12-14 corte........condiciones fallas Identificación ............Mantenimiento Lubricación Tabla ..........personalizado corte deflector Ajuste ..................corte Cuchillas ................corte altura Ajuste ..............corte plataforma Ajustes ................motriz control Ajustes ................transmisión Correa ..........corte plataforma correa...
Page 61 serie. número etiqueta aparece completo serie número siempre producto este refiera Cuando 9019999 9010001 desde serie números SW52A-18KH 9009999 9000001 desde serie números SW52A-18HN 8999999 8990001 desde serie números SW52A-17KA 9619999 9610001 desde serie números SW48A-18HN 8989999 8980001 desde serie números SW48A-17KA 8969999...
Page 62 EE.UU. IMPRESO INC. MAYVILLE, METALCRAFT DIVISION 2003 JULIO IMPRESO Equipment Power Scag 03130 PARTE 2003 © INCLUIDA. INFORMACIÓN TODA MÁQUINA, OPERAR ANTES INTERIOR. CUBIERTA INDICADOS ESTÁN MANUAL ESTE CUBIERTOS ESPECIFICOS MODELOS EFICIENCIA. MÁXIMA TRABAJANDO CORTACÉSPED MANTENER AJUSTE PROCEDIMIENTOS MANTENIMIENTO AYUDAR...

This manual is also suitable for:

Sw32-13kh Sw36a-13kh Sw32-15ka Sw36a-15ka Sw36a-15kh Sw48a-15ka ... Show all

Scag Power Equipment SW Operator's Manual

Subject Page

Table of Contents

Quick Links

Related Manuals for Scag Power Equipment SW

Summary of Contents for Scag Power Equipment SW

This manual is also suitable for:

Table of Contents